Snapper 2812523BVE Safety Instructions & Operator's Manual
  1. Manuals
  2. Brands
  3. Snapper Manuals
  4. Lawn Mower
  5. 2812523BVE
  6. Safety instructions & operator's manual

Snapper 2812523BVE Safety Instructions & Operator's Manual

Rear engine riding mower series 23
Hide thumbs Also See for 2812523BVE:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual
CUTTING WIDTH
ENGINE HP *
SERIES DESIGNATION
28
28" Cutting Deck
11 – 11.0 HP Engine
-
30
30" Cutting Deck
115 – 11.5 HP Engine
-
33
33" Cutting Deck
12 – 12.0 HP Engine
-
125 – 12.5 HP Engine
13 – 13.0 HP Engine
Thank you for buying a SNAPPER Product! Before operating your machine, read this manual carefully and pay
particular attention to the "IMPORTANT SAFETY INSTRUCTIONS" on Pages 2 thru 4. Remember that all power
equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in
accordance with the operating instructions and common sense!
NOTE: Specifications are correct at time of printing and are subject to change without notice.
* Actual sustained equipment horsepower will likely be lower due to operating limitations and environmental factors.
COPYRIGHT © 2005
SNAPPER – A DIVISION OF SIMPLICITY MFG., INC.
ALL RIGHTS RESERVED
Safety Instructions & Operator's Manual for
REAR ENGINE RIDING MOWER
MODEL NUMBER EXPLANATION
33
15
135
13.5 HP Engine
-
15 – 15.0 HP Engine
16 – 16.0 HP Engine
17 – 17.0 HP Engine
281123BV
2811523BV
281223BVE
2812523BVE
2813523BVE
301123BV
3011523BV
23
K
V
23
Series Designation
-
SERIES 23
MODELS
301223BVE
3012523BVE
3013523BVE
331323HVE
331523KVE
331623BVE
331723BVE
E
ENGINE OPTIONS
ENGINE MODEL
B - Briggs Engine
V
K - Kohler Engine
E
H - Honda Engine
MANUAL No. 7100310 (I.R. 7/14/2005)
ENGINE TYPE
Over Head Valve
-
Electric Start
-

Advertisement

Table of Contents
loading

Related Manuals for Snapper 2812523BVE

Summary of Contents for Snapper 2812523BVE

  • Page 1 17 – 17.0 HP Engine 13 – 13.0 HP Engine Thank you for buying a SNAPPER Product! Before operating your machine, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 thru 4. Remember that all power equipment can be dangerous if used improperly.

  • Page 2: Important Safety Instructions

    If you have any questions pertaining to your machine which your dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-935-2967).
  • Page 3 6. DO NOT fill fuel containers inside a vehicle or loads to hitch plate as specified with SNAPPER on a truck or trailer bed with a plastic liner. attachment instructions.
  • Page 4 14. Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices. 15. Maintain or replace safety and instruction labels...

  • Page 5: Table Of Contents

    TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ................2-4 TABLE OF CONTENTS ..................... 5 SECTION 1 - FAMILIARIZATION ..................6 SECTION 2 - OPERATING INSTRUCTIONS ...............7-13 Pre-start Checklist ......................7 Operator’s Seat Adjustment ..................7 Starting & Stopping Engine, Blade & Wheel Drive..........8-11 Starting &...

  • Page 6: Section 1 - Familiarization

    Section 1 - FAMILIARIZATION IMPORTANT: The figures and illustrations in this manual are provided for reference only and may differ from your specific model. Contact your Snapper dealer if you have questions. STEERING WHEEL FUEL TANK ENGINE SPEED TRANSMISSION CONTROL...

  • Page 7: Section 2 - Operating Instructions

    Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST 2.2 OPERATOR’S SEAT ADJUSTMENT Make the following checks and perform the service 2.2.1. FRONT TO REAR ADJUSTMENT required before each start-up. 1. With the engine stopped, loosen the two adjusting 2.1.1. Check tires and add or release air as needed knobs and move seat to desired position.

  • Page 8: Starting & Stopping Engine, Blade & Wheel Drive

    Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION TO START ENGINE, 2.3.1. ENGINE (ELECTRIC START) PUSH CLUTCH/BRAKE IMPORTANT: When the ignition key is turned to PEDAL ALL THE WAY “START”, the engine will turn over, but will not start DOWN unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the “OFF”...

