1. Manuals
  2. Brands
  3. Sure Slice Manuals
  4. Kitchen Appliances
  5. SSF330PTR
  6. Operating and maintenance manual

Sure Slice SSF330PTR Operating And Maintenance Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Professional slicer CE
SSF330PTR
mod.
Operating and Maintenance Manual
SERVICE CENTRE
AUTHORISED DEALER
28
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SSF330PTR and is the answer not in the manual?

Questions and answers

Related Manuals for Sure Slice SSF330PTR

Summary of Contents for Sure Slice SSF330PTR

  • Page 1 Professional slicer CE SSF330PTR mod. Operating and Maintenance Manual SERVICE CENTRE AUTHORISED DEALER...

  • Page 3: Chap. 8 - Dismantling

    INTRODUCTION CHAP. 8 - DISMANTLING This manual has been re-presented to provide the Client with all the information on 8.1 - OUT OF SERVICE the machine and its safety regulations, and also the use and maintenance instructions If for some reason it is decided to put the machine out of service, make sure that which permit using the machine in the best way and maintaining its efficiency it cannot be used by anyone: detach or cut the electrical connections.

  • Page 4: Chap. 7 - Maintenance

    CHAP. 6 - ROUTINE CLEANING page 22 CHAP. 7 - MAINTENANCE - GENERALITIES - CLEANING THE MACHINE 7.1 - GENERALITIES 6.2.1 - Cleaning the goods holder plate Before carrying out any maintenance operations it is necessary to: 6.2.2 - Cleaning the sliceguard Cleaning the blade, blade cover and ring guard a) disconnect the feed plug from the electrical network to completely isolate 6.2.3 -...
  • Page 5 be cleaned in a dishwasher. CHAP. 1 - RECEIVING THE MACHINE WARNING: there is a split in the blade remover to allow the remover to fit onto the blade, therefore once the 1.1 - PACKAGE blade and remover are removed from the slicer GREAT CARE must be The slicer is shipped in a package which consists of (Fig.
  • Page 6 having taken off the trolley, the goods holder plate can be carefully cleaned with warm water, the equipped deter- Do not expose the package to humidity gent or neutral detergent (pH 7). or rain (Fig. n°4). Fig. n°48 Fig. n°4 6.2.2 - Cleaning the sliceguard (Fig.

  • Page 7: Chap. 2 - Installation

    7. press the 2 push-buttons (2 and 3) the documents, make a precise report on the damage to the machine. Do not contemporaneously for 3/4 sec. and overturn the package!! When transporting it make sure that it is firmly held release them in the same instant by the four corners (keeping it parallel to the floor).

  • Page 8: Sharpening The Blade

    2.2 - POSITIONING 8. Carry out resharpening the blade as soon as the cut product has a threaded or rough surface, therefore thecutting effort increases (chapter 5.3). Position the pallet, with the slicer, on a flat surface and take off (a) the cap 5.3 - SHARPENING THE BLADE from the slicer (Fig.

  • Page 9: Loading And Cutting The Product

    5.2 - LOADING AND CUTTING THE PRODUCT 2.3 - ELECTRICAL CONNECTION WARNING: The goods to be cut are loaded on the hopper only with the gradua- Check that the data reported on the ted hand grip at “0” and the motor stopped, being careful with the blade and the technical-part number plate (Fig.

  • Page 10: Operational Check

    2.3.4 - Slicer with 230 V. three-phase motor CHAP. 5 - MACHINE USE The slicer is equipped with a feeding cable with a section area of 5x1mm²; length 1.5m and a blue 15A 3F + T CEI plug. 5.1 - OPERATIONAL CHECK Connect the slicer 230 V.
  • Page 11 TAB. n°1 - DIMENSION MEASUREMENTS AND TECHNICAL FEATURES 2.4.1 - 115 V. tension selection MODEL U.m. SSF330PTR Blade diameter Motor Watt/Hp 275/0,37 Cut thickness 2.4.2 - Single-phase 230 V. tension selection Run of carriage 300x270 Hopper 468x338 OUTPUT DIAGRAM CxDxE...
  • Page 12 2.5 - PRELIMINARY CHECK - A relay in the control circuit, that re- quires the machine to start up again Before testing make sure the goods in case of an accidental loss of electri- holder plate is well-blocked, after which city (Fig.

  • Page 13: Safety Devices Installed On The Machine

     4.2 - SAFETY DEVICES INSTALLED ON THE MACHINE The slicer must only be used by trained personnel who know the 4.2.1 - Mechanical safety safety norms contained in this manual As far as mechanical safety is concerned, the slicer described in this manual perfectly.

  • Page 14: Construction Features

     Do not pull the slicer or the feeding cable LEGEND: (Fig. n°29) to unplug it. 1 - Cap 14 - Ring  Regularly check the state of the fee- 2 - Bladeguard tie rod hand grip 15 - Cap hand grip ding cable;...

Table of Contents