Superior Fireplaces Signature DRT6340TYN Installation Instructions Manual

Signature series 40 and 45 in. power vent direct-vent gas fireplaces

Advertisement

Quick Links

P/N 506009-16 Rev. NC 12/2013
This manual is one of a set of two supporting this product.
Refer to P/N 506010-12 for Care and Operation Instructions.
Ce manuel est disponible en francais, simplement
en faire la demande. Numéro de la pièce 506009-17.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
INSTALLATEUR : Laissez cette notice avec l'appareil.
CONSOMMATEUR : Conservez cette notice pour
consultation ultérieure.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile
home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating
plate. This appliance is not convertible for use with other gases.
WARNING / AVERTISSEMENT / AVISO
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
WARNING: If the information in these instructions
is not followed exactly, a fire or explosion may
result, causing property damage, personal injury,
or death.
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire
department.
- Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
Signature Series 40 and 45 in. Power Vent
Direct-Vent Gas Fireplaces
Intertek Report No.
MODELS
100513650PRT-001
Decorative Product: Not for use as a heating appliance.
NOTICE: Fireplace is not to be operated by a thermostat.
UNE SURFACE VITRÉE CHAUDE
PEUT CAUSER DES BRÛLURES.
LAISSER REFROIDIR LA SURFACE
VITRÉE AVANT D'Y TOUCHER.
NE PERMETTEZ JAMAIS À UN ENFANT
DE TOUCHER LA SURFACE VITRÉE.
AVERTISSEMENT : Assurez-vous de bien suivre les
instructions données dans cette notice pour réduire au
minimum le risque d'incindie ou d'explosion ou pour
éviter tout dommage matériel, toute blessure ou la mort.
- Ne pas entreposer ni utilizer d'essence ni d'autres vapeurs
ou liquides inflammables dans le voisinage de cet appareil
ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucan interrupteur. Ne pas vous servir des
téléphones se trouvant dans le bâtiment où vous trouvez.
• Appelez immédiatement votre fournisseur de gaz depuis
un voisin. Suivez les instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incindies.
- L'installation et l'entretien doivent être assurés par un
installateur ou un service d'entretien qualifié ou par le
fournisseur de gaz.
INSTALLATION INSTRUC TIONS
DRT6340TYN
DRC6340TYN
CAUSARÁ QUEMADURAS.
TOCAR EL VIDRIO CALIENTE.
LOS NIÑOS DEBEN NUNCA
DRT6345TYN
DRC6345TYN
EL VIDRIO CALIENTE
USTED DEBE NUNCA
TOCAR EL VIDRIO.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Signature DRT6340TYN and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Superior Fireplaces Signature DRT6340TYN

  • Page 1 Signature Series 40 and 45 in. Power Vent Direct-Vent Gas Fireplaces Intertek Report No. MODELS P/N 506009-16 Rev. NC 12/2013 100513650PRT-001 DRT6340TYN DRT6345TYN This manual is one of a set of two supporting this product. DRC6340TYN DRC6345TYN Refer to P/N 506010-12 for Care and Operation Instructions.
  • Page 2: Table Of Contents

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS TABLE OF CONTENTS GENERAL INFORMATION BOX 2 - Power Vent Components: • (1) Power Vent Termination Packaging .........Page 2 WARNING • (1) Termination Adaptor Introduction ........Page 2 •...
  • Page 3 INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS Codes and Standards WARNING WARNING These appliances comply with National Safety Improper installation, adjust- Failure to position the parts in Standards and are tested and listed by Intertek (Report No.
  • Page 4: Massachusetts Requirements

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS Gas Pressure - All Models PURGE CYCLE Burner Orifice Size This is a power vented fireplace that Elevation 0 - 4500 ft (0 - 1370 m) Tables 2 and 3 show the appliance inlet and requires household electrical power manifold gas pressure requirements.
  • Page 5: Cold Climate Insulation

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS COLD CLIMATE INSULATION For cold climate installations, seal all cracks around your appliance with noncombustible NOTE: When the unit is installed material and wherever cold air could enter with one side flush with a wall, the the room.
  • Page 6: Vent Termination Clearances

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS VENT TERMINATION CLEARANCES Combustible Projection 2-1/2" or less in length These instructions should be used as a guide- line and do not supersede local codes in any Combustible Projection way.
  • Page 7 INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS NOTE: Local Codes Or Regulations May Require * See Item D in the Text Below. Different Clearances. Center Line Exterior Wall Inside of Termination Corner Detail NOTE: Location Of The Vent Termination Must Not 24"...
  • Page 8: Minimum Clearances To Combustibles

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS MINIMUM CLEARANCES TO COMBUSTIBLES MANTEL CLEARANCES Inches (mm) Appliance And Vent Clearances 12 (305) MANTEL The appliance is approved with zero clearance to combustible materials 10 (254) MANTEL on all sides.
  • Page 9: Pre-Installation Steps

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS PRE-INSTALLATION STEPS DETAILED INSTALLATION STEPS Step 1. FRAMING The appliance is shipped with all gas controls and components installed and pre-wired. Frame these appliances as illustrated in Figure Before installing the appliance, follow these steps: 8 on Page 10, unless the appliance is to be 1.
  • Page 10: Fireplace And Framing Specifications

