Table of Contents
Advertisement
Quick Links
Introduction .................................................... 1
Glossary .......................................................... 3
Configurations ................................................. 4
Description of Setup Keys ................................. 5
Zone Control .................................................... 6
Zone Setup ..................................................... 6
Zone Operation ................................................ 7
Scene Control .................................................. 8
Scene Setup .................................................... 9
Scene Operation .............................................. 11
Scene Controller Conf command ........................ 11
Additional Device Setup .................................. 12
Add/Delete Devices .......................................... 12
Assign Association for Two Devices ..................... 13
Definition of Association groups ......................... 15
Change Device Configuration ................................ 15
Add A Simple AV Device .................................... 16
Advanced Z-Wave Network Setups .................. 17
Secondary Controller ........................................ 17
Controller ........................................................ 18
to A New Primary Controller (Primary shift) ......... 19
Primary Controller (Primary shift) ....................... 20
Listening Mode ................................................. 22
Resetting Your Network..................................... 23
AUDIO/VIDEO SETUP AND OPERATION .......... 24
Description of Audio/Video Control Keys .............. 25
the Library ...................................................... 28
Table of Contents
Advertisement
Table of Contents
Related Manuals for Z-Wave HSK-100Z
Summary of Contents for Z-Wave HSK-100Z
-
Page 1: Table Of Contents
A New Primary Controller (Primary shift) ..19 Transferring Only Network Information to A New Primary Controller (Primary shift) ....... 20 Replicating All Network and Device Information from A Primary Controller to your HSK-100Z (aka “Learning Mode”) ........21 Listening Mode ..........22 Resetting Your Network........23 AUDIO/VIDEO SETUP AND OPERATION .. - Page 2 Learning IR Commands ........30 Operating the HSK-100Z for AV Equipment ..31 ADVANCED OPERATION FOR AV EQUIPMENT .. 33 Secondary Function .......... 33 IR Boost Mode ..........33 Restore Factory Settings ........33 MAINTENANCE ..........34 FREQUENTLY ASKED QUESTIONS ....34 Z-Wave Frequently Asked Questions ....
-
Page 3: Introduction
HSK-100Z Z-Wave AV Scenario Controller Introduction The HSK-100Z Z-Wave AV Scenario Controller is a universal AV remote and also a Z-Wave controller (Figure 1). As a universal remote, the HSK-100Z replaces all your AV remotes through its built-in IR code database or IR code learning. - Page 4 Before using the HSK-100Z, please install the batteries: 3xAAA batteries are required for operation. Remove the battery cover on the back of your HSK-100Z. Check the polarity of the batteries and the "+/-" marks inside the battery compartment.
-
Page 5: Glossary
Z-Wave network. A collection of Z-Wave devices controlled by primary and secondary controllers operating Z-Wave on the same system. A Z-Wave network has Network its own unique ID code so that controllers not in the network cannot control the system. -
Page 6: Configurations
Configurations Please open the configuration compartment then you can see the HSK-100Z setup keys (Figure 2). Status LED A Status LED B Figure 2 Setup Keys of the HSK-100Z... -
Page 7: Description Of Setup Keys
The ADD and REMOVE keys are used during basic Zone Setup process. ADD key will perform two functions: Add a target device to Z-Wave network, also known as INCLUSION; Add the device to the assigned GROUP. REMOVE key will only remove the target device from its assigned group but will not exclude it from the network. -
Page 8: Zone Control
For example, you can group all your bedroom lights together so that all of them will turn on with the press of a button. You can control up to 8 zones with your HSK-100Z. Each zone supports up to 232 Z-Wave devices. Zone Setup... -
Page 9: Zone Operation
Note: If the ERROR LED turns on or blinks, meaning the setup process is failed. Please redo the process. Zone Operation After adding devices to your HSK-100Z using Zone Setup, you can turn the device on/off or up/down via the corresponding zone control keys in front (Figure3). -
Page 10: Scene Control
Figure 3 Zone Control Keys of the HSK-100Z Scene Control A Z-Wave Scene is a series of controlled events that work in unison for a planned task or home ambience. For example, you can setup a scene for “Watch DVD” where the scene button on the HSK-100Z could dim the lights and turn on your TV, DVD Player, and AV Receiver. -
Page 11: Scene Setup
Scene Setup Adding Device to A Scene Step Setup Key Setup LED Behavior The OK light turns on Press OK LED blinks once and Press stays on LED A blinks slowly OK LED blinks once and Select a scene number from 1 to 16 (1-8 or stays on SHIFT 1-8) - Page 12 Removing Device from A Scene Step Setup Key Setup LED Behavior The OK light turns on Press OK LED blinks once and Press stays on LED A blinks slowly OK LED blinks once and Select a scene number from 1 to 16 (1-8 or stays on SHIFT 1-8)
