SERVICE MANUAL LED TV Model No. MSDV1636-O3 MSD306 Chassis WARNING This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Service Manual Model No.: Chapter 1: General Information 1-1. Table of Contents 1. General Information................1-1. Table of Contents 1-2. General Guidelines 1-3. Important Notice 1-4. How to Read this Service Manual 6SHFL¿FDWLRQV..................3. Location of Controls and Components........... 3-1.
Page 3
Service Manual Model No.: 9. Trouble-shooting………….............. 9-1. Simple Check 9-2. Main Board Failure Check 9-3. Panel Failure - 02 -...
Service Manual Model No.: 1-2. General Guidelines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Service Manual Model No.: 1-3-6 Safety Check after Repairment &RQ¿UP WKDW WKH VFUHZV SDUWV DQG ZLULQJ ZKLFK ZHUH UHPRYHG LQ RUGHU WR VHUYLFH DUH SXW in the original positions, or whether there are the positions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades.
Service Manual Model No.: Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
Service Manual Model No.: 1-3-8. Photo used in this manual The illustration and photos used in this Manual may not base on the final design of products, which may differ from your products in some way. 1-4. How to Read this Service Manual Using Icons: ,FRQV DUH XVHG WR DWWUDFW WKH DWWHQWLRQ RI WKH UHDGHU WR VSHFL¿F LQIRUPDWLRQ 7KH PHDQLQJ RI each icon is described in the table below:...
Service Manual Model No.: 6SHFL¿FDWLRQV Model MSDV1636-O3 Screen Size 15.6 inch Aspect Ratio 16:9 Resolution 1366x768 6.5 (GRAY TO Response Time (ms) GRAY) Angel of View 80(H)/45(V) Color Display 262,144K No. of Preset Channels 400 OSD Language English Color System...
Service Manual Model No.: 3. Location of Controls and Components 3-1 Board Location A Board B Board Description A Board Main Board 515C3206M09 514C1601M01 B Board Power Board LVDS 30444005301 3-2 Main Board - 08 -...
Service Manual Model No.: 3-2-1 Function Description: Main Board Process signal which incept from exterior equipment then translate into signal that panel can display. &RQQHFWRU GH¿QLWLRQ Main board connector Power connectors (J2) Pin number Signal name BK ON /OFF POWER ON/OFF +5VSTB +12V...
Page 11
Service Manual Model No.: Keypad andremote connector (J28) STANDBY Speaker connectorJ26 Pin number Signal name Description RSPK+ RSPK+ RSPK- RSPK- LSPK- LSPK- LSPK+ LSPK+ - 10 -...
Service Manual Model No.: 3-3. Power Board 3-3-1 Function Description: Supply power for Main board, Panel. &RQQHFWRUGH¿QLWLRQ Pin number Signal name Pin number Signal name +12V POWER ON/OFF +12V +12V +5VSTB BK ON /OFF - 11 -...
Service Manual Model No.: 3-4. LED Panel 316156WB111(CLAA156WB 11A) - 12 -...
Page 14
Service Manual Model No.: 3-4-1 Function Description: Display the signal. &RQQHFWRU GH¿QLWLRQ Pin No. SYMBOL FUNCTION DIAG_LOOP Pin 1 & 34 must be connected together on the inverter board Power Supply, 3.3 V (typical) Power Supply, 3.3 V (typical) V EEDID DDC 3.3V power Clk EEDID...
Page 15
Service Manual Model No.: No connection No connection No connection No connection No connection No connection VSSLED Ground – LED VSSLED Ground – LED VSSLED Ground – LED DIAG_LOOP Pin 1 & 34 must be connected together on the inverter board System PWM Signal Input (+3.3V Swing) LED_EN LED enable pin (+3.3V Input)
Service Manual Model No.: 4. Disassemble and assemble 4-1 Remove the Pedestal 4-3. Remove the adhesive tape (The location of the adhesive tape as follows) /D\ GRZQ WKH XQLW VR WKDW UHDU FRYHU faces upward 5HPRYH WKH WKUHH VFUHZ IURP WKH UHDU FRYHU LQGLFDWHG ZLWK Remove the front frame on the ¿JXUH DERYH...
