Sony FD Triniton KV-29FQ75A Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. TV
  5. KV-29FQ75A
  6. Service manual

Sony FD Triniton KV-29FQ75A Service Manual

Color tv
Hide thumbs Also See for FD Triniton KV-29FQ75A:
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL

MODEL
COMMANDER
KV-29FQ75A
KV-29FQ75D
DEST
CHASSIS NO.
RM-893
ET
SCC-Q45A-A
RM-893
AEP
SCC-Q41D-A
MODEL
KV-29FQ75E
KV-29FQ75K
1
AE-5A
CHASSIS
COMMANDER
DEST
CHASSIS NO.
RM-893
ESP
SCC-Q43A-A
RM-893
OIRT
SCC-Q42B-A

Advertisement

Table of Contents
loading

Related Manuals for Sony FD Triniton KV-29FQ75A

Summary of Contents for Sony FD Triniton KV-29FQ75A

  • Page 1: Service Manual

    SERVICE MANUAL AE-5A CHASSIS MODEL MODEL COMMANDER DEST CHASSIS NO. COMMANDER DEST CHASSIS NO. KV-29FQ75A KV-29FQ75E RM-893 SCC-Q45A-A RM-893 SCC-Q43A-A KV-29FQ75D KV-29FQ75K RM-893 SCC-Q41D-A RM-893 OIRT SCC-Q42B-A...

  • Page 2: Table Of Contents

    TANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, THESE COMPONENTS WITH SONY PARTS WHOSE PART NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT LE NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT MANUEL SUPPLEMENTS PUBLISHED BY SONY.
  • Page 3 a i l i r T t i n ) y l l f e o i t . s l . s l . s l . s l . s l e i l t i n i g i l a t e t l o i t...

  • Page 4: Rear Connection Panel

    21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio output B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left) Output impedence : Less than 1kohm*...
  • Page 5 AE-5A SELF DIAGNOSTIC SOFTWARE The identification of errors within the AE-5A chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
  • Page 6 Error Detection Monitor Device acknowledge is used to check IIC errors. Device acknowledge is checked by sending an IIC start sequence during CRT power on. Each device is checked three times, if there is no acknowledge after each attempt, it will be regarded as an error. There are three steps to check for errors.
  • Page 7 2. Error Reader Display The error reader display is connected to the service connector to read actual error codes. The part number for the error reader display is S-188-900-10. Once an error has been detected it will then be displayed on the two digit error reader. The errors displayed refer to the following table.

  • Page 8: General

    SECTION 1 GENERAL...

  • Page 15: Disassembly

    SECTION 2 DISASSEMBLY 2-1. Rear Cover Removal 2-2. Speaker Connector Disconnection Remove the rear cover fixing screws indicated. Take care Before completely removing the rear cover disconnect the when removing the rear cover not to damage the speaker speaker connector which is located on the inside. cables [Disconnect the speaker connector] as speakers are fitted inside the rear cover.

  • Page 16: Service Position

    2-4. Service Position 2-5. D1 Board Removal To remove the D1 Board release the clip circled and gently Position the PWB as indicated to access the solder side. To gain access to the D Board follow the instructions on page remove the board in a vertical direction.

  • Page 17: Front Control Removal

    2-8. Front Control Module Removal 2-9. F3 and H6 Board Removal To remove the F3 and H6 Boards release the clips circled and Remove the two screws fixing the user control module to the ease the boards gently away from the main support bracket. front underside of the set.

  • Page 18: Picture Tube Removal

    2-12. Picture Tube Removal WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap.

  • Page 20: Set-Up Adjustments

    SECTION 3 SET-UP ADJUSTMENTS Carry out the adjustments in the following order : • When complete readjustment is necessary or a new picture tube is 3-1. Beam Landing. installed, carry out the following adjustments. 3-2. Convergence. • Unless there are specific instructions to the contrary, carry out 3-3.

  • Page 21: Convergence

    Fig.3-4 Purity control magnets Align both Purity magnets Purity magnets to the vertical position Align pips on each magnet 3-2. Convergence (1) Screen centre convergence [Static convergence] Input a dot pattern signal from the pattern generator. Normalize the picture setting. [Moving vertically], adjust the V.STAT magnet so that the vertical red, green and blue dots coincide at the centre of the screen.
  • Page 22 Correction for HMC [Horizontal mis-convergence] and VMC HTIL correction can be performed by adding a THL correction [Vertical mis-convergence] by using the BMC [Hexapole] magnet. assembly to the Deflection yoke. a). HMC correction by BMC [Hexapole] magnet and movement of the electron beam.