-
Page 13: Scene Operation
HSK-100 keypad. If we use this command to create a scene, the existing scenes created by the HSK- 100Z will be deleted automatically. In addition, if we use HSK-100Z to assign a device to a scene button, the setting created by the... -
Page 14: Additional Device Setup
Please remove the scene setting by using one of Clear scene in the HSK-100Z. Use ASSOCIATION_SET to add a device. In this case, all scenes created by the HSK-100Z will be cleared automatically. Additional Device Setups Add/Delete Devices Adding Device to the Network Step... -
Page 15: Assign Association For Two Devices
Assign Association for Two Devices The HSK-100Z can be used to assign one device to automatically interact directly with another device. For example you can assign a door sensor (primary node) to turn on the light switch (secondary node) when the door is opened. - Page 16 Removing Device from Association Step Setup Key Setup LED Behavior The OK light turns on Press OK LED blinks once and Press stays on LED A blinks slowly OK LED blinks once and Select a group number from 1 to 16 (1-8 or stays on SHIFT 1-8) ...
-
Page 17: Definition Of Association Groups
Zone Control #1-#8 9-24 Scene Control #1-#16 Change Device Configuration This function is used to modify the parameter of the Z-Wave device via the configuration command class. This is possible only when the HSK-100Z is primary controller or inclusion controller. Step... -
Page 18: Add A Simple Av Device
AV device mode key. Channel Mode Key SAT/CBL Shift+TV Shift+DVD Shift+SAT/CBL Shift+AUX To add a Z-Wave Simple AV device to HSK-100Z, please follow these steps: Step Setup Key Setup LED Behavior OK LED on Press in Zone ... -
Page 19: Advanced Z-Wave Network Setups
Advanced Z-Wave Network Setups Copying All Network and Device Information to A Secondary Controller You can add a secondary controller to your network and copy all of your HSK-100’s network and device information to the secondary controller by following the steps below. -
Page 20: Copying Network Information To A Secondary Controller
Copying Network Information to A Secondary Controller You can add a secondary controller to your network and copy all of your primary controller’s network information to the secondary controller by following the steps below. Step Setup Key Setup LED Behavior Press &... -
Page 21: Transferring All Network And Device Information To A New Primary Controller (Primary Shift)
Transferring All Network and Device Information to A New Primary Controller (Primary Shift) You can transfer all of your controller information to another remote so that it will become the new primary remote. This is done by following the steps below. Step Setup Key Setup LED Behavior... -
Page 22: Transferring Only Network Information To A New Primary Controller (Primary Shift)
Transferring Only Network Information to A New Primary Controller (Primary Shift) You can just transfer network information to another remote so that it will become the new primary remote. This is done by following the steps below. Step Setup Key Setup LED Behavior Press &... -
Page 23: Replicating All Network And Device Information From A Primary Controller To Your Hsk-100Z (Aka "Learning Mode")
Mode”) Your HSK-100Z can: Copy the settings from another Z-Wave controller Be included into existing Z-Wave network and become a new primary or secondary remote Be excluded from the Z-Wave network by following the steps below. Step... -
Page 24: Listening Mode
Listening Mode There are multiple usages by entering this mode: Version command class: To get application software version, the Z-Wave protocol version and the supported Z-Wave command version of this controller. Manufacturer command class: To get the manufacture ID, product type ID and the product ID of this controller. -
Page 25: Resetting Your Network
Resetting Your Network You can reset your HSK-100Z to clear all Z-Wave network and device information by the following steps: Step Setup Key Setup LED Behavior Press & hold OK LED on for 3 seconds Place the two controller close to each other ... -
Page 26: Audio/Video Setup And Operation
AUDIO/VIDEO SETUP AND OPERATION In addition to Z-Wave device and scene control, your HSK-100Z is also a universal remote which enables you to control all your audio/video systems around your house. Audio/Video Control Keys Figure 5 Audio/Video Control Keys of the HSK-100Z Note: The audio/video control of the HSK-100Z can be done via infrared or Z-Wave. -
Page 27: Description Of Audio/Video Control Keys
Description of Audio/Video Control Keys The HSK-100Z operates up to 8 AV equipments which are accessed by using the SHIFT key and TV or DVD and so on. Note: The SHIFT key is used when operating both the AV and Z-Wave... - Page 28 4-way directional pad for navigating on- screen menu and OK button for selecting menu options Menu, also list when in shift mode Exit, also Live for SAT/CBL mode when in shift mode Previous track Next track Stop Record Rewind Play Pause Fast forward Numeric number 1;...
