Advertisement
CONNECTIONS, INSTALLATION
Connections
Monitor
1
Digital video recorder
or time-lapse VCR
: VIDEO IN
: VIDEO OUT
A A A A Connections
What you will need
• Peripheral equipment (such as monitor, digital video recorder or
time-lapse VCR)
• Cables for connecting peripheral equipment and camera
(coaxial cables, connecting plugs)
• Power adapter (24 V AC or 12 V DC)
• Attachable lens (Auto-iris lens recommended.)
Coaxial cables supported
You can use any of the following coaxial cables:
• RG-59U (3C-2V) Length: About 250 m max.
• RG-6U (5C-2V) Length: About 500 m max.
• RG-11U (7C-2V) Length: About 600 m max.
CAUTION
• When using an RG-59U (3C-2V) cable, do not use it on piping or air
wiring.
• Select the cable to use according to the distance between the devices to
connect.
• If you use a cable other than the types above, the image or sync signal
will be attenuated and will not be transmitted correctly.
Attaching a lens
The 1/3-inch DC-type, CS mount auto-iris lens (sold separately) is
recommended.
1
Remove the lens cap.
2
Attach the lens.
Turn the lens slowly to attach it to
the camera.
3
Connect the lens plug to the
LENS terminal.
3
CAUTION
• Depending on the type of lens, the shape of the lens plug may differ. In
this case, contact the place of purchase or a Sanyo Authorized Service
Center.
• When attaching the lens, use a lens with a mount screw
(L) that is less than 7 mm in length. If a lens that
exceeds this size is used, the camera may be damaged
and you may not be able to attach it correctly.
• When attaching a C mount lens, attach the lens to the
camera after inserting the C mount ring (sold
separately).
Camera installation
VCB-3380P/3380P-UK
Camera screws (Shorter)
VIDEO OUT
3
220 – 240 V AC
POWER
VCB-3385P
VIDEO OUT
VS IN
Figure A
POWER
Bracket screws (Longer)
24 V AC connection
12 V DC connection
GND
AC24V
GND
AC24V
3
DC12V
DC12V
2
2
Figure 1
Figure 2
Making connections
1
Connect the camera and peripheral equipment with cables.
2
VCB-3385P only
Connect the power cable.
Secure the supplied clamping core to the power cable as
shown in Figure A.
<When using a 24 V AC adapter>
Connect 3 wire grounded cable# (use 18AWG+) to the ground
(GND) terminal as shown in Figure 1.
<When using a 12 V DC adapter>
Connect the cable as shown in Figure 2.
CAUTION
• When connecting the power cable to the camera, check that the
polarity is correct.
• To prevent fire hazard any UL listed wire rated VW-1, should be used
for the 24 V AC cable input terminal.
3
VCB-3380P/3380P-UK
Insert the power cord into the wall outlet.
The "POWER" indicator (red) lights.
VCB-3385P
Insert the power adapter plug into the wall outlet.
The "POWER" indicator (red) lights.
B B B B Camera installation
Camera attachment bracket
1
As shown in Figure B above, you can remove the camera
attachment bracket and reattach it to the camera bottom if you
want to attach the camera to the top of an object. If you remove
the camera attachment bracket, be sure to use the removed
screws when reattaching it (other screws may not fit).
CAUTION
2
When using the camera attachment stand (sold separately), select a
location that will be able to withstand the weight of the camera and stand
for many years, and fix them securely in place.
L
ADJUSTMENT, SETTINGS
The camera comes pre-adjusted and ready to install at time of
factory shipment, but you may want to make adjustments or
settings to adapt to the operating conditions or installation
environment, if necessary.
If you have trouble adjusting the camera, contact your place of
purchase or a Sanyo Authorized Service Center.
• The settings shown for switches
to
at time of factory shipment.
• Use a Phillips-head screwdriver to adjust dials
ES
GAMMA
MODE
ES
SHARP
LL
SPEED
AGC
BLC
ON
OFF
3
PHASE LEVEL
1
2
3 4 5 6 7
Camera adjustment/Settings
( = Factory default setting)
Electronic Shutter mode (ES MODE)
ON
Set the electronic shutter speed to the desired setting. (See
)
OFF
Use the standard shutter speed (1/50 sec.).
Electronic Shutter speed (ES SPEED)
When electronic shutter mode is set to ON, a combination of the
three settings can be used to set up to eight speed levels.
Shutter speed
Left
1/120
ON
1/250
ON
1/500
ON
1/1000
ON
1/2000
OFF
1/5000
OFF
1/10000
OFF
1/100000
OFF
Outline compensation (SHARP)
If object outlines appear too strongly, set to "OFF".
ON
Emphasizes object outlines.
OFF
Normal setting
Gain control (AGC)
For adjusting the sensitivity of the camera. Use this setting for
shooting in dark environments.
ON
Increased sensitivity allows shots to be taken in dark
environments.
OFF
Normal setting
Gamma compensation (GAMMA)
For adjusting the gamma compensation. Use this setting to adjust
the signal correction/contrast so that the image looks natural.
γ = 0.45
ON
OFF
No gamma compensation is applied. (γ = 1)
Backlight compensation (BLC)
For adjusting backlight compensation. Use this setting to adjust
the backlight compensation when an image is backlit.
ON
Backlight compensation
OFF
No backlight compensation is applied.
and
are the settings
Sync setting (LL)
Vertical sync disturbance may occur when a selector is used to
and
.
switch between multiple cameras connected to one monitor. To
prevent vertical sync disturbance, set to "ON".
ON
Line-Lock
• Adjust PHASE dial
VIDEO
OFF
Internal Sync
L
H
EI
DC
• Line-Lock: Synchronizes the unit with power frequency.
CAUTION
If the image disturbance doesn't disappear after adjusting the PHASE dial
( ) on the second and subsequent cameras, adjust the PHASE dial (
8
9
10
the first camera. If the problem persists, check that all the devices have
been connected with the correct power cable polarity.
Line phase (PHASE)
When sync setting ( ) is ON, use a Phillips-head screwdriver to
adjust the line phase.
Lens iris (LEVEL)
When using a DC-type auto-iris lens, adjust the LEVEL dial if the
entire image is too dark or too bright.
L (Low)
Closes the lens iris, making the entire image darker.
H (High)
Opens the lens iris, making the entire image brighter.
Lens switching
Center
Right
Set this as appropriate for the type of lens you are using.
ON
ON
EI
Electronic iris lens
ON
OFF
VIDEO
Video auto-iris lens (lens with built-in amp circuits)
OFF
ON
DC
DC-type auto-iris lens (lens without built-in amp circuits,
OFF
OFF
powered by DC power only)
ON
ON
CAUTION
ON
OFF
When using a video auto-iris lens
OFF
ON
• Turn the ALC (light control) dial on the lens barrel fully to AV (average).
OFF
OFF
• If the backlight compensation is not correct, adjust the LEVEL dial on the
lens barrel.
Flange-back adjustment
Flange back is the distance between the lens and the camera
(CCD). Follow the steps below to adjust the flange back distance,
since the image can become out of focus when you are zoomed-in
on an object.
1
Loosen the LOCK screw
with a Phillips-head
screwdriver.
2
Zoom-in with the zoom
lens, and adjust the focus
with the focus ring on the
lens.
3
Set the zoom lens to wide
angle, and adjust the focus
with the flange-back adjustment dial.
4
Repeat steps 2 and 3 to check that the focus is not lost
when switching between wide-angle and zoom, and then
tighten the LOCK screw.
to eliminate sync disturbance.
) on
(only when zoom lens is attached)
3
2
1
LOCK
4
Advertisement