  • Page 23: Focus Adjustment

    Layout of each control 3-3. Focus Adjustment Receive a television broadcast signal. Normalize the picture setting. Purity magnet Adjust the focus control located on the flyback transformer to BMC (Hexaploe) magnet obtain the best focus at the centre of the screen. V STAT convergence magnet Bring only the centre area of the screen into focus, the magenta- Y-splitting axis correction magnet...

  • Page 24: Circuit Adjustments

    SECTION 4 CIRCUIT ADJUSTMENTS 4-1. Electrical Adjustments Service adjustments to this model can be performed using the supplied Remote Commander RM-893. How to enter into the Service Mode Turn on the main power switch of the set while pressing P + (plus) and P - (minus) buttons on the front drop down control panel. L/G/S/I R/D/D/D MONO...
  • Page 25 Initialising Menu Basic Setting s i l Model Setting The menu contains a list with all the available models of this software to set up the TV set in an easy way. The selection of a model is setting data for its features and hardware resources which cannot be detected by the automatic power on H/W detection as well as a special model byte to get an unique model identification for models which cannot be differed by...
  • Page 26 c t i Table.4-5 l a i t i s c i l Table.4-7 t l i Table.4-6 t l i Table.4-8...
  • Page 27 - r r p i l l r I Table.4-9 . r r . r r Table.4-11 y t i l r t Table.4-12 l r t Table.4-10...

  • Page 28: Volume Electrical Adjustments

    V SIZE V LIN t i s AFC V BOW V POS H POS t i s H SIZE H PIN CUSH H TILT l l o n i l n i l H UP COR Table.4-13 AFC V ANGLE Deflection System Adjustment Enter into the service mode and select ‘Deflection’...

  • Page 29: Test Mode

    4-3. TEST MODE 2: Is available by pressing the ‘TEST’ button twice, OSD ‘TT’ appears. The functions described below are available by selecting the two numbers. To release the ‘Test mode 2’, press 0, 10, 20 ... twice or switch the TV set into Stand-by mode. Pressing the two Local Control buttons (+ and -) during power ON will also switch into ‘TT’...
  • Page 30 Memo...
  • Page 31 5-1. BLOCK DIAGRAMS (1) CN2301 (1/2) IC2301 VP TEXT IN VP IN B RED TEXT IN R IN B CN2301 HP TEXT IN (2/2) HP IN B GREEN TEXT IN Y SUB OUT G IN B Y OUT PORT 2 USUB OUT U OUT POWER SUPPLY AND DEFLECTION...
  • Page 32 5-1. BLOCK DIAGRAMS (2) TU1326 TU1350 (SUB-TUNER) CN1601 AGC MONITOR MONITOR STANDBY AC ON/OFF BUFFER QSS1 Q1328, TO D BOARD Q1329 OVER VOLTAGE CN6101 IC1400 QSS2 BUFFER I/O EXPANDER OVER CURRENT PROT IC8301 CVBS1 Q1326, IC8200 Q1327 CN8900 MAIN COLOR DECODER BUFFER CVBS2 OV PROT...
  • Page 33 5-1. BLOCK DIAGRAMS (3) CN6601 (1/2) CN6622 ABL1 CN6601 (2/2) SWITCH CN502 HD2OUT IC801 IC303 Q6104 (1/2) Q6106 H PULSE SUB IN V PULSE SUB IN VDOCLKIN H PULSE SUB IN VP100 IC304 V PULSE SUB IN XDSPVS SUB A/D IC6102 V SUB IN HP100...

