Micro 6888 Installation Manual

6. ANTI HI-JACK MODE

There are three different ways to activate Anti Hi-Jack (AHJ).
1. By Ignition (Programmable Feature #7, Default setting is OFF)
When Programmable Feature #7 is ON, and the ignition is turned
on, the alarm will enter AHJ mode. The siren will chirp three times
and the LED will flash fast.
Note: If programmable feature #7 hi-jack through ignition is enabled
(ON) you must exit hi-jack mode using the valet button before
entering programming mode, see section 4 to enter programming
mode. Do not turn ignition off, leave ignition on, then press valet
button 5 times to enter programming mode.
2. By Door (Programmable Feature #8, Default setting is OFF)
When Programmable Feature #8 is ON, and when the Ignition is ON
AND the driver door is opened then closed, alarm will enter AHJ
mode. The siren will chirp three times and the LED will flash fast.
3. By Remote Control (Programmable Feature #9, Default setting is OFF)
When Programmable Feature #9 is ON and Ignition ON, Press and
hold PANIC and AUX together for 2 seconds – alarm will enter AHJ
mode. Siren will chirp three times and LED will flash fast.
NOTE: All three features can be set to ON.
ANTI HI-JACK MODE ACTIVATED STATUS
• From 0-60 sec LED will flash quickly.
• From 61-70 sec LED will flash quickly, siren chirps, and the
parking light will flash.
• From 71-80 sec LED will flash quickly, siren chirps, parking light
will flash, and ignition cut output constantly.
• After 81 sec LED will flash quickly, siren chirps, parking light will
flash and ignition cut output constantly.
EXIT ANTI HI-JACK MODE
• From 00-60 sec, Turn on the ignition, then press and hold UNLOCK
button for 2 sec. The system will be in disarm mode.
• After 60 sec, Turn on ignition, then press override switch for 1 sec.
The system will be in disarm mode.
8
#6888
#6888
INSTALLATION MANuAL

REMOTE OPERATION GUIDE

#6888
#6888 REMOTE OPERATION GUIDE
REMOTE OPERATION GUIDE
#6888
LOCK BUTTON
REMOTE OPERATION GUIDE
#6888
LOCK BUTTON
REMOTE OPERATION GUIDE
• Press and release the LOCK button to ARM ALARM
LOCK BUTTON
and LOCK DOORS
• Press and release the LOCK button to ARM ALARM
• Press and release the LOCK button to LOCK DOORS
and LOCK DOORS
• Press and release the LOCK button to ARM ALARM LOCK BUTTON
• Press and release LOCK button and press it again for
and LOCK DOORS
• Press and release the LOCK button to LOCK DOORS
LOCK BUTTON
2 SECONDS to BYBASS SHOCK SENSOR and ARM
• Press and release the LOCK button to LOCK DOORS • Press and release the LOCK button to ARM ALARM
• Press and release LOCK button and press it again for
ALARM (Use this to bypass shock sensor)
and LOCK DOORS
2 SECONDS to BYBASS SHOCK SENSOR and ARM
• Press and release LOCK button and press it again for • Press and release the LOCK button to ARM ALARM
ALARM (Use this to bypass shock sensor)
• Press and release the LOCK button to LOCK DOORS 2 SECONDS to BYBASS SHOCK SENSOR and ARM and LOCK DOORS
UNLOCK BUTTON
ALARM (Use this to bypass shock sensor)
• Press and release LOCK button and press it again for • Press and release the LOCK button to LOCK DOORS
UNLOCK BUTTON
2 SECONDS to BYBASS SHOCK SENSOR and ARM
• Press and release LOCK button and press it again for
• Press and release the UNLOCK button to DISARM
UNLOCK BUTTON
ALARM (Use this to bypass shock sensor)
2 SECONDS to BYBASS SHOCK SENSOR and ARM
ALARM and UNLOCK DOORS
• Press and release the UNLOCK button to DISARM
ALARM (Use this to bypass shock sensor)
• Press and release the UNLOCK button to STOP
ALARM and UNLOCK DOORS
• Press and release the UNLOCK button to DISARM UNLOCK BUTTON
ALARM TRIGGER
ALARM and UNLOCK DOORS
• Press and release the UNLOCK button to STOP
UNLOCK BUTTON
• Press and release the UNLOCK button to UNLOCK
• Press and release the UNLOCK button to DISARM ALARM TRIGGER
• Press and release the UNLOCK button to STOP
DOOR
ALARM TRIGGER ALARM and UNLOCK DOORS
• Press and release the UNLOCK button to UNLOCK
• Press and release the UNLOCK button to DISARM
• Press and Hold the UNLOCK button for 2 SECONDS
• Press and release the UNLOCK button to STOP • Press and release the UNLOCK button to UNLOCK DOOR ALARM and UNLOCK DOORS
to switch ALARM to KEYLESS basic mode.