Service Manual Model No.: 4-4 Remove the Main board 5HPRYH WKH WZR VFUHZ LQGLFDWHG RQ 'LVFRQQHFWHG WKH FRXSOHU - - WKH ¿JXUH DERYH E\ - - - - - 5HPRYH WKH 0DLQ ERDUG 4-5 Remove the power module take out the Power board - 16 -...
Service Manual Model No.: 4-7 Remove the speaker Take out the speaker 4-8 Remove the remote control Remove the screw, take out the remote control board - 17 -...
Service Manual Model No.: 5. Installation Instructions 5-1 External Equipment Connections Accessories Battery User GUIDE Remote Control Antenna Connection Connect one end of a coaxial cable (not included) to the ANT IN jack on the back of your TV/DVD combo, then connect the other end of the cable into the antenna or cable TV wall outlet.
Page 20
Service Manual Model No.: AV EQUIPMENT You can use the input terminals on TV set rear as follows. AV OUTPUT HDMI1 PC AUDIO VIDEO EQUIPMENT TO VIDEO INPUTS HDMI TO AUDIO INPUTS VIDEO EQUIPMENT with YPbPr (component) output Yellow (video) White(audio L) Red(audio R or Pr) Blue(Pb)
Page 21
Service Manual Model No.: AV OUTPUT STEPS: HDMI1 PC AUDIO Be sure both the TV and computer are set to Power off. 1.Connect VGA and audio cable. 2.Connect the power cord. 3.Power on the TV, switch to PC mode. 4.Power on the PC. This sequence is very important.
Service Manual Model No.: 5-2 HDMI Connections When the source device(DVD player or Set Top Box) supports HDM How To Connect 1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product). 2.
Page 23
Service Manual Model No.: Cable sample HDMI Cable (not supplied with the product) HDMI to DVI Cable ( not supplied with the product) Analog Audio Cable (Stereo to RCA type) (not supplied with the product) - 22 -...
Page 24
Service Manual Model No.: Power source TO USE AC POWER SOURCE Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard polarized AC outlet. NOTES: 1HYHU FRQQHFW WKH $& OLQH FRUG SOXJ WR RWKHU WKDQ WKH VSHFL¿HG YROWDJH Use the attached power cord only.
Service Manual Model No.: 6. Operation Instructions Basal information 6-1 Front panel controls SOURCE MENU VOL+ VOL- STANDBY 1 SOURCE: Display the input source menu. 2 MENU: Display main MENU. 3 CH+/CH- In TV mode, press CH+ or CH- to change the channel up and down. In MENU mode, press CH+ or CH- to select items.
Service Manual Model No.: 6-3 Setting Up Your Remote Control REMOTE CONTROL 1:POWER:To set the TV to standby or power on. :In USB mode, used as reverse key, in teletext mode used as subpage key. : In USB mode, used as forword key, in teletext mode used as reveal key.
Page 27
Service Manual Model No.: 6-3 Setting Up Your Remote Control TELETEXT Teletext is an information system broadcast by certain channels which can be consulted like a newspaper. It also offers access to subtitles for viewers with hearing problems or who are not familiar with the transmission language (cable networks, satellite channels, etc.) Press: You will obtain :...
Service Manual Model No.: 7-3 .Wiring Connection Diagram Name Material No. Connection Wire(For Speaker) Connection Wire(Power For Mainboard) 30444005301 LVDS Wire Connection wire(12V input for power board) Connection Wire(For Keyboard and Remote) - 38 -...
OPERATION 8.Measurements and adjustments Installation Guide Please select an OSD Language Cesky English Magyar Polski Fran ais Espanol Dansk Hrvatski Nederlands Portugues Deutsch Italiano Norsk Pycck Country Australia Bulgaria Denmark Germany Italy Austria Croatia Finland Greece Luxembourg Belgium Czech France Hungary Netherlands This screen only appears when the TV is turned on for the first time, or reset to factory settings.You can choose...
Page 42
OPERATION 2).DTV Manual tuning: You can select a DTV channel then find the program in this channel. Press to select the channel, then press OK to search the programs . NOTE: The Bad Normal Good bar graph on this screen shows signal intensity. DTV Manual Tuning VHF CH Press OK to search...