  • Page 34: Schematic Diagrams And

    5-1. BLOCK DIAGRAMS (4) IC9109 IC9105 MAIN MICRO-CONTROLLER PROGRAMMABLE O.T.P. CN9101 SCLO CN4101 5-2. CIRCUIT BOARD LOCATION Reference Information A(19) SCLO SWITCH A(19) Q9108,9109 A(18) EXTRA PARABOLA A(18) EXTRA PARA SCL1 A(17) A(18) TO D BOARD A(17) +12V POWER ON SWITCH IC5300 D FOCUS Q5350...
  • Page 35 [ IR RECEIVER FOR SIRCS AND LED ] [ POWER SWITCH ] [ FRONT AV, S-VIDEO ] [ PRINTED WIRING BOARD ] [ PRINTED WIRING BOARD ] [ AC FILTER FUSE ] [ PRINTED WIRING BOARD ] [ PRINTED WIRING BOARD ]...
  • Page 36 [ R, G, B OUT CHROMA ]...
  • Page 37 [ PRINTED WIRING BOARD (A side) ] [ PRINTED WIRING BOARD (B side) ]...
  • Page 38 [ PRINTED WIRING BOARD (A side) ] [ PRINTED WIRING BOARD (B side) ]...
  • Page 39 [ MICRO PROCESSOR AND TEXT DECODER]...
  • Page 40 [ DEFLECTION ]...
  • Page 41 [ PRINTED WIRING BOARD ]...
  • Page 42 D board Waveforms 5ms/div 5ms/div 570 mVp-p (V) 58 Vp-p (V) 10us/div 10us/div 2.28 Vp-p (H) 131 Vp-p (H) 10us/div 10us/div 2.14 Vp-p (H) 150 Vp-p (H) 10us/div 20us/div 1.07 kVp-p (H) 2.3 Vp-p (H) 10us/div 10us/div TP10 1.72 kVp-p (H) 265 Vp-p (H) 5ms/div 5ms/div...
  • Page 43 [ POWER SUPPLY AND DEFLECTION ]...
  • Page 44 [ SIGNAL AND AUDIO AMPLIFIER ]...
  • Page 45 IC Voltage Table Semiconductor Location Table Semiconductor Voltage Table [ PRINTED WIRING BOARD ]...
  • Page 46 Semiconductor Location Table IC Voltage Table Semiconductor Voltage Table [ PRINTED WIRING BOARD ]...
  • Page 47 [ INTERFACE, AUDIO, CHROMA, COMB FILTER (Page 1/2) ]...
  • Page 48 [ INTERFACE, AUDIO, CHROMA, COMB FILTER (Page 2/2) ]...
  • Page 49 C board Waveforms 5us/div 10us/div 117 Vp-p (H) 109 Vp-p (H) 10us/div 10us/div 109 Vp-p (H) 2.5 Vp-p (H) 10us/div 5us/div 2.5 Vp-p (H) 2.5 Vp-p (H) 10us/div 3.64 Vp-p (H) [ PRINTED WIRING BOARD ]...
  • Page 50 [ PRINTED WIRING BOARD [A] SIDE ] [ PRINTED WIRING BOARD [B] SIDE ]...
  • Page 51 [ ANALOGUE NOISE REDUCTION ]...
  • Page 52 [ 100Hz PROCESSING (Page 1/6) ] [ PRINTED WIRING BOARD [A] SIDE ] [ PRINTED WIRING BOARD [B] SIDE ]...
  • Page 53 [ 100Hz PROCESSING (Page 2/6) ]...
  • Page 54 [ 100Hz PROCESSING (Page 3/6) ]...
  • Page 55 [ 100Hz PROCESSOR (Page 4/6) ]...
  • Page 56 [ 100Hz PROCESSOR (Page 5/6) ]...
  • Page 57 [ 100Hz PROCESSOR (Page 6/6) ]...

  • Page 58: Semiconductors

    [ VELOCITY MODULATION ] [ PRINTED WIRING BOARD ] VM board Waveforms 10us/div 10us/div 20us/div 117 Vp-p (V) 109 Vp-p (V) 109 Vp-p (V) Semiconductor Voltage Table 5-4 SEMICONDUCTORS 5-5. IC BLOCK DIAGRAMS U2860B-BFPG3 IMZ1A-T109 2SC2500-B TDA9320H-N1-518 74LVC08D 2SC2551-O MSP3410D-QA-B4 BA7046F KA78R05TU STV9379...
  • Page 59 D4SB60L DAN202K UF4005PKG23 ESAC39M-06C D4SB60L-F DAN202K-T-146 ESAC39M-06CF38 RBA-402L ANODE CATHODE DAP202K DAP202K-T-146 ERA38-06TP1 MTZJ-T-77-9.1 ERA82-004TP1 MTZJ-T-77-12 GP08DPKG23 MTZJ-T-77-22 MA3033-L MTZJ-T-77-12 MTZJ-T-77-18B MA3033L-TX MTZJ-T-77-15 MTZJ-33C MA3056M-TX MTZJ-T-77-2.2A RD5.6ESB2 MA3062M-TX MTZJ-T-77-3-3B RD9.1ESB2 MA3030-H-(TX) MTZJ-T-77-3.6A PGKE200AG23 MTZJ-T-77-4.7B 1SS119-25 DA204K MTZJ-T-77-5.6B 1SS119-25TD DA204K-T-146 MTZJ-T-77-6.8 MTZJ-T-77-7.5B CATHODE MA3051L-TX...

