Related Manuals for Terratek TPMT15VBE
Summary of Contents for Terratek TPMT15VBE
- Page 1 Multi purpose oscillating tool TPMT15VBE User Manual – Please read and retain for future reference.
- Page 2 Contents Parts List Technical Information Safety Instructions Using your tool Maintenance Warranty Accessories A Rubber backing pad B Plunge Cutter C Cutter D Bolt E Washers F Sanding sheets (8) G Segment saw blade ...
- Page 3 Fig.1 A On/Off switch B Variable Speed Control C Accessory Holder ...
-
Page 4: Parts List
Parts List 1 Screw M8x12 24 Pull brace 2 Outside flange 25 Link pole 3 Spindle 26 Plastic housing 4 Rubber casing 27 Brush holder 5 Circlip for shaft 26 28 Carbon brush 6 Spline spring washer 29 Tubular rivet 7 Bearing 6000 30 Switch 8 Toggle block 31 Cord clip 9 Bronze bushing 32 Screw ST4.0x14 10 Screw ST4x27 33 Back housing (right) ... -
Page 5: Exploded Assembly Diagram
Exploded Assembly Diagram NOTICE: Actual product may vary from pictures shown. -
Page 6: Technical Information
Technical Information Voltage: 230-240V ~ 50Hz Power: 220W Speed: 15000-22000 opm Oscillating angle: 3° Weight: 1.99/2.67kgs Read this entire manual before using this product. Failure to do so can result in serious injury. Save this manual for future reference. Copyright© 2012 by ACL Group (intl) Ltd. All rights reserved. This manual or any artwork contained herein must not be reproduced in any shape or form without the express written consent of ACL Group (Intl) Ltd. -
Page 7: Important Safety Information
Read and Keep This Manual Please read carefully all instructions within this manual. Failure to follow all safety warnings can result in serious personal injury. The term “Power Tool” in all of the following warnings refers to your mains operated (corded) or battery operated (cordless) power tool Important SAFETY Information This symbol is to warn you of potential personal injury hazards. -
Page 8: Personal Safety
Before use, ensure that the power outlet you are using matches the plug on your power tool and that the voltage of the outlet matches that of your power tool. Only use grounded extension cords with power tools fitted with 3 pin plugs and if using outdoors ensure any extension cord is suitable for outdoor use. -
Page 9: General Safety Instructions
C) Do not operate tool without guards in place. D) Do not perform any operation freehand. E) Never reach around cutting tools. F) Turn off tool and wait for cutting tools to stop before moving workpiece or changing settings. G) Disconnect power (or unplug tool) before changing cutting tools or servicing. GENERAL SAFETY INSTRUCTIONS Read this owner's manual completely and make sure you understand all of its safety guidelines. -
Page 10: Additional Safety Rules For Oscillating Tools
26. NEVER LEAVE TOOL RUNNING UNATTENDED. Turn power off. Don’t leave tool until it comes to a complete stop. 27. Double Insulation eliminates the need for the three wire grounded power cord and grounded power supply system. This power tool is supplied with all the relevant safety guards and features, it should be checked before every operation, this manual should be read and kept in a safe place. -
Page 11: Package Contents
and balance at all times. This enables better control of the power tool in unexpected situations. Keep hands away from cutting area. Do not reach under the material being cut. The proximity of the blade to your hand is hidden from your sight. Do not use dull or damaged blades. -
Page 12: On-Off Switch
WARNING: Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. Assembly 1. Turn the Power Switch off and unplug the tool. 2. Place the attachment over the Spindle, shoulder facing away from the tool. Line up the holes on the attachment with the pins on the Spindle shoulder. -
Page 13: General Maintenance
Accessories CAUTION: Use only accessories or attachments recommended for use with your Terratek tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. -
Page 14: Declaration Of Conformity
Declaration of Conformity We ACL Group (Intl.) Ltd, England DN6 8LZ declare that the Terratek Oscillating Power Tool has been manufactured according to our full quality assurance procedures. The declaration is to certify that it conforms to CE, EMC, MD and RoHS directives:... - Page 15 ACL Group (Intl) Ltd Doncaster, England Email: info@terratekintl.com www.terratekintl.com...