ALARM TRIGGER DOOR
• Press and Hold the UNLOCK button for 2 SECONDS
• Press and release the UNLOCK button to STOP
to switch ALARM to KEYLESS basic mode.
• Press and release the UNLOCK button to UNLOCK • Press and Hold the UNLOCK button for 2 SECONDS ALARM TRIGGER
PANIC BUTTON
DOOR to switch ALARM to KEYLESS basic mode.
• Press and release the UNLOCK button to UNLOCK
PANIC BUTTON
• Press and Hold the UNLOCK button for 2 SECONDS DOOR
• Press and hold the PANIC but-
PANIC BUTTON
to switch ALARM to KEYLESS basic mode.
• Press and Hold the UNLOCK button for 2 SECONDS
ton for 2 SECONDS to TRIGGER
• Press and hold the PANIC but-
to switch ALARM to KEYLESS basic mode.
HORN / SIREN
PANIC BUTTON
• Press and hold the PANIC but- ton for 2 SECONDS to TRIGGER
HORN / SIREN
ton for 2 SECONDS to TRIGGER
PANIC BUTTON
HORN / SIREN
• Press and hold the PANIC but-
AUX BUTTON
ton for 2 SECONDS to TRIGGER
• Press and hold the PANIC but-
HORN / SIREN AUX BUTTON
ton for 2 SECONDS to TRIGGER
• Press and release the AUX button for TRUNK
AUX BUTTON
HORN / SIREN
RELEASE
• Press and release the AUX button for TRUNK
• Press and hold the AUX button for 2 SECONDS for
RELEASE
• Press and release the AUX button for TRUNK AUX BUTTON
SILENT ARMING and Lock Doors
RELEASE
• Press and hold the AUX button for 2 SECONDS for
AUX BUTTON
• Press and hold the AUX button for 2 SECONDS for
SILENT ARMING and Lock Doors
• Press and release the AUX button for TRUNK • Press and hold the AUX button for 2 SECONDS for
SILENT DISARMING and Unlock Doors
RELEASE SILENT ARMING and Lock Doors
• Press and hold the AUX button for 2 SECONDS for
• Press and release the AUX button for TRUNK
• Press and hold the AUX button for 2 SECONDS for SILENT DISARMING and Unlock Doors