  • Page 60: Exploded Views

    SECTION 6 EXPLODED VIEWS NOTE : • Items with no part number and no description are not • Items marked “ * “ are not stocked stocked because they are seldom required for routine since they are seldom required for service.
  • Page 61 REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK *A-1646-211-A H6 BOARD, COMPLETE 7-685-663-71 SCREW + BVTP 4X16 TYPE IT-3 1-542-437-11 TWEETER 1-529-417-11 SPEAKER (8CM) 1-542-436-11 SPEAKER 4-204-776-01 BOX, WOOFER *A-1678-191-A WOOFER ASSY (SP) 26-29 4-205-448-01 COVER, REAR 4-204-775-01 BAFFLE, WOOFER 7-685-663-79 SCREW + BVTP 4X16 TYPE 2 IT-3...

  • Page 62: Picture Tube

    6-2. PICTURE TUBE REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK X-4200-603-1 BEZNET ASSY *A-1644-108-A VM BOARD, COMPLETE A-1610-067-A FRONT CONTROL ASSY 53-61 *A-1638-139-A C BOARD, COMPLETE *4-205-460-01 BRACKET, CONTROL 4-369-318-21 SPRING, TENSION 4-205-463-01 WINDOW, ORNAMENTAL £ 1-416-654-11 COIL, DEMAGNETIC 4-047-464-01 CATCHER, PUSH 4-203-390-11 CUSHION, DGC *4-205-461-01 BRACKET DOOR...

