Related Manuals for Recordex Motorized Electric Projection Screen
Summary of Contents for Recordex Motorized Electric Projection Screen
- Page 1 Motorized Electric Projection Screen Thank You For Choosing Our Projector Screen. Please Read This Manual Carefully Before Using Your New Screen.
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS When using your photographic equipment, basic safety precautions should always be followed, including the following: Ÿ Read and understand all instructions before using. Ÿ Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use. Ÿ... -
Page 3: Important! Please Read First
IMPORTANT! PLEASE READ FIRST. Thank you for selecting our professional motorized electric projector screen. We know you are ready to get started using your screen, but we ask that you please take a few minutes to read through this manual to ensure proper installation and use of your new screen. -
Page 4: Installation
INSTALLATION • Unpack the screen carefully and verify that the screen was not dam- aged during shipment. (If the screen was damaged during shipping please initiate a damage claim with the freight carrier immediately.) • Check the contents of the box against Figure 1.0 to be sure that nothing is missing. -
Page 5: Screen Operation
SCREEN OPERATION Plug In The Screen • Plug the screen power cord to a grounded 110V/60Hz power outlet. We recommend plugging your screen into a protected power source. Using a surge pro- tector, line conditioner, or UPS will help project your investment from power surges. 3-Way Switch Operation (fig. -
Page 6: Read First
READ FIRST NOTE: The remote is fully function right out of the box. You DO NOT need to program the remote before using your new projector screen. The following instructions for programming the remote are optional and are used to turn on or off ad- vanced features that many users will not find necessary. -
Page 7: Remote Control Troubleshooting
Matching Additional Remotes to the Receiver • Enter setup status (see above) • Press the UP button of the Wall Switch or a working Remote Control to place the Remote Receiver into matching mode. You will here two beeps (du-du) to let you know you are in matching mode. •... - Page 8 SPECIFICATIONS & DIAGRAMS Screen Surface Screen Fabric Matte White Gain: 0.9 Viewing Angle: >160° High Color Rendering, High Resolution Gain & Viewing Angle Measurement PAGE NO. 8...
- Page 9 SPECIFICATIONS & DIAGRAMS Spare Parts List for Motorized Electric Screen 0001 LEFT END CAP 0101 ROLLER ROTOR 0002 SCREEN HOUSING 0102 SPRING 0003 RIGHT END CAP 0103 OSCILLATING LEVER 0004 BEARING MOUNTING 0104 SHAFT 0005 BEARING 0105 IDLER WHEEL 0006 ROLLER END CAP 0106 IDLER WHEEL SHAFT...
- Page 10 SPECIFICATIONS & DIAGRAMS 00- 0 1 00- 0 2 00- 0 3 00- 0 4 00- 0 5 00- 0 6 00- 0 7 00- 0 8 00- 1 0 00- 0 9 00- 1 1 00- 1 4 00- 1 5 00- 1 3 00- 1 2 AC 110V/60Hz...
-
Page 11: Operating Tips
SPECIFICATIONS & DIAGRAMS Technical Data for Remote Control & IR Receiver Unit • Input: 110VAC±10% (60Hz) • Output current to motor: ≤1A • Code error rate: ≤1/1000000 • Remote control distance: ≤ 20m (65.6 ft) • Maximum number of remotes per IR receiver: 5 remotes • Control signal: IR 38Khz • Minimum and Maximum effective button press time: >0.3 sec to ±120 sec TROUBLESHOOTING &...
Need help?
Do you have a question about the Motorized Electric Projection Screen and is the answer not in the manual?
Questions and answers