Motorola MH Series User Manual

Body-Worn Operation
To maintain compliances with FCC/Health Canada RF exposure
®
guidelines if you wear a radio on your body when transmitting
always place the radio in a Motorola-supplied or approved clip
holder, holster, case or body harness for this product. Use of non-
Two-Way Radio
Motorola-approved accessories may exceed FCC/Health Canada RF
exposure guidelines.
User's Guide
If you do not use one of the Motorola-supplied or approved body-
worn accessories and are not using the radio held in the normal
use position, ensure the radio and its antenna are at least 1 inch
(2.5 cm) from your body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or
without an accessory cable, position the radio and its antenna at
least one inch (2.5 cm) from the body.
Approved Accessories
For a list of approved Motorola accessories, visit our Web site at
www.motorola.com.
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to
electromagnetic interference (EMI) if inadequately shielded,
designed or otherwise configured for electromagnetic compatibility.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including
interference that may cause undesired operation.
KEM PK14190 75 MH Series
IC Canada
The term "IC:" before the equipment certification number only
signifies that the Industry Canada technical specifications were met.
For More Information Facilities
To avoid electromagnetic interference and/or compatibility conflicts,
For further information, you may call Motorola at 1-800-638-5119
turn off your radio in any facility where posted notices instruct you
(U.S. and Canada), or e-mail us at giantintl@callcenter.com or visit
to do so. Hospitals or health care facilities may be using equipment
us on the Internet at www.motorola.com.
that is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when onboard an
Safety and General Information
aircraft. Any use of a radio must be in accordance with applicable
regulations per airline crew instructions.
Important Information on Safe and Efficient Operation
Medical Devices – Pacemakers
Read This Information Before Using Your Radio.
The Advanced Medical Technology Association recommends that
The information provided in this document supersedes the general a minimum separation of 6 inches (15 cm) be maintained between a
safety information in user guides published prior to December 1, 2002.
handheld wireless radio and a pacemaker. These recommendations
are consistent with the independent research by and
Transmit and Receive Procedure
recommendations of the U.S. Food and Drug Administration.
Your two-way radio contains a transmitter and a receiver. To control
your exposure and ensure compliance with the general population/ People with pacemakers should:
uncontrolled environment exposure limits, always adhere to the
• ALWAYS keep the radio more than 6 inches (15 cm) from their
following procedure:
pacemaker when the radio is turned ON.
• Transmit no more than 50% of the time.
• Not carry the radio in the breast pocket.
• To receive calls, release the PTT button.
• Use the ear opposite the pacemaker to minimize the potential
• To transmit (talk), press the Push to Talk (PTT) button. for interference.
Transmitting 50% of the time, or less, is important because the radio • Turn the radio OFF immediately if there is any reason to suspect
generates measurable RF energy exposure only when transmitting that interference is taking place.
(in terms of measuring standards compliance).
Medical Devices – Hearing Aids
Exposure to Radio Frequency Energy Some digital wireless radios may interfere with some hearing aids.
In the event of such interference, you may want to consult your
Your Motorola two-way radio complies with the following RF energy
exposure standards and guidelines: hearing aid manufacturer to discuss alternatives.
• United States Federal Communications Commission, Code of Medical Devices – Other
Federal Regulations; 47CFR part 2 sub-part J.
If you use any other personal medical device, consult the
manufacturer of your device to determine if it is adequately
• American National Standards Institute (ANSI)/Institute of
shielded from RF energy. Your physician may be able to assist you
Electrical and Electronic Engineers (IEEE) C95. 1-1992.
in obtaining this information.
• Institute of Electrical and Electronics Engineers (IEEE) C95.
1-1999 Edition.
Safety and General Use While Driving
Check the laws and regulations regarding the use of radios in the
