PRO-HDMI-CAT-PLG HDMI 1.3 over Single CAT5 Direct Plug-in Extender User Manual Made in Taiwan rev.1008 103 Quality Circle, Suite 210 | Huntsville, Alabama 35806 | Tel: (256) 726-9222 | Fax: (256) 726-9268 | Email: service@pesa.com...
PESA Switching Systems, Inc., (PESA) warrants this equipment against defective workmanship or materials for a period of one (1) year from date of shipment. The sole warranty responsibility of PESA, shall be to replace or repair product proved to be defective. During the warranty period, defective parts will be replaced at no charge.
Page 3
INTRODUCTION The PRO-HDMI-CAT-PLG HDMI 1.3 over Single CAT5 Direct Plug-in Extender boosts up the audio/video transmission distance up to 25m in HDTV 1080i format, or 15m in HDTV 1080p format. With only one cost effective solid category cable, users can readily extend HDTV sources from DVD player, Blu-ray Disc player, PS3, PC, and any other kinds of sources compliant with TMDS to distant display monitors including HDMI or DVI enabled TV sets or LCD PC monitors.
5V 2A DC None Power consumption 1 Watt (max) Operation temperature 32-104°F / 0-40°C Storage temperature -4-140°F / -20-60°C Relative humidity 20-90% RH (no condensation) 1x PRO-HDMI-CAT-PLG 1x 5V power supply unit Package Contents 1x User manual ~ 2 ~...
PANEL DESCRIPTION Transmitting unit PRO-HDMI-CAT-PLG-TX Input Panel MODE SET: 0 – Supported up to 1080p 36-bit video and up to 7.1ch audio output. 1 – Supported up to 1080p 36-bit video and stereo audio output. 2 – Supported up to 1080p 24-bit video and up to 7.1ch audio output.
Page 6
Receiving unit PRO-HDMI-CAT-PLG-RX RJ45: Plug in a Cat-5/5e/6 cable and link it to the RJ45 port HDMI OUT CAT 5/6 on the transmitting unit PRO-HDMI-CAT-PLG-TX. HDMI: Connect to a HDMI display or projector directly. ~ 4 ~...
INSTALLATION 1. Connect a HDMI source to the transmitting unit PRO-HDMI-CAT-PLG-TX. 2. Connect a HDMI display or projector to the receiving unit PRO-HDMI-CAT-PLG-RX. 3. Connect a Cat-5/5e/6 cable between the transmitting and receiving units. 4. Make sure this Cat-5/5e/6 cable is tightly connected and not loose.
If you need to get 1080p with 7.1ch audio output, dial the rotary arrow counterclockwise [ ] from Mode 1 Mode 0. If you cannot get the audio/video out normally, please refer to EDID LEARNING section to learn the EDID from this intended HDMI display for PRO-HDMI-CAT-PLG-TX. ~ 6 ~...
PRO-HDMI-CAT-PLG-TX counterclockwise [ ] to 7. Step 3 – Connect the HDMI display to “HDMI IN” on the PRO-HDMI-CAT-PLG-TX transmitter with a HDMI cable. The LED on the RJ45 connector of PRO-HDMI-CAT-PLG-TX transmitter will dim and light again, which indicates the EDID learning procedure is complete.
Page 11
NOTICE 1. All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP cable and ASTRODESIGN Video Signal Generator VG-859C. 2. The transmission length is largely affected by the type of Category cables, the type of HDMI sources, and the type of HDMI display.
Page 12
PRO-HDMI-CAT-PLG HDMI 1.3 over Single CAT5 Direct Plug-in Extender PESA Switching Systems, Inc. 103 Quality Circle, Suite 210 Huntsville, Alabama 35806 Tel: +1 (256) 726-9222 Fax: +1 (256) 726-9268 Email: service@pesa.com...