  • Page 9: Starting & Operation

    Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 4. Open vent on fuel filler cap by turning 2.3.1. ENGINE (ELECTRIC START) (Continued) counterclockwise. NOTE: Failure to open vent on 8. Should the battery be too weak to start the engine, the fuel filler cap can cause engine to stall.

  • Page 10: Starting & Stopping Mower Blades

    3 seconds, the blade brake and hazards before and while backing. must be adjusted. Refer to Section “BLADE BRAKE ADJUSTMENT” for adjustment procedures or return machine to an authorized SNAPPER dealer for DEPRESS CLUTCH/BRAKE adjustment. DO NOT CONTINUE to operate machine...
  • Page 11 3 seconds, the blade brake must be adjusted. Refer to Section “BLADE BRAKE ADJUSTMENT” for adjustment procedures or return machine to an authorized SNAPPER dealer for adjustment. DO NOT CONTINUE to operate machine until blade brake is adjusted and functioning properly.

  • Page 12: Parking Brake

    Section 2 - OPERATING INSTRUCTIONS 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.5. CUTTING HEIGHT ADJUSTMENT 2.4.4. PARK BRAKE 1. Adjust cutting height as desired to any one of 1. Engage park brake by pushing clutch/brake pedal five positions using deck lift lever. Move deck lift “DOWN”...

  • Page 13: Reverse Lockout Mechanism

    DO NOT operate machine if Reverse Lockout and while backing. Mechanism is not functioning properly. Contact your local Snapper dealer for assistance. We realize that this could cause a change to your previous mowing method but we encourage you to adjust to this new system.

  • Page 14: Section 3 - Maintenance Instructions

    To retain the quality of the Rear Engine Rider, use for recommended service procedures. genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service 3.2.3. CHECK MOWER BLADE assistance. For the correct part or information for a particular Rear Engine Riding Mower, always mention 1.

  • Page 15: Check Blade Drive Belt

    Refer to Section should be 1-1/4” but no less 1”. If the measurement “BLADE BRAKE ADJUSTMENT” or contact your is less than 1”, the belt tension should be adjusted. SNAPPER dealer for assistance. Refer Section “BLADE...

  • Page 16: Check Interlock System

    Contact your 2. Change air filter. Pull up and rotate the air cleaner authorized Snapper dealer if you have questions. latch to remove cleaner cover. See Figure 3.4. IMPORTANT: When cover is removed, you are viewing the carburetor side of the air filter, which will appear clean.

  • Page 17: Battery Fluid Level

    Section 3 - MAINTENANCE WARNING SPINDLE GREASE FITTING DO NOT attempt any adjustments, maintenance or service with the engine or blades running. Stop blades. Stop engine. Engage parking brake. Remove key. Remove spark plug wires from spark plugs and (gas only) secure wires away from spark plugs. Engine and components are HOT.

  • Page 18: Rear Axle Bearing - Lubrication

    Figure 3.9. 4. To check lubricant in chain case, remove fill/level plug and look for lubricant on the internal components of the chain case. If no lubricant is visible, add SNAPPER transmission grease as needed. See Figure 3.9. AXLE BOOTS FIGURE 3.7...

  • Page 19: Service - Annually

    Replace worn or damaged parts with key. Remove spark plug wire from spark plug and genuine SNAPPER replacement parts available secure away from plug. Engine and components from an authorized SNAPPER dealer. are HOT. Avoid serious burns, allow all parts to 3.5.1.

  • Page 20: Section 4- Adjustments And Repair

    Remove spark plug wire from spark plug and described above, take machine immediately to an secure away from plug. Engine and components are authorized Snapper dealer. HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent 3”...

  • Page 21: Mower Deck Adjustment (Side To Side Levelness)

    Section 4 - ADJUSTMENTS & REPAIR 7. Move lift arm up or down as required until blade WARNING tips are within 1/8” of each other. See Figure 4.3. DO NOT attempt any adjustments, maintenance, 8. Tighten shoulder bolt & nut loosened in Step 6. service or repairs with the engine running.

  • Page 22: Mower Drive Belt Adjustment - 28" & 30" Decks

    “ON”, measures 1-1/4”. 8. Retighten hardware that secures clamp. Make sure hardware is tightened securely. IMPORTANT: The SNAPPER Rear Engine Rider Models with 33” decks do not require belt tension adjustment. But, if front frame assembly clamp is loosened for any reason, recheck belt spacing between idler pulley and belt.