• International Commission on Non-Ionizing Radiation Protection
area where you drive, and always obey them. If you do use your
(ICNIRP) 1998.
radio while driving, please:
• Ministry of Health (Canada) Safety Code 6. Limits of Human
Exposure to Radiofrequency Electromagnetic Fields in the • Give full attention to driving and to the road.
Frequency Range from 3 KHz to 300 GHz, 1999.
• Use hands-free operation, if available.
• Australian Communications Authority Radiocommunications
• Pull off the road and park before making or answering a call if
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
driving conditions so require.
• ANATEL ANNEX to Resolution No. 303 of July 2, 2002 "Regulation of
The use of a two-way radio while engaged in activities requiring
limitation of exposure to electrical, magnetic and electromagnetic
concentration may cause distraction or otherwise impair your
fields in the radio frequency range between 9 KHz and 300GHz".
ability to safely participate in such activities. Always use technology
safely.
To ensure optimal radio performance and make sure human
exposure to radio frequency electromagnetic energy is within the
Do not place a portable radio in the area over an air bag or in the
guidelines set forth in the above standards, always adhere to the
air bag deployment area. Air bags inflate with great force. If a
following procedures.
portable radio is placed in the air bag deployment area and the air
bag inflates, the radio may be propelled with great force and cause
Portable Radio Operation and EME Exposure
serious injury to occupants of the vehicle.
Antenna Care
Potentially Explosive Atmospheres
Use only the supplied or an approved replacement antenna.
Turn off your radio prior to entering any area with a potentially
Unauthorized antennas, modifications, or attachments could
explosive atmosphere. Only radio types that are especially qualified
damage the radio and may violate FCC regulations.
should be used in such areas as "Intrinsically Safe." Do not remove,
Do NOT hold the antenna when the radio is "IN USE." Holding the
install or charge batteries in such areas. Sparks in a potentially
antenna affects its effective range.
explosive atmosphere can cause an explosion or fire resulting in
bodily injury or even death.
Note: The areas with potentially explosive atmospheres referred to
above include fueling areas such as below decks on boats, fuel or
chemical transfer or storage facilities, areas where the air contains
chemicals or particles (such as grain, dust or metal powders) and
any other area where you would normally be advised to turn off your
vehicle engine. Areas with potentially explosive atmospheres are
Volume
often—but not always—posted.
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your
radio when you are near electrical blasting caps, in a blasting area,
Push to Talk
or in areas posted "Turn off two-way radios." Obey all signs and
instructions.
Operational Cautions
Antennas
Call Tone
Do not use any portable radio that has a damaged antenna. If a
damaged antenna comes into contact with your skin, a minor burn
can result.
Batteries
Speaker
All batteries can cause property damage and/or bodily injury such as
burns if a conductive material—like jewelry, keys or beaded chains—
touch exposed terminals. The conductive material may complete an
electrical circuit (short circuit) and become quite hot. Exercise care in
Mini-USB
handling any charged battery, particularly when placing it inside a
Charging Port
pocket, purse or other container with metal objects.
Exercise care when removing NiMH or AAA batteries. Do not use
sharp or conductive tools to remove either of these batteries.
Battery Charger Safety Instructions:
Save these Instructions
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received a
Numbers
sharp blow, or has been dropped or damaged in any way.
for Channel,
3. Never alter the AC cord or plug provided with the unit. If the Call Tone
plug will not fit the outlet, have the proper outlet installed by a
Numbers
qualified electrician. An improper condition can result in a risk
for Codes
of electric shock.
4. To reduce the risk of damage to the cord or plug, pull the plug
- Battery Meter
rather than the cord when disconnecting the charger from the
AC receptacle.
- Channel Power
5. To reduce the risk of electric shock, unplug the charger from the
Indicator (see
outlet before attempting any maintenance or cleaning.

