Chassis Electrical Parts List - Sanyo P46841-03 Service Manual

CAUTION: To Protect against electrical shock and for continued product safety, refer to SAFETY PRECAUTIONS
and PRODUCT SAFETY NOTICE on Page 2
PRODUCT SAFETY SHOULD BE CONSIDERED WHEN A REPLACEMENT IS MADE IN ANY AREA OF A RECEIVER.
COMPONENTS INDICATED BY A
COMPONENTS IN WHICH SAFETY CAN BE OF SPECIAL SIGNIFICANCE. IT IS PARTICULARLY RECOMMENDED
THAT ONLY PARTS DESIGNATED ON THE FOLLOWING PARTS LIST BE USED FOR COMPONENT REPLACE-
MENT DESIGNATED BY A
BE MADE FOR REPLACEMENT ITEMS DESIGNATED BY A
Note: Schematic part location numbers may not always match with the part descriptions.
The part descriptions are correct and should be used.
Schematic
Part No.
Location
CAPACITORS
NOTES:
Read Description of the Capacitor as follows:
(Example)
CERAMIC 100P K 50V
Tolerance Symbols:
Less than 10pF
A : Not specified
D : ±0.5pF
G : ±2pF
R : ±0.25-0pF
More than 10pF
A : Not specified
D : ±0.5%
H : ±3%
L : ±15%
P : +100-0%
U : +75-10%
X : +40-20%
Rated value: P=pico tarad, U=micro tarad
Material:
CERAMIC . . . . . . .
MT-PAPER. . . . . . .
POLYESTER . . . . .
MT-POLYEST . . . .
POLYPRO . . . . . . .
MT-POLYPRO . . . .
COMPO FILM . . . .
MT-COMPO. . . . . .
STYRENE . . . . . . .
TA-SOLID . . . . . . .
AL-SOLID . . . . . . .
ELECT . . . . . . . . . .
NP-ELECT . . . . . . .
OS-SOLID . . . . . . .

CHASSIS ELECTRICAL PARTS LIST

PRODUCT SAFETY NOTICE
IN THIS PARTS LIST AND THE SCHEMATIC DIAGRAM DESIGNATE
. NO DEVIATIONS FROM RESISTANCE, WATTAGE, AND VOLTAGE RATINGS MAY
Description
Rated Voltage
B : ±0.1pF C : ±0.25pF
E : +0-1pF F : ±1pF
H : +0.1-0pF L : +0-0.1pF
S: ±0.25-0pF
B : ±0.1% C : ±0.25%
F : ±1% G : ±2%
J : ±5% K : ±10%
M : ±20% N : ±30%
Q : +30-10% T : +50-10%
V : +20-10% W : +100-10%
Y : +150-10% Z : +80-20%
Ceramic
Metallized Paper
Polyester
Metallized Polyester
Polypropylene
Metallized Polypropylene
Composite Film
Metallized Composite
Styrene
Tantalum Solid
Aluminum Solid
Electrolytic
Non-polarised Electrolytic
Alluminum Solid with Organic
Semiconductive Electrolytic
.
Schematic
Part No.
Location
NOTES:
Read Description of the Resistor as follows:
(Example)
CARBON 4.7K J
Rated value, ohms:
K...1,000 M...1,000,000
Material:
CARBON . . . . . . . .
MT-FILM . . . . . . . .
OXIDE-MT . . . . . . .
SOLID . . . . . . . . . .
MT-GLAZE . . . . . .
WIRE WOUND . . .
CERAMIC RES . . .
FUSIBLE RES . . . .
– 9 –
Description
RESISTORS
A 1/4W
Rated Wattage
Performance Symbols:
A...General B..Non-flammable
Z...Low noise
Other...Temperature coefficient
Tolerance Symbols:
A...0.05% B...0.1% C...25%
D...0.5% F...1% G...2%
J...5% K...10% M...20%
P...+5-15%
Carbon
Metal Film
Oxide Metal Film
Composition
Metal Glaze
Wire wound
Ceramic
Fusible