Elk Navigator -M1KPNAV Specification, Installation And Setup

NOTE: M1 fi irmware v5.2.8 or l later is required in
order for Nav vigator to synchroniz ze and display the
names of Area as, F Keys, Lights, O Outputs, and Tasks.
ElkRP softwa are v2.0.10 is recomm mended when
programming g a M1 system that i ncludes a Navigator
Mounting g
Navigator can n be wall mounted without a pre-wire
box. If a pre- -wire box is used, i it MUST BE a sing
(1) gang elec trical box designed d for "New Work",
it should be in nstalled sideways ( (horizontal).
Separate the N Navigator front ass sembly from the
backplate by gently inserting a s small flat blade
screwdriver i nto each of the fou ur (4) locking slots
at a time unti l the front releases . Be cautious when
handling the front assembly. Av void touching or
damaging any y exposed compon ents. Do not bend
pull on the fla at ribbon cable that t loops over the bot
edge and plug gs into the back of the board.
Insert data bu us cable through ma arked entry. Positi
backplate lev vel on the surface w with TOP facing up
Install min. tw wo screws in moun nting holes provide
Warning: Sin ngle gang electrica al boxes designed f
"Old Work" have a wide outer trim dimension an
may not be su uitable for use with h Navigator. Insta
should test fi it before installatio on!
Locking slots x 4
This way
TOP UP
Mounting holes x 4 4
Locking slots x 4
N Navigator Backplate
NOTE: An op ptional surface box x (ELK-M1BBKN)
available for use on concrete or block (non-hollow
surfaces, or w where wire raceway y is needed.
Wirin ng Connectio ns
Splice the four (2) wires on the plug-in cabl
.
Data B Bus Cable wire from m the Control. Use
connec ctor splices or solde er and tape the con
r.
4 Con nductor Data Bus Cable
{CA AT5 is strongly recommended }
Rear
Keypad Cable
View
e
Assem mbly
WHITE
BLACK (-)
gle
WHITE (B)
GREEN (A)
and
RED (+)
* Connec ctor J1 has two
BLU UE
pins mar rked "RS485 ."
BRO WN
A jumper r "shunt' is
provided for placement
T o BROWN Wire
on these pins ONLY IF
To BL LACK (Neg) Wire
this keyp pad is the last
Optiona l programmable Output from
one device on n the data bus.
DO NOT T place jumper
n
on any ot ther pins of J1.
To BLUE Wire
N.C.
To BLACK (N Neg) Wire
or
Optional progra ammable Input "Keypad Zon
ttom
The opti ional Zone Input # and Output t # is determined by the Keypa
Keypad A Address Zone # Output # Keypad Address
1 1 193 193 9
2 2 194 194 10
3 3 195 195 11
ion
4 4 196 196 12
5 5 197 197 13
.
6 6 198 198 14
d.
7 7 199 199 15
8 8 200 200 16
NOTE: Connector TB1 (6 pin) is fo or the 6-wire Keypad Cable
for
TB2 (3 pin) is for a special RS232 2 cable (sold separately) us
nd
optiona l PC Software Utility Progr ram for flashing the firmwa
quickly s setting up the Installer info rmation page . Call Elk for
aller
Brown
Wht/Brn
CAT T5 or
Orange
Wht/Blue
CA AT6
Green
Blue/Wht
Ca able
Wht/Org
Wht/Grn
Blue pair is
not used
Conn ections if using CAT5 Wire e and a ELK-M1DBH Hub
Re-a ttaching Fron nt to Backplat
Plug th he 6-wire cable ass embly into connec
the boa ard. The polarity r ribs should face the
When removing this cabl le, always grip the
body it tself. DO NOT TU UG OR PULL on th
Tuck l loose cable and spli ices out of the way
Positio on the bottom edge of Navigator insid
ledge o of the backplate, an nd then rotate the to
toward ds wall. Gently pre ess until the 4 snaps
the slo ots. DO NOT FOR RCE! If units do no
) is
togethe er, start over doubl le checking for any
w)
wires o of connections whi ich may be interferi
Start-Up Scre een
le to the On power up the S Start-up screen disp
e "B" Version, M1 Seria al number, and the d
nnections. only IF the keypad d is currently set wi
ELK-M1KP PNAV
TB1 TB2
1
6
J1
*
+
Load (5 0mA max )
-
I.E. LE ED, Relay
m Keypad
2,200 Ohm
Resistor Colors
2,20 00
4 Band 5 Band
Ohm m
N.O.
Red Red
EOL L *
Red Red
Red Black
ne"
Brown
A message along t the bottom "Please
d Address .
Zone # Output #
Address" will disp play if a keypad add
201 201
currently set. Othe erwise the message
202 202
203 203
"Waiting to conne ct to panel". This
204 204
205 205 Navigator receives s valid data from th
206 206
207 207
208 208
Change (Set K Keypad) Addres
e Assembly.
Each Keypad conn nected to an M1 mu
sed by an
re and/or address, unique to any other keypad(
r details.
Press "CHANGE A ADDRESS" on the
+
R RED (+) to bring up the Set t Keypad Address s
-
BL LACK (-)
A GR EEN (A)
A1 WH HITE (B)
B
B1
te
tor TB1 on
e side gap.
connector
he wires.
y.
The current keypad d address will be il
address(s) with a R RED border indicat
de the lower
currently enrolled to the M1 panel. R
op back
addresses CANNO OT be used for this
s engage in
ot snap
Pressing any unuse ed keypad address
y loose
select that address for this particular k
ing.
Default Key ypad - Pressing the
button will c clear the keypad ad
plays the keypad
number enro olled into the panel
data bus address
task names, lighting names and
ith an address.
names. It wi ill not clear installe
EXIT – Pres ssing this button or
right corner r will exit the Set K
Data Bus s Enrollment
A message " "Please enroll keyp
display if th he keypad address d
address curr rently enrolled in th
previously b been enrolled into a
Perform a B Bus Enrollment usin
keypad OR the ElkRP Remote
Set Keypad
dress is not Once the ke eypad receives valid
e will display panel (and i is enrolled) it will d
displays until
"Synchronis sing Panel Status".
he panel.
ss
ust have its own
(s) on the system.
e Start Up screen
screen.
The Start-up p screen displays u
data is colle ected from theM1 p
complete th e keypad will mov
MAIN USE ER screen.
lluminated. Any
te a keypad
RED bordered
keypad.
button should
keypad.
"Default Keypad" "
ddress, M1 serial
l, function key nam mes,
d output names and d area
er information.
r the Red "X" in th e top
Keypad Address scr reen.
pad into panel" wil l
does not match an
he M1, or has neve er
any M1.
ng an already enrol lled
e Program software e.
d data from the M1 1
display the message e
until all current statu us
panel. Once this is
e on to the followin ng