Menu Options)

6. Use of an attachment not recommended or sold by Motorola
may result in a risk of fire, electric shock or personal injury.
- Lock
7. Make sure the cord is located so it will not be stepped on,
tripped over or subjected to damage or stress.
- Talk Confirmation
8. An extension cord should not be used unless absolutely
Tone (Roger Beep)
necessary. Use of an improper extension cord could result in a
risk of a fire and/or electric shock. If an extension cord must be
- Noise Filtering
used, make sure that:
• The pins on the plug of the extension cord are the same
number, size and shape as those on the plug of the charger.
• The extension cord is properly wired and in good electrical
condition.
Installing the Batteries
• The extension cord size is 18 AWG for lengths up to 100 feet,
Each radio uses 1 NiMH rechargeable battery pack or 3 AAA
and 16 AWG for lengths up to 150 feet.
alkaline batteries and beeps when the batteries are low.
9. The supply cord of the AC adaptor cannot be replaced. If the
Installing NiMH Rechargeable Battery Pack (Optional Accessory)
cord is damaged, call customer service at 1-800-638-5119 (U.S.
1. Turn the radio off.
and Canada) or e-mail us at giantintl@callcenter.com.
2. With the back of the radio facing you, lift the battery cover latch
up and remove the cover.
FCC Licensing Information
3. Remove the battery pack from the clear plastic bag. (Do not
disassemble or unwrap the battery pack.)
Your Motorola radio operates on General Mobile Radio Service
4. Insert the NiMH battery pack with the diagram facing you.
(GMRS) frequencies and is subject to the Rules and Regulations of
the Federal Communications Commission (FCC). The FCC requires
5. Reposition the battery cover and press down to secure.
that all operators using GMRS frequencies obtain a radio license
Installing the Three AAA Alkaline Batteries
before operating their equipment. To obtain the FCC forms, please
1. Turn the radio off.
visit the FCC's Web site at wireless.fcc.gov/uls/index.htm?job=home
2. With the back of the radio facing you, lift the battery cover latch
to source form 605 and 159, which includes all the instructions you
up and remove the cover.
will need.
3. Insert the three AAA alkaline batteries with + and - polarity as
If you wish to have the document faxed or mailed, or if you have
shown inside.
questions, please use the following contact information:
4. Reposition the battery cover and press down to secure.
For a fax: For mail service: If you have
Radio Battery Meter
Contact the Call the FCC questions about
The radio battery icon shows the radio battery charge level, from
Fax-0n-Demand Forms Hotline the FCC License:
full to empty
system Call the FCC
radio chirps periodically or after releasing
1-202-418-0177 1-800-418-FORM 1-888-CALL-FCC
Removing the NiMH Battery Pack (Optional Accessory)
(3676) (225-5322)
1. Turn the radio off.
Changes or modifications not expressly approved by Motorola may 2. With the back of the radio facing you, lift the battery latch up to
void the user's authority granted by the FCC to operate this radio
release the battery cover and remove the cover.
and should not be made. To comply with FCC requirements,
3. Remove the NiMH battery pack by pulling the ribbon attached to
transmitter adjustments should be made only by or under the
the battery.
supervision of a person certified as technically qualified to perform
4. Reposition the battery cover and press down to secure.
transmitter maintenance and repairs in the private land mobile and
Removing the Three AAA Batteries
fixed services as certified by an organization representative of the
user of those services. Replacement of any transmitter component 1. Turn the radio off.
(crystal, semiconductor, etc.) not authorized by the FCC equipment
2. With the back of the radio facing you, lift the battery latch up to
authorization for this radio could violate FCC rules.
release the battery cover and remove the cover.
3. Gently remove each battery by easing each battery out individually.

Control Buttons

4. Reposition the battery cover and press down to secure.
Notes
• Exercise care when removing NiMH or AAA batteries. Do not
use sharp or conductive tools to remove either of these batteries.
Menu/Lock
• Remove the batteries before storing your radio for extended
periods of time. Batteries corrode over time and may cause
permanent damage to your radio.
Using the Battery Charger (Optional Accessory)
The battery charger provides drop-in charging convenience for
NiMH batteries and can be placed on any flat surface, such as a
Accessory Jack
desk or workbench. Charge the NiMH battery overnight (at least
16 hours) before using it for the first time. After the initial charge,
an empty battery is fully charged within 14 hours.
Scan/Monitor
1. Follow the steps above to install a NiMH Battery Pack.
2. Plug the AC power supply cord into the jack on the desk stand.
3. Plug the AC power supply into a standard wall outlet.
4. With a radio facing forward, slide it into one of the charging
pockets.
Scroll/Weather
5. When charging in the battery charger, the red light on the
charger base will glow continuously.
Using the mini-USB Charging Connector
Microphone
The mini-USB charging connector is a handy port that allows you to
conveniently charge your NiMH battery pack. This is an alternative
to charging your NiMH battery pack in the Battery Charger desk

