Advertisement
BRIEF OF PRODUCT
* Sensor (CCD) Adopt SONY 1/3" CCD Sensor.
* Auto Gain Control (AGC)
Built-in auto gain control (AGC) circuit. The color camera
can get high definition picture in low Lux condition.
* Scanning Mode: NTSC or PAL mode.
* On Screen Display(OSD)
Gives you an overview of the selection of controls available for
easy setting
* Digital Wide Dynamic Range(DWDR) Captures a clean, high
resolution image, even with strong back light.
* OSD SETTING
LENS
MANUAL/DC/VIDEO
AUTO,1/50,1/250,1/500,1/2000,1/5000,1/10000,
SHUTTER
1/100000,×2,×4,×8,×16,×32,×64,×128,×256
BRIGHTNESS
LOW/MIDDLE/HIGH/OFF
AGC
EXPOSURE
SENSE UP
BLC
OFF/INDOOR/OUTDOOR
D-WDR
RETURN
WHITE BAR
ATW/AWB/AWC/MANUAL/INDOOR/OUTDOOR
DAY NIGHT
AUTO/COLOR/B/W
3DNR
ON/OFF
CAM TITLE
D-EFFECT
OSD SET
RS485
MOTION
SPECIAL
PRIVACY
SYNC
LANGUAGE
CHINESE/ENGLISH/JAPANESE
RETURN
SHARPNESS
BLUE
AD JUST
RED
RETURN
FACTORY RESET
RESET
RETURN
EXIT
CONNECTING
KEY BOARD
UP
LEFT
DOWN
0－100
2X to 128X
TROUBLE AND SOLUTION
OFF/BLC/HSBLC
1. No Picture after providing power
. May be the power supply voltage abnormity, please check the power
supply voltage and pole whether exactitude.
. Please check all the connecting cable and monitors whether be connected
ON/OFF
correctly or not.
FREEZE ON/OFF
MIRROR
2. The picture level direction have flowing interference ripples
D-ZOOM
. May be caused by the power supply AC ripples, it need filter the wave of the
GAMMA
power supply.
NEG.IMAGE
. Check the monitor and peripheral equipments used.
RETURN
CAM ID
3. The picture background color changes continuously
ID DISPLAY
. The fluorescent lamp's electromagnetic field cause color roll. This is proper
BAUDRATE
phenomenon of the cameras.
ON/OFF
. Reduce the fluorescent lamp numbers or increase the distance between the
OFF
camera and the fluorescent lamps can improve it.
AREA SELECT
. Use power supply external sync. camera can solve it.
AREA DISPLAY
LEFT/RIGHT
4. The picture smear too mass
WIDTH
. The power supply's voltage unstable.
Top/Bottom
. Connecting cables not connect correctly or have high impedance.
Height
Color
INT
Notes：
●The power supply must through safe attestation. Its output voltage,
0-31
current, voltage polarity and operating temperature must match the
0-100
camera's requirement.
0-100
●When using the camera in the thunderbolt condition,please note to
mount Anti-thunder device or put off the power supply plug and cable.
●In order to capture high quality pictures, the power supply's cable and
video output cable should not be too long.
Monitor
MTX600DIR
MENU
Link wire rule：
RIGHT
Video
Power
PRESS
DC12V Power Supply
INTRODUCTION
Congratulations on your purchase of this product.
This User Guide suits
MTX600DIR
adopt the latest SONY technical of sensor and driver. The
Video
most attractive characteristics are small and easy hidden,
suits the elevator and corridor. In addition, it owns the
characters of high definition and stability, strong anti-
jamming, rich and real color. Fixing and using this model
are convenient too. It is very good for you to apply to your
DC12V
CCTV system.
Please read this instruction manual carefully to
ensure proper use of the product.
To prevent fire or shock hazarded. Do not expose the unit
to rain or moisture.
The symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
Instructions in the literature accompanying the appliance.
The symbol is intended to alert the user to the presence of
uninsulated 'dangerous voltage' within the product's
enclosure that may be of sufficient Magnitude to constitute
a risk of electric shock to persons.
RISK OF ELECTRIC. DO NOT OPEN
CAUTION:
SHOCK
DO NOT REMOVE COVER OR BACK NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
CAUTION:
TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS, DO NOT USE OTHER THAN
SPECIFIED POWER SOURCE.
Note:
● Please note the camera's operating temperature and its using
environment requirement. Avoid using the camera at too high or
too low temperatures. The operating temperature is –10~+45℃.
(Recommendatory operating temperature is –5~+40℃.)
● Never make the camera face the sun or bright object.
Otherwise, it will damage the CCD.
● Do not mount the camera near by the radiator or heater.
series product. We
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
Advertisement