  • Page 23: Rear Engine Rider Drive Components

    9. Retest wheel brake. CHAIN 4.3 REAR ENGINE RIDER DRIVE COMPONENTS CASE Your Snapper rider is equipped with a patented smooth start clutch. The clutch should operate smoothly and provide ample traction. If problems are CLUTCH experienced, contact your Snapper dealer for repair.

  • Page 24: Mower Blade Replacement

    Section 4 - ADJUSTMENTS & REPAIR 5. Inspect condition of blade. See Figure 4.11. WARNING 6. If blade is in good condition, sharpen at 22 to 28 DO NOT attempt any adjustments, maintenance, degrees. DO NOT sharpen beyond existing cutting service or repairs with the engine running.

  • Page 25: Mower Drive Belt Removal/Replacement - 28" 30" & 33" Decks

    Section 4 - ADJUSTMENTS & REPAIR 9. Route belt onto spindle pulley. Make sure belt is WARNING inside spindle belt guide and idler belt guide. Route DO NOT attempt any adjustments, maintenance, belt as shown in Figure 4.15 or 4.16. service or repairs with the engine running.

  • Page 26: Battery Removal, Replacement, Service

    Section 4 - ADJUSTMENTS & REPAIR WARNING POSITIVE TERMINAL POSITIVE (+) INSULATOR DO NOT attempt any adjustments, maintenance, CABLE service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and BLACK secure away from plug.
  • Page 27 Section 4 - ADJUSTMENTS & REPAIR WARNING WARNING The electrolyte (acid) produces a highly explosive gas. DO NOT attempt to charge battery while installed on Keep all sparks, flame and fire away from area when the Riding Mower. DO NOT use “BOOST” chargers on charging battery or when handling electrolyte or the battery.

  • Page 28: Accessories

    7061987......Ninja Recycling (Cover)........All 41” & 42” Deck Rear Engine Riders 7061910......Utility Trailer * WARNING 7061911......Aerator Catcher bags used on SNAPPER products are 7061912......Dethatcher made of woven fabric, and thus are subject to 7061913......Lawn Sweeper deterioration and wear during normal usage.

  • Page 29: Troubleshooting

    3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug. Recoil Starter 4. Faulty parking brake, blade or ignition switch. 4. Contact authorized SNAPPER dealer. 5. Park brake not engaged. 5. Engage park brake. 6. Ignition is in the OFF position.
  • Page 30 2. Rubber drive disc is not tracking properly on 2. Adjust rubber drive disc. drive disc. 3. Tapered axle bolt and nut missing. 3. Replace with SNAPPER tapered bolt & nut. 4. Axle bearing seized. 4. Contact authorized SNAPPER dealer. 5. Insufficient lubrication in chain case or 5.

  • Page 31: Maintenance Schedule

    MAINTENANCE SCHEDULE SUBJECT SERVICE REFERENCE EACH EACH HOURS HOURS HOURS HOURS SEASON TO BE PERFORMED PAGES Engine Check Oil Level Page 7 Engine Initial Oil Change Page 14 Engine Periodic Oil Change Page 16 Air Pre-Cleaner Service Sponge Pre- Engine Manual Cleaner Element Air Cleaner Replace Element...

  • Page 32: Maintenance/Replacement Parts

    MAINTENANCE/REPLACEMENT PARTS MAINTENANCE PARTS Engine Speed Control (Briggs Engine) 7022751 Engine Speed Control (Kohler Engine) 7074320 Engine Speed Control (Honda Engine) 7075089 Clutch/Brake Cable 7022449 Clutch/Brake Cable (33” Deck Models Only) 7074131 Brake Cable 7072648 28” Cutter Blade (Standard - Not Air Lift Compatible) 7035635 28”...

  • Page 33: Warranty

    For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.

  • Page 34: Primary Maintenance

    PRIMARY MAINTENANCE...
  • Page 35 PRIMARY MAINTENANCE...
  • Page 36 PRIMARY MAINTENANCE...

  • Page 37: Primary Maintenance

    PRIMARY MAINTENANCE...

  • Page 38: Product Registration Form

    Date of Purchase ___________________________________________________________ Retailer____________________________________________________________________ Retailer’s Phone Number ____________________________________________________ It is very important that you register your purchase with Snapper to ensure warranty coverage. Please mail your product registration card to: Snapper at P.O. Box 777, McDonough, Georgia 30253. Or you may register on line at www.snapper.com.
  • Page 39 NOTES ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________...
  • Page 40 Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA.

This manual is also suitable for:

281123bv281223bve2813523bve301123bv301223bve3013523bve ... Show all

Table of Contents