Display Screen Guide

stand using the AC wall adaptor and especially useful when used
while traveling.
Available mini-USB charging options: (Optional Accessories)
1. Wall travel charger
2. Vehicle charger
3. Mini-USB computer cable
If using a computer, the computer must be turned on.
On/Off for each
-
This and other accessories (sold separately) are available for
feature
your radio. For more information, visit our Web site at
www.motorola.com or shop.giantintl.com.
- Scan
1. Plug your mini-USB cable or charger into a power source as is
appropriate for your accessory.
- Call Tone,
2. Plug the cable into the mini-USB port on the bottom of your radio.
Keypad Tone
3. An empty battery will be fully charged in 14 hours.
4. The LED indicator light on the radio will glow to indicate that the
- Weather Alert
battery is charging.
Notes
- Hands-Free Use
• The light will remain red after the NiMH battery pack is fully
Without
charged.
Accessories
• When moving between hot and cold temperatures, do not
charge the NiMH battery pack until the battery temperature
- Hands-Free Use
acclimates (usually about 20 minutes).
With Accessories
• For optimal battery life, remove the radio from the charger within
16 hours. Do not store the radio while connected to the charger.
Getting Started
• If the radio is kept on while charging, the charging time will be
extended.
• Even though the charger is connected, you may not be able to
transmit a message if the battery is completely empty
Allow time for the battery to charge to 1 bar
attempting to transmit a message.
Attaching and Removing the Belt Clip
1. Attach belt clip to pocket or belt strap.
2. Align the belt clip post with the hole in the back of the radio.
3. Gently push until the clip clicks in place.
To Remove
1. Push down on the release tab at the top of the belt clip to
release the catch.
2. Pull the belt clip away from the back of the radio.
Turning your Radio On and Off
Turn clockwise to turn the radio on and counterclockwise to
turn the radio off.
1. In the ON position, the radio chirps and briefly shows all feature
icons available on the radio.
2. The display screen then shows the current channel, code and
all features that are enabled.
Setting the Volume
. When the radio has one segment left, the
Press and hold for three seconds while rotating
(Low Battery Alert).
reach a comfortable listening level.
1. Rotate clockwise to increase the volume.
2. Rotate counterclockwise to decrease the volume.
Do not hold the radio close to your ear. If the volume is set to an
uncomfortable level, it could hurt your ear.
Talking and Listening
To communicate, all radios in your group must be set to the same
channel and Interference Eliminator Code.
1. To talk, press and hold .
2. When you are finished talking, release
For maximum clarity, hold the radio two to three inches away from
your mouth and speak directly into the microphone. Do not cover
the microphone while talking.
Talk Range
Your radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet apart.
Monitor Button
Pressing and holding for three seconds allows you to listen to
the volume level of the radio when you are not receiving. This allows
you to adjust the volume, if necessary. You can also press
check for activity on the current channel before you talk.
Push to Talk Timeout Timer
To prevent accidental transmissions and save battery life, the radio
emits a continuous warning tone and stops transmitting if you
press for 60 continuous seconds.

Menu Options

Selecting the Channel
Your radio has 22 channels. The channel is the frequency the radio
uses to transmit. Channels 8-14 are FRS 0.5 watt only and all other
channels are GMRS. (See the "Channels and Frequencies" table on
overleaf for details.)
1. With the radio on, press . When the radio is on a 0.5 watt
channel, displays. When the radio is on a 1 watt channel,
displays. The current channel flashes.
2. Press or and select an unused or quiet channel.
3. Press to save the channel setting or to continue set up.
Selecting the Interference Eliminator Code
Interference Eliminator Codes help minimize interference by
blocking transmissions from unknown sources. Your radio has 121
Interference Eliminator Codes. Codes 1 – 38 are the standard analog
codes that appear on other FRS/GMRS radios. Codes 39 – 121 are
additional digital codes added for superior interference protection.
0 is the off position, no analog or digital codes are enabled.
To set the code for a channel:
1. Press until the code starts to flash.
2. Press or to select the code.
3. Press to save the code setting or to continue set up.
You can set a different code for each channel using this procedure.
An extended press of or allows you to scroll through
the Interference Code rapidly so you can quickly reach the code
you want.
Note: You must set the Interference Eliminator Code to 0 on a radio
that uses Interference Eliminator Codes to communicate with radios
that do not have Interference Eliminator Codes. Select 0 for "no
tone, no code" and OFF will flash on your radio's display.
Setting and Transmitting Call Tones
Your radio can transmit different call tones to other radios in your
group so you can alert them that you want to talk. You have 10 call
tones from which to choose.
To set a call tone:
.
1. With the radio on, press three times until the current
before
call tone setting (0 - 10) flashes and appears.
2. Press or to change and hear the call tone.
3. Press to set the new call tone or to continue set up.
To transmit your call tone to other radios set to the same channel
and Interference Eliminator Code as your radio, press
Note: Setting the call to 0 disables the call tone feature.
Hands-Free Use Without Accessories ( )
You can use the iVOX feature to transmit hands-free without the need
for any headset accessories. Once iVOX is turned on, the radio detects
your voice and transmits when you speak into the internal microphone.
1. Press until appears on the display. The current
setting On/Off will flash.
2. Press or to select On or Off.
3. Press to set or to continue set up.
Hands-Free Use With Accessories ( )
You can transmit hands-free more reliably with the use of optional
until you headset accessories. Once VOX is turned on, the radio detects your
voice and transmits when you speak.
Many accessories (sold separately) are available for your radio.
For more information, visit our Web site at www.motorola.com or
shop.giantintl.com.
1. Turn the radio off and plug the VOX accessory into the
accessory port.
2. Turn the radio on. VOX shows on the display.
3. Adjust the volume appropriately by rotating . Lower the
volume before placing the accessory on your head or in your ear.
4. To turn off, simply remove accessory.
Continued on back
.
to
.
MH Series