OPERATION Favourite Press to choose the program, press FAV button, it will show on the right side of the program. Choose the FAV program, press FAV button again, you can cancel the FAV, will disappear . Once your favorite group is created, you can press the FAV key to quickly access your favourite channel. 2.
OPERATION 5.OPTION MENU To enter the Option Menu, press MENU button and the press buttons to select the Option Menu. Once in Option Menu, press buttons to select the settings you wish to adjust. Press MENU button to return to the Main Menu. OSD Language English Audio Languages Subtitle Languages...
Page 45
OPERATION Sample1.ts Resolution: 720x576 AudioTrack: ½ Subtitle: Program: Size: 30574 KBytes Close 8.EPG Menu (Electronic Program Guide). The EPG Menu is used to look at what is being broadcasted in DTV or Radio modes. Press the EPG Button to access the EPG Menu. You will receive detailed program information of the channel you are currently watching as well as the 7 Day Program guide.
Service Manual Model No.: 8.1 How to enter into the factory model 1. You can press "source-2-5-8-0" to go into factory setting. Presse the key "exit" to shut the factory setting. content: 1: ADC setup: set ADC value of YUV,VGA. It can also be auto-set. Adopt 100% color bar to yuv and Checkerboard signal to vga.
Service Manual Model No.: 8.2 How to update software Haier MSD306 F/W upgrade with USB SOP Step 1: Ready for F/W Upgrade 1.1 Prepare a USB memory . &RS\ WKH VRIWZDUH ¿OH PHUJELQ IURP \RXU FRPSXWHU WR WKH 86% PHPRU\ DQG UHPRYH it from computer’s USB port! Step 2: F/W Upgrade 2.1 AC ON...
Service Manual Model No.: 9-2. Main board failure check 1) Black creen Is power LCD normal? Check QS,Q6 and the 2) White screen on VCC pins of CJ20 Check if Q1is working Signal on CJ20 Check if CJ20 is - 47 -...
Page 50
Service Manual Model No.: 3) Panel display abnormally connector j20 is at normal level - 48 -...
Page 51
Service Manual Model No.: 4) No sound No sound Check the input Check if there is sound input source signal Check if the volume control is Reset at 0 level or muted volume Check the Check if there is output at CJ26 speakers Check if the power supply...
Page 52
Service Manual Model No.: 5 TV failure TV no channel Fix the RF Check if there is RF signal input Check the power Check if there is supply circuit to +5V at PIN6 of this PIN TUU2 Check if there is I2C signal at PIN4 &...
Page 53
Service Manual Model No.: 6) HDMI no picture or picture abnormal If J3 is R111,R112,R113,R114,R116, R117 Q11,Q12 - 51 -...
Page 54
Service Manual Model No.: 7) PC no picture or picture abnormal - 52 -...
Page 55
Service Manual Model No.: 8) YPBPR, AV, SCART no picture or picture abnormal Check Y - 53 -...
Page 56
Service Manual Model No.: 9-3. Pannel failure Failure Mode Part Name Description Phenomena Failure cause Block Defect :TCP cracking or cracking Dim or L/D :TCP Sunken V B/D Vertical bar :TCP lead cracking :ACF bonding short :Awful environment and something electric enter V Dim Vertal gray line into LCD...
Page 57
Service Manual Model No.: Part Name Description Phenomena Failure cause I n c o m i n g I n s p e c t i o n Standard Bright dot dark dot in Dot Defect pannel Bladder between Polarizer and top glass Polarizer Bubble Bladder in Polarizer...
Page 58
Service Manual Model No.: Failure Mode Part Name Description Phenomena Failure cause White Screen B/L normal, only white screen display M a y b e c a u s e d by surge current Black Screen B/L normal, and EDS only Black screen display FIIcker...
Page 59
Service Manual Model No.: Failure Mode Part Name Description Phenomena Failure cause Mechanlcal When Caused Nolse turn panel,appear b y M e c h a n i c a cacophony noise of backlight unit Ripple Connectric circle Causeed by between mechanism and pannel B/L off...
Page 60
Service Manual Model No.: Failure Mode Part Name Description Phenomena Failure cause Brightness B/L unit badness at bottom of LCM Light leakage brighter than normal B / L b r i g h t n e s s Sheet in B/L unit Mechanlcal or B/ asymmetric is uneven...