  • Page 63: Electrical Parts List

    SECTION 7 ELECTRICAL PARTS LIST PARTS LISTING TABLE OF CONTENTS Page F3 BOARD COMPLETE Parts List : ....................114 H5 BOARD COMPLETE Parts List : ....................114 H6 BOARD COMPLETE Parts List : ....................114 BL BOARD COMPLETE Parts List : ....................
  • Page 64 The components identified by shading and marked are critical for safety F3 H5 H6 BL Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK < SWITCH > *A-1624-085-A F3 Board, Complete < CONNECTOR > S7100 1-771-947-11 SWITCH, TACTILE S7101...
  • Page 65 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK C2323 1-163-038-91 CERAMIC CHIP 0.1UF C2533 1-126-964-11 ELECT 10UF 20.00% 50V C2324 1-163-038-91 CERAMIC CHIP 0.1UF C2535 1-104-664-11 ELECT...
  • Page 66 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK IC2505 8-752-072-94 IC CXA1875AM-T4 Q2338 8-729-216-22 TRANSISTOR 2SA1037K-T-146-R Q2339 8-729-120-75 TRANSISTOR 2SC2412K-T-146-QR <...
  • Page 67 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK < RESISTOR > R2355 1-216-017-91 RES-CHIP 1/10W R2356 1-216-049-91 RES-CHIP 1/10W R2301 1-216-017-91 RES-CHIP 1/10W R2357...
  • Page 68 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R2424 1-216-039-00 RES-CHIP 1/10W R2545 1-216-623-91 METAL CHIP 0.5% 1/10W R2425 1-216-041-00 RES-CHIP 1/10W R2546 1-216-655-91 METAL CHIP...
  • Page 69 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R2593 1-216-055-00 RES-CHIP 1.8K 5% 1/10W C325 1-163-021-91 CERAMIC CHIP 0.01UF 10.00% 50V R2594 1-216-643-11 METAL CHIP 0.5% 1/10W...
  • Page 70 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK C527 1-164-004-11 CERAMIC CHIP 0.1UF 10.00% 25V C626 1-163-021-91 CERAMIC CHIP 0.01UF 10.00% 50V C528 1-163-021-91 CERAMIC CHIP 0.01UF...
  • Page 71 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK C834 1-163-038-91 CERAMIC CHIP 0.1UF FL504 1-234-177-21 FILTER, CHIP EMI C835 1-163-038-91 CERAMIC CHIP 0.1UF FL505 1-234-177-21 FILTER, CHIP EMI C837...
  • Page 72 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK IC802 8-759-595-53 IC MB81F643242B-10FN Q909 8-729-216-22 TRANSISTOR 2SA1037K-T-146-R IC901 8-752-369-84 IC CXD2309Q-T6 <...
  • Page 73 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R513 1-216-043-91 RES-CHIP 1/10W R594 1-216-041-00 RES-CHIP 1/10W R514 1-216-043-91 RES-CHIP 1/10W R596 1-216-049-91 RES-CHIP 1/10W...
  • Page 74 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R667 1-216-663-11 METAL CHIP 3.3K 0.5% 1/10W R824 1-216-073-00 RES-CHIP 1/10W R668 1-216-009-91 RES-CHIP 1/10W R825...
  • Page 75 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R883 1-216-009-91 RES-CHIP 1/10W R981 1-216-037-00 RES-CHIP 1/10W R884 1-216-009-91 RES-CHIP 1/10W R982 1-216-037-00 RES-CHIP 1/10W...
  • Page 76 The components identified by shading and marked are critical for safety B3 F1 Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK RB015 1-239-621-11 NETWORK RESISTOR (CHIP) 22 < TRANSFORMER > RB016 1-239-621-11 NETWORK RESISTOR (CHIP) 22 RB017 1-239-621-11 NETWORK RESISTOR (CHIP) 22...
  • Page 77 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK C1180 1-126-952-11 ELECT 1000UF 20.00% 35V CN1901 1-695-298-11 CONNECTOR, BOARD TO BOARD 40P C1181 1-126-952-11 ELECT 1000UF...
  • Page 78 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK IC1601 8-759-574-76 IC KA78R05-SYDTU < RESISTOR > IC1604 8-759-544-13 IC KA78R09-YDTU IC1605 8-759-574-76 IC KA78R05-SYDTU JR1203 1-216-296-91 SHORT...
  • Page 79 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R1232 1-216-295-91 SHORT R1424 1-216-045-00 RES-CHIP 1/10W R1233 1-216-049-91 RES-CHIP 1/10W R1425 1-216-025-91 RES-CHIP 1/10W R1300...
  • Page 80 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK C9129 1-163-105-00 CERAMIC CHIP 33PF 5.00% 50V IC9107 8-759-395-27 IC TC55257DFTL-70V-EL C9130 1-163-105-00 CERAMIC CHIP 33PF 5.00% 50V IC9108...
  • Page 81 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R9116 1-216-073-00 RES-CHIP 1/10W R9194 1-216-097-91 RES-CHIP 100K 5% 1/10W R9117 1-216-073-00 RES-CHIP 1/10W R9195 1-216-097-91 RES-CHIP...
  • Page 82 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK C5304 1-107-967-11 ELECT 20.00% 400V D5351 8-719-991-33 DIODE 1SS133T-77 C5305 1-136-207-11 MYLAR 0.047UF 10.00% 400V D5353...
  • Page 83 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R5309 1-216-658-11 METAL CHIP 0.5% 1/10W *A-1640-318-A D Board, Complete R5310 1-216-059-00 RES-CHIP 2.7K 5% 1/10W R5325...
