1. Manuals
  2. Brands
  3. Hako Robotic Manuals
  4. Scrubber
  5. G-Force CLASSIC
  6. Parts manual and owners manual

Hako Robotic G-Force CLASSIC Parts Manual And Owners Manual

Scrubber / polisher with suction
Hide thumbs
Table of Contents

Advertisement

Quick Links

G-Force CLASSIC
SCRUBBER / POLISHER WITH SUCTION
Parts Manual and Owners Guide
Hako Australia Pty Limited
ABN 43 002 858 059
6 Pike Street, Rydalmere NSW 2116 Australia
PO Box 360 Rydalmere BC 1701
Telephone: +61 2 9684 2433 Fax: +61 2 9684 2278
Freecall within Australia: 1800 257 221
Email:
hksales@hakoaustralia.com.au
www.hakoaustralia.com.au
An ideal cleaning
solution from
Hako Rotobic.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G-Force CLASSIC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hako Robotic G-Force CLASSIC

Summary of Contents for Hako Robotic G-Force CLASSIC

  • Page 1 G-Force CLASSIC SCRUBBER / POLISHER WITH SUCTION Parts Manual and Owners Guide Hako Australia Pty Limited ABN 43 002 858 059 An ideal cleaning 6 Pike Street, Rydalmere NSW 2116 Australia solution from PO Box 360 Rydalmere BC 1701 Telephone: +61 2 9684 2433 Fax: +61 2 9684 2278 Hako Rotobic.

  • Page 2: Handle Assembly

    PACKAGING  The G-Force and G-Force Hi-Torque models Upright Handle are despatched in two cartons. The cartons contain the handle and chassis assembly. HANDLE ASSEMBLY  Remove the 5” bolt from the handle support lugs. 3” Bolt  Fit the handle between the chassis lugs. Insert 5”...

  • Page 3: Motor Controls

    PAD AND BRUSH SIZE  Use 45cm Quick Release brushes, or 45cm Quick Release pad holders with 45 cm pads. FITTING PADS AND BRUSHES  Raise the handle into an upright position and lay machine back onto the floor refer to Pic 5 ...
  • Page 4 START UP  Unwind the electrical cord and plug into power point.  Adjust handle to comfortable waist height Push Forward refer to Pic 12. FForward  Rotate wheels OFF the floor refer to Pic 12.  Check that the power indicator lamp is ON. ...
  • Page 5 SKIRT ADJUSTMENT  With the pad/brush fitted check that the Skirt Assembly is sitting evenly on the floor. Rotate the rubber Inlet Hose to be in slight compression when machine is level with the floor. This optimizes the skirt height refer to Pic 14 PLANNING THE JOB ...

  • Page 6: Power Cord Maintenance

    POWER CORD MAINTENANCE  Unplug the electrical cord from the power outlet when the machine is not in use, or when cleaning or maintaining the machine.  Wind the power cord between the handle and cord storage arm from the machine end to reduce knuckling, check for damage, and remove soilage as shown in Pic 17.
  • Page 7 HAZARD PRECAUTIONS Unplug electrical plug from the power point before conducting repair, service, maintenance or equipment cleaning. Electrical  Do not handle electrical plug or machine with wet hands and power connected.  Do not run vacuum motor when wet scrubbing or stripping. ...

  • Page 8: Specifications

    SPECIFICATIONS Main Motor Type: Induction 4 Pole CSCR Voltage and Frequency: 220 – 240 Volts a.c. / 50 – 60 Hz Power Output: 1500 watts @ 8.3 amps Vacuum Motor Type: Single stage Flo-Thru Voltage and Frequency: 220 – 240 Volts a.c. / 50 – 60 Hz Air Flow: 25 litres/sec ®...
  • Page 9 ELECTRICAL CIRCUIT DIAGRAM G-FORCE...
  • Page 10 G-FORCE Classic Chassis Assembly Parts List ITEM PART ITEM PART DESCRIPTION DESCRIPTION 13277001 Hose Inlet Assy G-Force 13220005 Cord Motor G-Force&FX Classic. 13270010 Hose Grey 32mm x 235+/-3 G-Force 13220009 Clamp 'P' Dia. 6.4 Mtg Hole 5.2 Zn Pl 13217000...
  • Page 11 CHASSIS G-FORCE CLASSIC...
  • Page 12 G-FORCE ndustrial & ommercial Handle Part Name Part No. Part Name Part No. Handle G-Force IC Assy 13277050 Bolt 5/16W x 1-1/2 Hex ZP 13210011 Handle Grip 13270005 Grommet Loom Cord 13260001 Pin M6 x 20 Dowell CP 13350010 Cord Polisher 3 Core 15m x 15A 13220007 Housing Handle Lower G-Force IC 13270001...
  • Page 13 Hako Australia Pty Ltd Warranty Policy Effective July 1, 2008 Hako Australia Made Simple Limited Warrantly Policy Hako Australia Pty Ltd warrants to the original purchaser/user that the product is free from defects in workmanship and materials under normal use. Hako Australia Pty Ltd will, oblige under this warranty to repair or replace at our factory or authorised dealer service outlet, parts that fail under normal use and service when operated and maintained in accordance with the Parts Manual and Owners Guide, after examination discloses it to have been defective.

Table of Contents