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS FIREPLACE AND FRAMING SPECIFICATIONS Framing should be constructed VENT FRAMING of 2x4 or larger lumber. Adaptor Plus 4 ft TOP VENT WITH 2 FEET 10-1/2” Vertical Vent VERTICAL VENT AND (267)
  • Page 11: Step 2. Routing Gas Line

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS Schedule 40 Black Iron Pipe Inside Diameter Length Inside Diameter 0 - 10 ft (0 - 3.1 m) 1/2" (12.7 mm) 10 - 40 ft (3.1 - 12.2 m) 1/2"...
  • Page 12: Step 3. Install The Vent System

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS Power Vent Components Step 3. INSTALL ThE VENT SYSTEM General Information Locate the fireplace as instructed in this manual. Make the following modifications to add the com- ponents used with the Power Vent Kit.
  • Page 13: Vent Section Length Chart

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS VENT SECTION LENGThS i t c i t c O O O O O O O O O O T T T T T T T T T T A A A A A A A A A A Determine the number of straight vent sections...
  • Page 14 INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS A. Frame ceiling opening - Use a plumb line The unitized design of the Secure Vent com- Support the vertical portion of the venting ® ponents will engage and seal both the inner and system every eight feet (2.4 m) above the from the ceiling above the appliance to locate...
  • Page 15 INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS VENT FIGURES NOTES: • Secure Vent components (rigid vent pipe and terminal) are shown. ® • Two 45° elbows may be used in place of one 90° elbow. •...
  • Page 16: Horizontal Termination System

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS hORIZONTAL (OUTSIDE WALL) D. Attach vent components to appliance - To G. Support the vertical run sections - attach a vent component to the appliance TERMINATION SYSTEM Ontheverticalrun,supporttheventingsystem collar, align the dimpled end over the collar,...
  • Page 17 INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS L. Install Firestop/Spacer at exterior wall - Power Vent Install SV4.5HF Firestop/Spacer, provided To help minimize water infiltration Termination with the power vent kit, over the opening at it is recommended that the Firestop/Spacer (SV4.5HF) the exterior side of the framing, long side be installed on the exterior side of the wall.
  • Page 18: Step 4. Field Wiring

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS Step 4. FIELD WIRING • Refer to Figure 25 on Page 19 and install the electrical hardware on the ends of the cable. Male terminals on the Black and White wires, CAUTION: Label all wires prior to disconnection when servic- and ring terminals on the ground wire.
  • Page 19 INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS Wiring - Fireplace (See Figures 27 and 28 on Page 20) • Refer to Figure 26 and install the electrical hardware on the fireplace end of the cable. Male terminals (#10) on the Black and White wires, NOTE: These electronic appliances must be connected to the main and ring terminals (#9) on the ground.
  • Page 20: Step 5. Removing Glass Door Frame Assem- Bly Page

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS ELECTRONIC WIRING DIAGRAM Flame IPI Pilot Sensor (Schematic representation only) Spark Electrode Pilot Tube Optional Split Flow COLOR CODE: 885 Valve B = Black Battery Holder with Switch Battery Holder w/Switch BB = Brown w/Black Stripe ON/Remote/OFF...
  • Page 21: Step 6. Connecting Gas Line

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS Step 6. CONNECTING GAS LINE NOTE: Using a soapy water solution is If bubbles are formed, or gas odor is detected, an effective leak test solution but it is not turn the unit off.
  • Page 22: Step 9. Installing Logs

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS Step 9. INSTALL VOLCANIC STONE, GLOWING EMBERS, AND Firebox Accessories LOGS (TRADITIONAL ONLY), OR GLASS MEDIA (CONTEMPORARY ONLY) Cat. No. Model Description 88L53 Bag of Glowing Embers NOTE: If installing the contemporary burner/floor kit, skip 80L42 FDVS...
  • Page 23 INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS Traditional Only: Log Placement Engage Logs (3 & 4) With The Grate Pins And Align Groves At The Bottom Of The Logs Over The Grate. Figure 37 - Placing Logs 3 and 4 Log Number Description...
  • Page 24: Door Assembly

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS Step 11. BURNER ADJUSTMENTS Step 10. INSTALLATION AND REMOVAL WARNING: Any safety screen or guard re- moved for servicing the appliance must be OF GLASS DOOR Flame Appearance and sooting replaced prior to operating the appliance.
  • Page 25 INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS Burner Air Shutter Adjustment Procedure Air Shutter WARNING Opening • Air shutter adjustment should only be performed by a quali- Main Burner Factory Air Shutter fied professional service tech- Opening Setting - Inches (millimeter) Venturi...
  • Page 26: Finishing Requirements

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS FINIShING REQUIREMENTS Noncombustible materials, such as surrounds and other appliance trim, may be installed on the appliance front face with the exceptions. Wall Details Vertical installation clearances to combustible mantels vary according to Complete the finished interior wall.
  • Page 27: Step 12. Attaching Safety-In-Operation Warnings

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS Step 12. INSTALLER INSTRUCTIONS - ATTAChING SAFETY IN OPERATION WARNINGS It is the installers responsibility to ensure these warnings are properly affixed during installation. These warning labels are a critical step in informing consumers of safe operation of this appliance.
  • Page 28: Installation Accessories

    INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • INSTALLATION INSTRUCTIONS INSTALLATION ACCESSORIES Listed Secure Vent Components Listed Secure Vent / Secure Flex Components ® ® Cat. No. Model No. Description Cat. No. Model No. Description 6"...

Table of Contents