Subscribe to Our Youtube Channel
Related Manuals for Heat & Glo Curve 100S-HS
Summary of Contents for Heat & Glo Curve 100S-HS
- Page 1 CURVE Series Wood Stoves Owner’s Manual Installation and Operation 2/11/2014 Heat & Glo • 7076-108 1...
- Page 2 Curve Series and Welcome to the Heat & Glo Family Hearth & Home Technologies welcomes you to our tradition our stoves, inserts and fireplaces. And yet we are old-fash- of excellence! In choosing a Heat & Glo appliance, you have ioned when it comes to craftsmanship. Each unit is meticu- our assurance of commitment to quality, durability, and per- lously fabricated and surfaces are hand-finished for lasting formance.
-
Page 3: Table Of Contents
Curve Series Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • WARNING! Indicates a hazardous situation which, if not avoided may result in death or serious injury. • CAUTION! Indicates a hazardous situation which, if not avoided, may result in minor or moderate injury. • NOTICE: Indicates practices which may cause damage to the appliance or to property. -
Page 4: Technical Data
Curve Series Technical Data Technical data and dimensions A. Installation The house owner is responsible for ensuring that all neces- Materials: steel plate, cast iron, galvanized sheet, skamol sary national and local safety measures are observed during Max. wood length: 25 cm installation and fitting and also responsible for observing the Weight Curve 100: ca. 98 kg fitting and operating instructions detailed in this manual. Weight Curve 300: ca. 96 kg When you install any kind of fireplace or stove, you must Weight heat-accumulating stones: ca. 86,5 kg... -
Page 5: Installation & Assembly
Curve Series Installation & Assembly A. Positioning Your Wood Burning Stove the back panel so the flue attachment ring can slip through The wood burning stove must be set up so the stove, flue it. Attach the back panel back onto the appliance using connection, flue pipe, and chimney system can be cleaned the same fasteners. Install the venting per the venting and serviced. Consideration should also be made when manufactures specifications. Place the top cover plate locating the appliance in the home due to the supply of (item “C” in Fig. 5.1) from the component pack over the combustion air requirements. -
Page 6: Leveling The Unit
Curve Series D. Leveling the Unit I. Removal of Curve from Pallet Four leveling bolts have come installed on the unit. Follow- 1. Remove the two 11 mm bolts holding the brackets in the ing installation, adjustments can be made to the heights of front and rear of the base on the unit, this requires holding the four bolts from the top of the base pan. -
Page 7: Dimensions & Clearances
Curve Series Dimensions & Clearances Curve 300 rial version www.pdffactory.com pdffactory.com PDF created with pdfFactory Pro trial version www.pdffactory.com 2/11/2014 Heat & Glo • 7076-108 7... - Page 8 Curve Series Curve 100 PDF created with pdfFactory Pro trial version www.pdffactory.com PDF created with pdfFactory Pro trial version www.pdffactory.com PDF created with pdfFactory Pro trial version www.pdffactory.com Heat & Glo • 7076-108 2/11/2014...
-
Page 9: Operation
Curve Series Operation A. General Use D. Fuels The Curve 100 Wood Stove is designed and tested for The Curve 100 wood stove is designed to burn a wide intermittent use. This means that it is not designed for or range of firewood species. In general hardwoods are better recommended to burn continuously for 24 hours. - Page 10 Curve Series Figure 01 Proper Fill and Startup Configuration Lower intake holes Add paper to back of firepot making sure to not block lower air inlet with paper Add small pieces of wood on top of paper allowing for air flow between pieces Secondary Holes Add larger log on top of pile making sure it does not go above the upper intake holes Fig.
