Vaper HVLP Instruction Manual
  1. Manuals
  2. Brands
  3. Vaper Manuals
  4. Paint Sprayer
  5. HVLP
  6. Instruction manual

Vaper HVLP Instruction Manual

Hide thumbs

Advertisement

Table of Contents

HVLP Spray Guns
Instruction Manual
1

Advertisement

Table of Contents
loading

Related Manuals for Vaper HVLP

Summary of Contents for Vaper HVLP

  • Page 1 HVLP Spray Guns Instruction Manual...

  • Page 2: Safety Alert

    INTRODUCTION SAFETY ALERT It is the owner and/or operator’s responsibility to study all WARNINGS, operating, and Read and understand this entire instruction manual before maintenance instructions contained on the product label and instruction manual prior attempting to assemble, install, operate or maintain this to operation of this spray gun.
  • Page 3 IMPORTANT SAFETY RULES FOR ALL SPRAY GUNS IMPORTANT SAFETY RULES FOR ALL SPRAY GUNS SAVE THESE INSTRUCTIONS SAVE THESE INSTRUCTIONS R R e e a a d d a a n n d d u u n n d d e e r r s s t t a a n n d d a a l l l l i i n n s s t t r r u u c c t t i i o o n n s s . . Failure to follow all instructions included with this product could result in seri- ous personal injury and/or property damage.

  • Page 4: Work Area Safety

    (Transfer efficiency refers to the percentage of paint sprayed that actually adheres to the surface being painted). HVLP, electrostatic and airless paint spray guns are the only spray methods that meet the strict 65% transfer efficiency rate required by some air quality district regulations.
  • Page 5 P P R R E E S S S S U U R R E E F F E E E E D D C C I I R R C C U U L L A A T T I I N N G G H H O O O O K K U U P P Filtered, regulated the air cap, must not exceed 10 PSI. HVLP Spray guns produce a soft, low velocity For heavy production spraying, air pressure for atomiza- air source spray pattern which provides increased control while reducing paint “bounce-back”...

  • Page 6: Preparation For Spraying

    This air pressure is typically below 20 as necessary for the intended application. PSI for HVLP spray guns and between 40 to 60 PSI Failure to install appropriate water/oil removal equipment for conventional spray guns. Adjust air pressure with may result in damage to machinery or workpiece.

  • Page 7: Care And Maintenance

    PATTERN ADJUSTMENT FOR PRESSURE HOOKUPS CARE AND MAINTENANCE 1) Adjust air pressure to the spray gun according to the recommendations supplied by the spray material manufacturer. This air pressure is typically between 40 to 60 A A l l w w a a y y s s w w e e a a r r s s a a f f e e t t y y g g o o g g g g l l e e s s t t h h a a t t c c o o m m p p l l y y w w i i t t h h PSI for conventional spray guns.
  • Page 8 4) Clean gaskets with solvent soaked rag. To prevent damage, do not immerse gas- AIR NOZZLE, FLUID TIP, NEEDLE ASSEMBLY kets or spray gun in solvents as this is detrimental to the lubricants and packings. 5) After using water to clean out water based paints or materials, spray mineral spirits T T o o p p r r e e v v e e n n t t d d a a m m a a g g e e t t o o t t h h e e f f l l u u i i d d t t i i p p o o r r f f l l u u i i d d n n e e e e d d l l e e , , b b e e s s u u r r e e through the gun to prevent corrosion.

  • Page 9: Troubleshooting

    TROUBLESHOOTING TROUBLESHOOTING (Continued) Problem Encountered Possible Cause Corrective Action Problem Encountered Possible Cause Corrective Action Heavy top or bottom pattern. Horn holes plugged. Clean. Ream with non-metallic point. Excessive overspray Gun too far from work surface. Adjust to proper distance. Improper stroking Move at moderate pace, parallel to Obstruction on top or bottom of fluid tip.
  • Page 10 TOUCH UP GUN PARTS BREAKDOWN PRODUCTION GUN PARTS BREAKDOWN 19 2 0 2 9 3 0 REVERSE TYPE Item numbers in REVERSE TYPE included in 19910 Spray Gun Rebuild Kit Item numbers in included in 19909 Spray Gun Rebuild Kit Ln # Description Ln #...

  • Page 11: Application Guide

    HVLP GRAVITY FEED SPRAY GUN TIP SIZE NOTES APPLICATION GUIDE Tip Size Common Applications Touch-Up Gun For most fine finishing. Spot repairs and detail painting with primer, base coats, clear coats, single stages, low VOC. Production Guns Clear coats, base coats, water based coatings and single stages.
  • Page 12 NOTES NOTES...

  • Page 13: One-Year Limited Warranty

    ONE YEAR LIMITED WARRANTY Star Asia-USA, LLC (hereinafter “seller”) warrants to the original purchaser only, that this product will be free from defects in material or workmanship for a period of one year from date of purchase for home domestic use. W W a a r r r r a a n n t t y y P P e e r r f f o o r r m m a a n n c c e e Warranty coverage is conditioned upon purchaser furnishing seller or its authorized service center with adequate written proof of the original purchase date.

Table of Contents