Table of Contents
Advertisement
Quick Links
Advertisement
Chapters
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Link HD8X8
Summary of Contents for Link HD8X8
- Page 1 H D 8 X 8 H D 8 X 8 USER MANUAL www.mstrbrand.com...
-
Page 2: Table Of Contents
S A F E T Y & N O T I C E The LINK HD8X8 8x8 HDMI Matrix Switcher with Full 3D Support has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipment, the HD8X8 should be used with care. -
Page 3: Introduction
I N T R O D U C T I O N The HD8X8 8x8 HDMI Non-UTP Matrix provides the most flexible and cost effective solution in the market to route high definition video source plus multi-channel (up to 7.1-channel) digital audio from any of the four HDMI sources to the remote displays at the same time. -
Page 4: Specifications
HDMI compliance HDMI Deep Color & full 3D HDCP compliance Video bandwidth Single -link 225MHz [6.75Gbps] Video support 480i / 480p / 720p / 1080i / 1080p60 36 -bit color Audio support Surround sound (up to 7.1ch) or stereo digital audio [1] Human body model ±19kV [air -gap discharge] &... -
Page 5: Panel Descriptions
P A N E L D E S C R I P T I O N S FRONT PANEL 1. PORT SELECT OUTPUT 1~8: Push round button 1~8 for selecting output source channels. Round button shows blue light after selecting. 2. -
Page 6: Hardware Installation
2. Connect all displays to HDMI Outputs on the 8X8 HDMI Matrix HD8X8. 3. Connect the +12V 5A DC power supply to the 8x8 HDMI Matrix HD8X8. C O N N E C T I O N D I A G R A M... -
Page 7: Operation Approach
O P E R A T I O N A P P R O A C H M E T H O D A : P U S H - I N B U T T O N 1. Push output round button for selecting output source channels. Round button shows blue light after selecting. - Page 8 M E T H O D B : I R R E M O T E C O N T R O L 1. IN/OUT SWITCH Operation Procedure 7-Segment LED IN/OUT Switch Output Number (1~8 ) + In put Number (1~8 ) 1.
- Page 9 2. FUNCTION KEY Button Function Standby mode Power on the matrix switcher MUTE Turn o output s video and audio STATUS Preset output status SAVE Save current mapping mode PRESET Preset mapping mode DEFAULT EDID Begin default EDID selection LEARN EDID Begin EDID learning from one output CLEAR Clear the previous IR operation procedure...
- Page 10 Operation Procedure 7-Segment LED Output Status Status + Output Number (1~8) + Take 1.Press STATUS button Ex: Output 4 2.Press output number key 4 to select Output 4 (Input 2) 3.Press TAKE button Save Current Mapping Save + Output Number (1-8 storage site) + Take 1.Press SAVE button...
- Page 11 M E T H O D C : S O F T W A R E C O N T R O L T H R O U G H R S - 2 3 2 P O R T / E T H E R N E T P O R T 1.
-
Page 12: O Routing Button
1. I/O ROUTING BUTTON 1) I/O: a) Select the input b) Click “Send” to change the I/O setting 2) Save Mapping: a) Select Mapping (1-8) b) Click “Save” button to save current mapping 3) Preset Mapping: a) Select Mapping (1-8) a) Click “Recall”... -
Page 13: Rename I/O Button
2. RENAME I/O BUTTON 1) Rename I/O: a) Rename output name b) Rename input name 2) Rename Mapping: a) Rename Mapping name... -
Page 14: Edid Button
3. EDID BUTTON 1) Learn EDID from Default a) Select Default EDID (1-8 Default EDID) b) Select Input c) Click “Send” button to learn default EDID 2) Learn EDID From Display a) Select output b) Select Input c) Click “Send” button to learn display EDID 3) Load EDID File to Input a) Select Input b) Click “Load”... -
Page 15: Network Button
b) Select the EDID content c) Click “Save EDID on Computer” to save the generated EDID as a file... -
Page 16: W Update & Default Reset Button
a) DHCP mode => Click DHCP and then click the “Read Setting” button to get the IP address Info b) Static mode => Click Static and then key in the “IP”, “MASK”, ”GATEWAY” info. After setting IP Address, please click “Save Setting” to save IP address Info c) Save Setting =>... -
Page 17: Com Port Selection
5. SYSTEM BUTTON 1) Version: => To get the F/W version information 2) Factory Reset 3) Help => To view the steps of the firmware update 4) Firmware Update Main Board 5) Firmware Update Front Panel 6. COM PORT SELECTION Click “... -
Page 18: Connection Status
7. CONNECTION STATUS 1) Connected Status: 2) Connecting Status: 3) Disconnected Status: 8. CONNECT/DISCONECT BUTTON Click this button “ ” to change connection status 9. RS-232 BUTTON 1) Click “ ” button to switch to RS-232 function. 2) If RS-232 is connected, the button will show the sign image to let you know. 10. -
Page 19: Edid Learning
E D I D L E A R N I N G The EDID learning function is only necessary whenever you encounter any display on the HDMI output port that cannot play audio and video properly. Because the HDMI source devices and displays may have various level of capability in playing audio and video, the general principle is that the source device will output the lowest standards in audio format and video resolutions to be commonly acceptable among all HDMI displays. -
Page 20: Faq
F A Q F A Q Q: Can every TV work with the HDMI matrix? A: Basically, the answer is YES. But if your TV can not support 1080p, please refer the EDID LEARNING section to learn EDID from your TV. Q: What is EDID? Why do I need to learn EDID? A: EDID contains the whole information of the display such as the resolution and audio setting which this display can support. -
Page 21: Warranty
W A R R A N T Y The SELLER warrants the LINK HD8X8 8x8 HDMI Matrix Switcher with Full 3D Support free from defects in the material and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer.
Need help?
Do you have a question about the HD8X8 and is the answer not in the manual?
Questions and answers