• Press and hold the AUX button for 2 SECONDS for RELEASE
VALET OVERRIDE SWITCH OPERATION
SILENT ARMING and Lock Doors SILENT DISARMING and Unlock Doors
• Press and hold the AUX button for 2 SECONDS for
• Press and hold the AUX button for 2 SECONDS for SILENT ARMING and Lock Doors
VALET OVERRIDE SWITCH OPERATION
1. Stopping horn/siren: Turn ignition on, press and hold valet switch until horn/siren stops.
USED FOR: SILENT DISARMING and Unlock Doors
VALET OVERRIDE SWITCH OPERATION • Press and hold the AUX button for 2 SECONDS for
2. To enter/exit keyless basic mode (LED steady on): Ignition on and hold valet switch for 5 seconds.
SILENT DISARMING and Unlock Doors
1. Stopping horn/siren: Turn ignition on, press and hold valet switch until horn/siren stops.
USED FOR:
3. Use to program remotes: Turn ignition on, press and release valet switch 5 times, press lock buttons on
2. To enter/exit keyless basic mode (LED steady on): Ignition on and hold valet switch for 5 seconds.
1. Stopping horn/siren: Turn ignition on, press and hold valet switch until horn/siren stops. VALET OVERRIDE SWITCH OPERATION
USED FOR:
each remote to be programmed, turn ignition off. Up to 4 remotes may be programmed.
3. Use to program remotes: Turn ignition on, press and release valet switch 5 times, press lock buttons on
2. To enter/exit keyless basic mode (LED steady on): Ignition on and hold valet switch for 5 seconds.
VALET OVERRIDE SWITCH OPERATION
Most Common Locations (Ask installer where it is located.) each remote to be programmed, turn ignition off. Up to 4 remotes may be programmed.
3. Use to program remotes: Turn ignition on, press and release valet switch 5 times, press lock buttons on
1. Stopping horn/siren: Turn ignition on, press and hold valet switch until horn/siren stops.
USED FOR:
• Inside glove compartment, driver's kick panel, behind the
each remote to be programmed, turn ignition off. Up to 4 remotes may be programmed.
2. To enter/exit keyless basic mode (LED steady on): Ignition on and hold valet switch for 5 seconds.
Most Common Locations (Ask installer where it is located.)
USED FOR: fuse panel access door, underneath 1. Stopping horn/siren: Turn ignition on, press and hold valet switch until horn/siren stops.
• Inside glove compartment, driver's kick panel, behind the 3. Use to program remotes: Turn ignition on, press and release valet switch 5 times, press lock buttons on
Most Common Locations (Ask installer where it is located.)
the dashboard in front of the driver. 2. To enter/exit keyless basic mode (LED steady on): Ignition on and hold valet switch for 5 seconds.
fuse panel access door, underneath each remote to be programmed, turn ignition off. Up to 4 remotes may be programmed.
• Inside glove compartment, driver's kick panel, behind the
3. Use to program remotes: Turn ignition on, press and release valet switch 5 times, press lock buttons on
the dashboard in front of the driver.
fuse panel access door, underneath
each remote to be programmed, turn ignition off. Up to 4 remotes may be programmed.

REPLACEMENT REMOTE PART NUMBER: #REMOTE-6888

Most Common Locations (Ask installer where it is located.)
the dashboard in front of the driver.
THIS IS ONLY A GUIDE
• Inside glove compartment, driver's kick panel, behind the
Most Common Locations (Ask installer where it is located.)
REPLACEMENT REMOTE PART NUMBER: #REMOTE-6888
fuse panel access door, underneath
The button operations shown are a general guide. Consult with the dealer that installed your keyless entry to confi rm these remote functions.
• Inside glove compartment, driver's kick panel, behind the
THIS IS ONLY A GUIDE
REPLACEMENT REMOTE PART NUMBER: #REMOTE-6888
©2011 Micro Alarm Systems, Inc. • 6888-Op-oct2011.indd
the dashboard in front of the driver.
fuse panel access door, underneath
THIS IS ONLY A GUIDE
The button operations shown are a general guide. Consult with the dealer that installed your keyless entry to confi rm these remote functions.
the dashboard in front of the driver. ©2011 Micro Alarm Systems, Inc. • 6888-Op-oct2011.indd
The button operations shown are a general guide. Consult with the dealer that installed your keyless entry to confi rm these remote functions.
