JVC TIMELAPSE SR-S990E Instructions For Use Manual page 13

4 ON-SCREEN/MENU SWITCHES
4-7 Contents of Menu Switches
[ ]: Factory setting • The lower section in the items and set values columns shows what's on the VCR's display.
Screens Items Set values
CNT MEM SW [OFF]
VTR MODE Sets whether or not the counter memory function is activated.
ON OFF: The counter memory function is not activated.
ON: The counter memory function is activated.
OFF
VTR 1
ON
* The counter memory function is not available during repeat recording/
playback, auto REW, alarm search, alarm scan and date/time search.
POWER ON [OFF] Enables or disables automatic external timer recording or automatic
REC ON restart of recording after a power failure.
OFF: External timer recording or automatic recording after power
OFF
VTR 2
ON
ON: Recording starts automatically when power is turned on.
AUTO REC [OFF] Sets whether or not Recording Check is automatically performed at the
CHECK ON beginning of a tape in the Repeat Recording mode.
OFF: Automatic recording check function is disabled.
OFF
VTR 3
ON: Automatic recording check function is enabled.
ON
AUTO REW [OFF] Sets whether or not the tape is rewound automatically when the tape
ON ends.
OFF: The tape stops at the end.
OFF
VTR 4
ON: The tape automatically rewinds and enters the Stop mode (auto
ON
* When the repeat recording/playback function is set to "ON", the
repeat function has priority.
* If the menu switch <TAPE END MODE> on the <ALARM/SENSOR
MODE> screen is set to "STOP", the Stop mode is engaged when
the tape ends even when there is an alarm or sensor recording. The
tape does not rewind.
REPEAT PLAY [OFF] Enables or disables the repeat playback function.
ON OFF: The repeat playback function is disabled.
ON: When the tape ends, it is automatically rewound and played back
OFF
VTR 5
ON
Enables or disables the repeat recording function.
REPEAT REC [OFF]
OFF: The repeat recording function is disabled.
ON
ON: When the tape ends, it is automatically rewound and recording
OFF
VTR 6
ON
* If the menu switch <TAPE END MODE> on the <ALARM/SENSOR
MODE> screen is set to "STOP", the Stop mode is engaged when
the tape ends even when there is an alarm or sensor recording. The
repeat recording is not executed.
* When this menu switch is set to "ON", externally activated recording
is not executed.
24
Function
When the tape reel counter value reaches 0000 in the FF/REW
mode, the VCR enters the Stop mode automatically.
failure is disabled regardless of whether power is supplied or not.
REW).
again from the beginning.
starts again from the beginning. When set to "ON", the [REPEAT]
indication on the VCR's display lights.
4 ON-SCREEN/MENU SWITCHES
4-7 Contents of Menu Switches
[ ]: Factory setting • The lower section in the items and set values columns shows what's on the VCR's display.
Screens Items Set values
Selects series recording or automatic recording with an external VCR
SRI/EXT SRI/EXT REC [OFF]
activation signal.
MODE SERIES
OFF:
EXT
(VCR's display) OFF
SERIES: The series recording function is enabled.
SR ET 1 SERI
EXT:
EIT
* When the menu switch <REPEAT REC> is set to "ON", externally
activated recording is not executed.
Selects the mode engaged when externally activated automatic
EXT REC END [NORMAL]
recording ends.
OPE OFF
NORMAL: The Stop mode is engaged.
SR ET 2
NORn
OPE OFF: The Stop mode is engaged and the operating power mode
POFF
CNT TAPE END [OFF] Outputs a tape end signal from the rear panel's [TAPE END OUT] terminal
500 when the tape reaches the set tape reel counter value during recording.
1000 During series recording, a series recording signal is output to a connected
. .
VCR for continuous recording.
.
OFF: The counter end output function is disabled.
9500
500 : A tape end signal is output when the set tape reel counter value is
OFF
SR ET 3
. .
.
500
9500
. .
.
9500
ALARM/ REC MODE [OFF] Selects the alarm recording or sensor recording function.
SENSOR ALARM • Alarm recording: When an alarm signal is input to the rear panel's
MODE SENSOR [ALARM IN] terminal during recording, the mode switches to the 3H (SP)
ALL recording mode for realtime recording of the alarm event.
• Sensor recording: When an alarm signal is input to the rear panel's
OFF
AL SE 1
[ALARM IN] terminal in the Stop mode (Stop mode, Timer Recording
ALAR
Standby or Operating Off mode), recording starts in the 3H (SP) mode.
SENS
ALL OFF:
ALARM:
SENSOR: Sensor recording is executed.
ALL:
DURATION 5 SEC Selects the recording duration for alarm or sensor recording.
10 SEC 5 — 180 SEC: Alarm or sensor recording is performed for the specified
15 SEC
30 SEC TAPE END: Alarm or sensor recording continues to the end of the tape.
60 SEC MANUAL:
120 SEC
[180 SEC]
TAPE END
MANUAL
AL SE 2
5
. .
.
180
TPEN
nANU
Function
The series recording and automatic recording with an external
signal functions are disabled.
The automatic recording function with an external signal is enabled.
is turned off.
reached during recording. A buzzer sounds when the menu switch
<END BUZ> on the <BUZZER/IN OUT> is set to "ON".
For more information on the relationship between the tape reel
counter value and the tape remaining time, refer to page 64.
Alarm or sensor recording is not executed.
Alarm recording is executed.
Both alarm and sensor recording are executed.
time (5 sec. to 180 sec.)
Alarm or sensor recording continues for as long as alarm
signals are input. Set to this position when specifying the
alarm recording time with a switcher.
*To ensure accurate alarm search and alarm scan operation,
be sure to set the recording time to 5 seconds or more.
25