KIAM Sherwood 52 Instruction Manual

5in1 petrol multifunction garden tool petrol strimmer, brush cutter, hedge trimmer, pruner

Advertisement

Kiam
Power Products
Kiam Sherwood Multi-Tool
Petrol Strimmer, Brush Cutter, Hedge Trimmer, Pruner
Instructions Manual
Read instructions manual before use!
Equipmart Ltd
Kiam House
Birchill Road
Knowsley Ind. Park North
Merseyside
L33 7TD
United Kingdom
T: 0044 151 548 5500
© Equipmart Ltd
F: 0044 151 548 5599
www.kiamproducts.co.uk

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sherwood 52 and is the answer not in the manual?

Questions and answers

Summary of Contents for KIAM Sherwood 52

  • Page 1 Kiam Power Products Kiam Sherwood Multi-Tool Petrol Strimmer, Brush Cutter, Hedge Trimmer, Pruner Instructions Manual Read instructions manual before use! Equipmart Ltd Kiam House Birchill Road Knowsley Ind. Park North Merseyside L33 7TD United Kingdom T: 0044 151 548 5500 ©...
  • Page 2: Table Of Contents

    Contents Specification ................Parts Location ................Warning labels on the machine ..........Symbols on the machine ............For safe operation ..............Setup ..................Fuel ................... Operation .................. Maintenance ................Storage ..................Disposal ..................Troubleshoot Guide ..............Spare parts ................Warranty ................... SAFETY FIRST Instructions will contain warnings within this manual, they will be marked with a symbol concern-...
  • Page 3: Specification

    1. Specification Description 5in1 Petrol Multifunction Garden Tool Model / Type Sherwood 52 1 Adjustable carrying strap with shoulder pad 1 Mixing tank (600ml) Accessories 1 Tool Kit Engine Engine model TT1E44F-5 Engine type 2-Stroke - vertical single cylinder Bore x Stroke 44 x 34.6mm...
  • Page 4: Parts Location

    2. Parts location 1. Loop handle 13. Choke lever 2. Suspension point 14. Air cleaner cover 3. Stop switch 15. Cutting guard 4. Throttle cable 16. Angle transmisson 5. Throttle trigger 17. Cutting line head 6. Throttle set button 18. Blade 7.
  • Page 5: For Safe Operation

    5. For safe operation gases contain dangerous carbon Read this manual carefully until monoxide. you completely understand and 2. Never use the product, follow all safety and operating a. when the ground is slippery instructions. Also know how to or when you can’t maintain a stop the machine quickly in the steady posture.
  • Page 6 Kiam dealer. look around or otherwise check for the presence and locations of other people working so as to...
  • Page 7 Kiam dealer. Under no circumstances should you ever take apart the product or alter it in any way. Doing so...
  • Page 8 5. For safe operation KICKBACK SAFETY PRECAUTIONS FOR PRUNER USERS WARNING WARNING • Kickback may occur when the nose • Make sure the chain and sprocket are or tip of the guide bar touches an correctly adjusted before operating the object or when the wood closes in pruner.
  • Page 9: Setup

    6. Setup MOUNTING ENGINE INSTALLING HANDLE About 19 inches (48 cm) Push the shaft tube towards the clutch housing and rotate the drive by hand to check that it is engaged • Mount the handle to the shaft tube and suspension point with the gears.
  • Page 10 6. Setup HARNESS QUICK RELEASE ATTACHING THE PRUNER The harness is equipped with a quick release mecha- (1) Main pipe nism to help release the machine from the harness in (2) Transmission emergency situations. WARNING (3) Screw hole (4) Fastening bolt Make sure to check the quick release mechanism is working correctly BEFORE operating the machine.
  • Page 11 6. Setup Adjust the chain tension by turning the tensioner ATTACHING THE HEDGE TRIMMER screw until the bottom of the chain touches the bottom of the guide bar. (1) Drive shaft (2) Trimming mechanism (3) Screw hole (4) Screw (5) Fastening bolt Remove the screw from the end of the hedge (1) Chain tension adjusting screw trimmer.
  • Page 12: Fuel

    3. Fasten the fuel cap securely and wipe up any fuel • The engines are lubricated by oil specially formulated spillage around the unit. for air-cooled 2-stroke petrol engine use. If Kiam 2-stroke oil is not available, use a red semi-synthetic 2-stroke oil. 1. Select clear flat ground for fueling.
  • Page 13: Operation

    8. Operation STARTING THE ENGINE 6. While holding the unit firmly, pull out the starter rope quickly until engine fires. WARNING The cutting head will start rotating upon the engine starting. Pour fuel into the fuel tank and tighten the cap securely.
  • Page 14 8. Operation You can avoid thrown debris by sweeping from your ADJUSTING THE THROTTLE CABLE left to the right. The normal play is 1-2mm when measured at the Use a slow movements to cut heavy growth. The carburetor end. Readjust with the cable adjuster if rate of the cutting motion will depend on the material required.
  • Page 15 8. Operation Use the shoulder strap with the unit hanging to your CUTTING METHOD right side. Adjust the strap length so the cutting head becomes parallel to the ground. Use the left side of the blade for cutting. Guide the blade from your right to the left with it tilted at a slight angle to your left.
  • Page 16 8. Operation HEDGE TRIMMER PRUNER WARNING CHECKING OIL SUPPLY The hedge trimmer has extremely sharp blades and After starting the engine, run the chain at medium if used incorrectly they can be extremely danger- speed and see if chain oil is scattered off as shown in ous.
  • Page 17: Maintenance

    9. Maintenance Every Every Every Before System/components Procedure Note hours hours hours after after after fuel leaks, fuel spillage wipe out fuel tank, air filter, fuel filter inspect/clean replace, if necessary idle adjusting screw idling speed (p. 22) if necessary spark plug plug gap replace, if necessary...
  • Page 18 9. Maintenance IMPORTANT REFILLING STRIMMING LINE If waste gets stuck and causes blockage around the 1. For replacement line, use a diameter of 2.4mm(.095in). intake air cooling vent or between the cylinder fins, The spool is capable for a line upto 6m(20ft) on the it may cause the engine to overheat which in turn 10cm(4”) head.
  • Page 19 9. Maintenance BLADES OILING PORT • When refilling the tank or resting, it is often a good Dismount the guide bar and check the oiling port for idea to use the time to oil the cutting blades. blockages. • If a gap exists between the upper and lower blades, follow the procedure below to adjust them so that they (1) Oiling port fit more closely together.
  • Page 20: Storage

    9. Maintenance CHAIN Make sure every chain link has the same length and edge angles as illustrated. WARNING It is very important for smooth and safe operation to always keep the chain sharp. Your chain need to be sharpened when: •...
  • Page 21: Troubleshoot Guide

    12. Troubleshooting Guide Case 1. Starting failure fuel tank incorrect fuel drain it and use correct fuel fuel filter fuel filter is clogged clean carburetor adjustment screw out of normal range adjust to normal range sparking (no spark) spark plug is fouled/wet clean/dry plug gap is incorrect correct (GAP: 0.65 mm)
  • Page 22: Warranty

    The purchaser is responsible for all related expenses (parts, labour and return costs) if the product is not covered under warranty. Original receipt must be included when returning to: Kiam Power Products Kiam House Birchill Road Knowsley Ind. Park North...

Table of Contents

Save PDF