REPLACEMENT REMOTE PART NUMBER: #REMOTE-6888
©2011 Micro Alarm Systems, Inc. • 6888-Op-oct2011.indd
THIS IS ONLY A GUIDE
REPLACEMENT REMOTE PART NUMBER: #REMOTE-6888
The button operations shown are a general guide. Consult with the dealer that installed your keyless entry to confi rm these remote functions. THIS IS ONLY A GUIDE
REPLACEMENT REMOTE PART NUMBER: #REMOTE-6888
©2011 Micro Alarm Systems, Inc. • 6888-Op-oct2011.indd
The button operations shown are a general guide. Consult with the dealer that installed your keyless entry to confi rm these remote functions.
©2011 Micro Alarm Systems, Inc. • 6888-Op-oct2011.indd
THIS IS ONLY A GUIDE
These instructions are a general guideline of possible applications. Specifications may change dependent
upon vehicle. Always review the vehicle's service manual and wiring diagram when performing an
installation. Manufacturer does not assume any responsibility for damages to property or persons
which may occur due to incorrect applications or product failure. Not responsible for typographical
errors. Specifications are subject to change without notice.
Warranty void if not installed by authorized dealer.
Specification and date are subject to change or withdrawal without notice.
© 2011 Micro Alarm, Inc. • 6888-Inst-oct2011.indd
Ignition must be OFF
Ignition must be OFF
During Valet Mode
Ignition must be OFF
Ignition must be OFF
During Valet Mode
Ignition must be OFF During Valet Mode
Ignition must be OFF
Ignition must be OFF Ignition must be OFF
During Valet Mode
Ignition must be OFF During Valet Mode
Ignition must be OFF
Alarm must be ARMED and
Ignition OFF
Alarm must be ARMED and
When siren / horn is Sounding
Ignition OFF
Alarm must be ARMED and
Ignition OFF
When siren / horn is Sounding
During Driving or Valet Mode
Alarm must be ARMED and
When siren / horn is Sounding
Ignition OFF
During Driving or Valet Mode
Alarm must be ARMED and
Alarm must be DISARMED
When siren / horn is Sounding During Driving or Valet Mode Ignition OFF
and Ignition ON.
Alarm must be DISARMED
When siren / horn is Sounding
and Ignition ON.
Alarm must be DISARMED During Driving or Valet Mode
2nd AUXILIARY
LOCK
and Ignition ON.
During Driving or Valet Mode
LOCK 2nd AUXILIARY
Alarm must be DISARMED
• Press LOCK and PANIC buttons
PRESS
2nd AUXILIARY
LOCK
TOGETHER and Ignition ON.
Alarm must be DISARMED
together to get AUX2 Output.
• Press LOCK and PANIC buttons
PRESS
and Ignition ON.
TOGETHER
Note: Contact installer to make sure this
LOCK • Press LOCK and PANIC buttons 2nd AUXILIARY together to get AUX2 Output.
PANIC PRESS
TOGETHER
option is enabled.
together to get AUX2 Output.
2nd AUXILIARY
LOCK
Note: Contact installer to make sure this
PANIC
• Press LOCK and PANIC buttons option is enabled.
PRESS
Note: Contact installer to make sure this
PANIC
TOGETHER
option is enabled. together to get AUX2 Output.
• Press LOCK and PANIC buttons
PRESS
TOGETHER
together to get AUX2 Output.
Note: Contact installer to make sure this
PANIC
option is enabled.
Note: Contact installer to make sure this
PANIC
option is enabled.
Alarm must be DISARMED
and ignition OFF
Alarm must be DISARMED
Alarm must be ARMED and
and ignition OFF
Alarm must be DISARMED
ignition OFF
and ignition OFF
Alarm must be ARMED and
Alarm must be DISARMED ignition OFF
Alarm must be ARMED and
and ignition OFF ignition OFF
Alarm must be DISARMED
Alarm must be ARMED and and ignition OFF
ignition OFF
Alarm must be ARMED and
ignition OFF