-
Page 11: Primary Air
Curve Series E. Primary Air G. Secondary Air (Lower Air Control) (Fig. 11.1) This unit is equipped with a secondary combustion system The primary air is controlled by the lever on the left side of that cannot be regulated. The purpose of this secondary the appliance. -
Page 12: Side Door Handle Operation
Curve Series I. Side Door Handle Operation this material is a high quality material specifically designed for wood burning appliances, it is subject to normal wear (Fig. 12.1) and tear and should be replaced if burn times are reduced To open the front door, pull the lever located on the blower or there is concern of leakage. -
Page 13: Chimney Systems
Curve Series Chimney Systems A. Chimney Systems B. Drafting A chimney or flue system is required to run your wood stove Weather and chimney location can affect the draft of your safely and efficiently. When a fire is started in the fire box stove resulting in different performance settings. For windy conditions, the draft may be higher which will result in hot gases are released and exit the firebox into the chimney changing the air control settings for the same performance. system. -
Page 14: Maintenance
Curve Series Maintenance A. Ash Drawer B. Refractory The firebox is lined with molded refractory firebrick. The (Figure 14.1) refractory protects the outside of the appliance and retains Before attempting any maintenance on the unit ensure the heat necessary for a clean efficient burn. The material that the unit is cold and has no embers in the firebox. To is a porous ceramic material that can break from abuse. access the ash drawer open the glass front. -
Page 15: Troubleshooting
Curve Series Troubleshooting Smoke escaping • Inferior firewood (waste wood, pallets etc.) • Damp wood • Chimney not drawing sufficiently • Chimney not drawing properly • Vacuum in room • Chimney is not properly dimensioned for the stove Excessive soot build-up in chimney • Check if the smoke gas pipe/chimney are blocked • Poor burning (more air required) • Is the chimney the right height for its surroundings? • Damp wood • At rear outlet, check that the flue pipe does not obstruct the chimney draught The surface of the stove is turning grey • Overheating (see instructions for heating) • Vacuum in room • The door is opened before the embers have Poor heating performance of stove •... -
Page 16: Warranty
Curve Series Warranty Hearth & Home Technologies Inc. (“HHT”) extends the following warranty for Heat & Glo Curve Series wood stoves WARRANTY COVERAGE AND PERIOD: HHT warrants that your Heat & Glo Curve Series wood stove will be free from defects in materials and work- manship at the time of manufacture. -
Page 17: Service Parts List
Curve Series Service Parts List CURVE-100G-HS Service Parts Beginning Manufacturing Date: June 2013 Wood Stove Ending Manufacturing Date: Active IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor. ITEM DESCRIPTION COMMENTS... - Page 18 Curve Series CURVE-100S-HS Service Parts Beginning Manufacturing Date: June 2013 Wood Stove Ending Manufacturing Date: Active IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor. ITEM DESCRIPTION COMMENTS...
- Page 19 Curve Series CURVE-300G-HS Service Parts Beginning Manufacturing Date: June 2013 Wood Stove Ending Manufacturing Date: Active IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor. ITEM DESCRIPTION COMMENTS...
- Page 20 Curve Series CURVE-300S-HS Service Parts Beginning Manufacturing Date: June 2013 Wood Stove Ending Manufacturing Date: Active IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor. ITEM DESCRIPTION COMMENTS...
-
Page 21: Homeowner Notes
Curve Series Homeowner Notes 2/11/2014 Heat & Glo • 7076-108 21... - Page 22 Curve Series Heat & Glo • 7076-108 2/11/2014...
- Page 23 Curve Series 2/11/2014 Heat & Glo • 7076-108 23...
- Page 24 CONTACT INFORMATION: Hearth & Home Technologies 1445 North Highway Colville, WA 99114 Division of HNI INDUSTRIES We recommend that you record the following pertinent information for your heating appliance Date purchased/installed: Serial Number: Location on appliance: Dealership purchased from: Dealer phone: Notes: This product may be covered by one or more of the following patents: (United States) 5341794, 5263471, 6688302, 7216645, 7047962 or other U.S.
Need help?
Do you have a question about the Curve 100S-HS and is the answer not in the manual?
Questions and answers