-
Page 29: Av Equipment Selection By Entering Device Code
2. Press the desired Device Mode Key (e.g. TV). 3. Hold down "CH +" and "VOL -" on the HSK-100Z simultaneously for 3 seconds until the green indicator lights up. 4. Use the number keys "0" - "9" to enter your 4-digit Device Code. -
Page 30: Av Equipment Selection By Searching Through The Library
1. Turn on your device manually (e.g. TV). 2. Press a desired Device Mode Key (e.g. TV). 3. Hold down "CH +" and "VOL -" on the HSK-100Z simultaneously for 3 seconds until the indicator lights up. 4. Enter a corresponding Magic Search Code from the following table. - Page 31 If the red indicator flashes six times after your pressing of key, you are already at the last code of the library. Press "CH +" and "VOL -" to resume the HSK-100Z and repeat the above procedures carefully to search again.
-
Page 32: Learning Ir Commands
3 seconds until the green indicator lights up. Enter the learning code "0", "0", "0", "0". The green indicator light will flash once then stay lit. The HSK-100Z is now ready to learn. Place the HSK-100Z and your device remote on a flat surface, aimed at each other 1-3 inches apart. -
Page 33: Operating The Hsk-100Z For Av Equipment
Operating the HSK-100Z for AV Equipment Normal Operation Once you have setup the HSK-100Z for your AV equipment, it works like your original remote control. To operate, just aim it at your equipment, press an appropriate device mode key and invoke the desired function by pressing a corresponding key on the HSK-100Z. - Page 34 Punch through volume allows you to operate volume up and down without having to switch the device modes repeatedly even when your HSK-100Z is in other operating modes. To activate the punch through volume setting: 1. Press desired Device Mode Key (e.g. TV).
-
Page 35: Advanced Operation For Av Equipment
4. Release (the green indicator flashes twice if the setting is deactivated). ADVANCED OPERATION FOR AV EQUIPMENT Secondary Function Some keys are able to access 2 functions through the use of the shift key. To use a buttons secondary function, press the shift key then the next button pressed will perform its secondary function after which the buttons will return to their primary functions. -
Page 36: Maintenance
What can the HSK-100Z do for me? The HSK-100Z can control a combination of up to 232 different Z- Wave devices in 8 zones or 16 scenes around your house while also being a standard universal remote that can control up to 8 AV equipments. -
Page 37: Av Control Frequently Asked Questions
Why do I need a different module for outdoor lighting? The outdoor module is designed to withstand various weather conditions including heat, rain and snow. Can I use 2 or more HSK-100Z controllers in my house at one time? You can use multiple HSK-100Z around your house by assigning one remote to be the primary remote and have an additional secondary controller. -
Page 38: Technical Specifications
100ft indoor line of sight, in Max. Range unobstructed environment Power AAA x 3pcs operation: 0~40℃ Temperature storage: -20~60℃ Humidity 10~85%, non-condensing Dimension (LxWxH) 240mm x 60mm x 29mm Weight (ex. Batteries) 150g Certifications CE, FCC, RoHS, Z-Wave... -
Page 39: Warranty
WARRANTY Limited One (1) Year Warranty This warranty does not cover or apply to: (a) damage to the product due to misuse, mishandling, and abuse, (b) products not used in accordance with manufacturer's instructions or recommendations, (c) product not assembled or installed according to manufacturer's instructions, (d) normal wear and tear, (e) wearing of the cover do to improper installation of cover and goods (f) damage to the contents of the shelter, (g) permits required due to zoning issues,... - Page 40 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
-
Page 41: Warnings
Operation of the Z-Wave device may be in a different room then the controlled appliances, also an unintentional activation may occur if the wrong button on the remote is pressed. Z-Wave devices may automatically be powered on due to timed event programming.
Need help?
Do you have a question about the HSK-100Z and is the answer not in the manual?
Questions and answers