Table of Contents
Advertisement
Quick Links
SERIAL INTERFACE CARD
R
R
GAIN
GAIN
L
L
0
0
dB
dB
LINE
LINE
LINE
-10
-10
10
10
+
+
6
6
CDI-S100
SERIAL INTERFACE
MODULE
MODULE
MIC
MIC
Installation Guide
LEFT
LEFT
RIGHT
RIGHT
MUSIC
MUSIC
MUTE
MUTE
23 230
230V
2 2 2 2 2 3 23 3 3 3 3 0 30 0 0
230
230V
230V
115V
115V
T100
T100m
T100mA
T100mA
T200mA
T200mA
FUSE
FUSE
POW
POW
RATING
RATING
Advertisement
Table of Contents
Related Manuals for Cloud CDI-S100
Summary of Contents for Cloud CDI-S100
- Page 1 CDI-S100 SERIAL INTERFACE CARD SERIAL INTERFACE MODULE MODULE MUSIC MUSIC MUTE MUTE GAIN GAIN FUSE FUSE RATING RATING LINE LINE LINE LINE LINE 230V 230V 23 230 230V 2 2 2 2 2 3 23 3 3 3 3 0 30 0 0...
- Page 2 CDI-S100 Installation Guide v1.0...
-
Page 3: Table Of Contents
Introduction ..............4 Scope of this manual ................4 What’s in the box ..................4 Installation ..............4 Configuring the CDI-S100 ..............4 Mechanical fitting and internal connection ........5 CX462 jumper settings ..............6 CX462 switch settings ............... 6 CDI-S100 Remote Control ...........7 Pinout ...................... -
Page 4: Introduction
The manual also gives a general overview of the RS-232C serial control protocol used by the CDI-S100, and some examples of the most useful commands. This information should be adequate for most installations, but please note that a full description of the RS-232C protocol is beyond the scope of this manual. -
Page 5: Mechanical Fitting And Internal Connection
If the CX462 is mounted in a rack, remove it. J1 J2 J3 J1 J2 J3 If fitting the CDI-S100 to a new CX462, 300 baud unpack the CX462. In either case, place the CX462 on a flat surface, with the rear of the unit facing you. -
Page 6: Cx462 Jumper Settings
CX462 jumper settings In order for the CDI-S100 to fully control the CX462, it is necessary to correctly set some jumpers on the CX462 main PCB. These are J1 to J4, and J7 to J10. J7 - J10 MUST ALL BE IN ... -
Page 7: Cdi-S100 Remote Control
In this case, connect “Tx” The commands listed in the General Format to pin 3 on the CDI-S100, “Rx” to Pin 2 and table (page 8) are those most commonly “Gnd” to pin 5. See the following illustration required. -
Page 8: Input Selection
3C 4D 55 2C 53 41 33 2F 3E Select Line Input one above current <MU,SU/> 3C 4D 55 2C 53 55 2F 3E Select Line Input one below current <MU,SD/> 3C 4D 55 2C 53 44 2F 3E CDI-S100 Installation Guide v1.0... -
Page 9: Music Level
1 and 4. EXAMPLE COMMAND (ASCII) COMMAND (HEX) Mute mic input 1 <MI.1,M/> 3C 4D 49 2E 31 2C 4D 2F 3E Unmute mic input 3 <MI.3,O/> 3C 4D 49 2E 33 2C 4F 2F 3E CDI-S100 Installation Guide v1.0... -
Page 10: Set Master Mic Level
General Format table are always applicable. EXAMPLE COMMAND (ASCII) COMMAND (HEX) Mute mic channel <MI,M/> 3C 4D 49 2C 4D 2F 3E Unmute mic channel <MI,O/> 3C 4D 49 2C 4F 2F 3E CDI-S100 Installation Guide v1.0... -
Page 11: Appendix
100 ft. (30 m.) using unshielded cable, at 9600 baud (the most common data rate). However, the figure may be higher or lower in a particular installation. Lowering the baud rate will permit significantly longer cable runs to be used. CDI-S100 Installation Guide v1.0... - Page 12 Cloud Electronics Limited 140 Staniforth Road Sheffield S9 3HF England Tel: +44 (0)114 244 7051 Fax: +44 (0)114 242 5462 email: info@cloud.co.uk web: www.cloud.co.uk...
Need help?
Do you have a question about the CDI-S100 and is the answer not in the manual?
Questions and answers