  • Page 84 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK C6653 1-126-968-11 ELECT 100UF 20.00% 50V C6816 1-130-471-00 MYLAR 0.001UF 5.00% 50V C6654 1-162-117-00 CERAMIC 100PF...
  • Page 85 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK D6602 8-719-109-89 DIODE MTZJ-T-77-5.6B D6851 8-719-970-87 DIODE ERA38-06TP1 D6603 £ 8-719-921-19 DIODE 1SS119-25TD D6852 8-719-970-87 DIODE ERA38-06TP1 D6604...
  • Page 86 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK < TRANSISTOR > R6626 1-247-807-31 CARBON 1/4W R6627 1-249-429-11 CARBON 1/4W Q6600 8-729-046-47 TRANSISTOR KSC2500-BTA R6628 1-260-129-11 CARBON...
  • Page 87 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R6692 1-215-445-00 METAL 1/4W R6845 1-247-863-91 CARBON 1/4W R6700 1-215-441-00 METAL 6.8K 1% 1/4W R6851 1-260-123-11 CARBON...
  • Page 88 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK C6258 1-163-127-00 CERAMIC CHIP 270PF 5.00% 50V *A-1640-380-A D1 Board, Complete C6259 1-110-501-11 CERAMIC CHIP 0.33UF 10.00% 16V 4-202-554-01 HOLDER, HV CABLE...
  • Page 89 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK < CONNECTOR > IC6353 8-759-231-53 IC L7805CV IC6354 8-759-325-48 IC CA0005AD CN6502 *1-568-881-51 PIN, CONNECTOR 6P IC6355 8-759-008-70 IC LM358N...
  • Page 90 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK Q6356 8-729-120-28 TRANSISTOR 2SC2412K-T-146-R R6137 1-216-691-11 METAL CHIP 0.5% 1/10W Q6358 8-729-038-83 TRANSISTOR 2SK2251-01-F19 R6138 1-216-691-11 METAL CHIP 0.5% 1/10W...
  • Page 91 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R6210 1-216-057-00 RES-CHIP 2.2K 5% 1/10W R6358 1-216-047-91 RES-CHIP 1/10W R6211 1-216-073-00 RES-CHIP 1/10W R6359 1-216-097-91 RES-CHIP...
  • Page 92 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R6415 1-216-683-11 METAL CHIP 0.5% 1/10W C4331 1-126-959-11 ELECT 0.47UF 20.00% 50V R6416 1-216-683-11 METAL CHIP 0.5% 1/10W...
  • Page 93 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK D4312 8-719-914-43 DIODE DAN202K-T-146 R4331 1-216-073-00 RES-CHIP 1/10W D4313 8-719-401-63 DIODE MA3062M-TX R4332 1-216-073-00 RES-CHIP 1/10W...
  • Page 94 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R4394 1-216-025-91 RES-CHIP 1/10W C8211 1-163-243-11 CERAMIC CHIP 47PF 5.00% 50V R4395 1-216-295-91 SHORT C8212 1-163-243-11 CERAMIC CHIP 47PF...
  • Page 95 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK C8324 1-164-004-11 CERAMIC CHIP 0.1UF 10.00% 25V C8507 1-164-004-11 CERAMIC CHIP 0.1UF 10.00% 25V C8325 1-126-964-11 ELECT...
  • Page 96 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK C8827 1-164-004-11 CERAMIC CHIP 0.1UF 10.00% 25V C8902 1-163-017-00 CERAMIC CHIP 0.0047UF 10.00% 50V C8828 1-164-004-11 CERAMIC CHIP 0.1UF...
  • Page 97 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK D8813 8-719-158-49 DIODE UDZ-TE-17-12B IC8302 8-759-485-79 IC TC7SET08FU(TE85R) D8814 8-719-158-49 DIODE UDZ-TE-17-12B IC8401 8-752-096-08 IC CXA2123BQ-T6 D8900...
  • Page 98 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK Q8501 8-729-216-22 TRANSISTOR 2SA1037K-T-146-R R8167 1-216-025-91 RES-CHIP 1/10W Q8503 8-729-216-22 TRANSISTOR 2SA1037K-T-146-R R8168 1-216-025-91 RES-CHIP 1/10W...
  • Page 99 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R8306 1-216-083-00 RES-CHIP 1/10W R8417 1-216-081-00 RES-CHIP 1/10W R8307 1-216-049-91 RES-CHIP 1/10W R8418 1-216-295-91 SHORT R8308...
  • Page 100 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R8703 1-216-025-91 RES-CHIP 1/10W R8888 1-216-033-00 RES-CHIP 1/10W R8704 1-216-025-91 RES-CHIP 1/10W R8889 1-216-033-00 RES-CHIP 1/10W...
  • Page 101 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R8945 1-216-022-00 RES-CHIP 1/10W *A-1644-108-A VM Board, Complete R8946 1-216-017-91 RES-CHIP 1/10W R8947 1-216-039-00 RES-CHIP 1/10W...
  • Page 102 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK < TRANSISTOR > MISCELLANEOUS Q5400 8-729-119-78 TRANSISTOR 2SC1740S-RT £ 1-416-654-11 COIL DEMAGNETIC Q5401 8-729-119-78 TRANSISTOR 2SC1740S-RT 1-452-032-00 MAGNET, DISK;...
  • Page 104 • User programmable Functional Check through Infrared • Fast and documented Test Mode setting of all Sony TV chassis Additional features such as Adjustments and Troubleshooting are available in chassis-dependent software modules. Please contact your local Sony Service organisation for the latest information.

This manual is also suitable for:

Fd triniton kv-29fq75dFd triniton kv-29fq75eFd triniton kv-29fq75k

Table of Contents