Krell Industries Duo 175 Setup Manual

AC POWER GUIDELINES Because of its powerful amplifier channels and high-capacity power supply, iBias
amplifiers will benefit from a dedicated AC circuit. Avoid connections through extension
cords or multiple AC adapters. High quality 20 amp AC strips are acceptable. Please
contact your authorized Krell dealer, distributor befor using any devices designed to alter
or stabilize the AC power.
Connecting the
Follow these steps to connect an iBias amplifier to your system.
iBias Amplifier
to Your System
1. Make sure all power sources and components are off before connecting inputs and
outputs.
Krell recommends using balanced
2. Neatly organize the wiring between the iBias amplifier and all system components.
interconnect cables. Balanced
Separate AC wires from audio cables to prevent hum or other unwanted noises from
interconnect cables not only
being introduced into the system.
can minimize sonic loss but are
3. Connect the left and right loudspeaker cables to the amplifier's left and right
also immune to induced noise,
loudspeaker output terminals (14).
especially with installations using
long cables. Balanced connections 4. Connect the left and right outputs of your preamplifier or processor to the appropriate
analog inputs (15, 16, 17) on the iBias amplifier.
have 6 dB more gain than single-
ended connections. When level
5. Plug the AC cord into the IEC connector (22) on the back panel of the iBias amplifier.
matching is critical, keep this gain
Plug the remaining end into the AC wall receptacle. Move the Power Breaker Switch
value in mind. For the Solo 375
on the rear panel to the up position. The red stand-by indicator (2) illuminates and the
or Solo 575, Krell recommends
display shows the model number, firmware version, serial number, and IP address.
the use of CAST. A Krell exclusive
Note
technology, a Krell system
Use only the power cord provided with the iBias amplifier to make the connection to AC power.
connected with Krell CAST MMF
Operation with a power cord other than the one supplied by Krell can induce noise, limit current, or
cable is the fullest expression of
otherwise impair the ability of the iBias amplifier to perform optimally.
Krell engineering.
Operating the
When powering up any system, alway turn amplifiers on last.
iBias Amplifier When powering down, always turn amplifiers off first.
1. When the amplifier is in stand-by mode, with the red stand-by indicator (2)
illuminated, turn the amplifier on by pressing the power button on the front panel
(1). There are audible clicks. The blue power indicator (2) illuminates. The display
will show the IP Address and model number and then turn off. The iBias amplifier
is now in the operational mode.
2. With the preamplifier or processor in the mute position, or the volume control fully
attenuated, select a source.
3. Start playing the source.
4. Set the volume to a comfortable listening level using the preamplifier or processor
volume control.
5. To turn the amplifier off, press the power button on the front panel (1). The red
stand-by indicator (2) illuminates.
It is now safe to turn off the rest of the system.
MODEL: iBias Power Amplifier
4 Krell iBias Amplifier Krell Industries, LLC., 45 Connair Road, Orange, CT 06477-3650 USA
TEL 203-799-9954, FAX 203-891-2028, E-MAIL contact@krellonline.com
WEB SITE www.krellonline.com
SERIAL NUMBER:
THE LEADER IN AUDIO ENGINEERING
Getting Started
Krell's history is rich with breakthrough Class A amplifiers that have helped build
the Krell legacy of offering the best sounding amplifiers available. Audiophiles have
always considered Class A technology to be the best sounding operating state for
amplifiers. However, despite Class A's unrivaled sound quality, it has fallen out
of fashion because of recent demands to reduce power consumption and heat in
home electronics products. Krell engineering took this challenge and redefined the
meaning of high performance power amplifier. Our goal – unmatched performance,
elegant design, and a compelling array of features. The breakthrough, iBias, a
patent pending circuit delivering Class A operation without the excessive heat
Overview
and wasted energy of conventional designs, housed in a striking new form factor,
with network connectivity for advanced access and monitoring. The sound is open
and unconstrained, in a manner that rivals live performance and the true sound of
voices and instruments. Music and dialogue are reproduced with a richness, detail,
and startling dynamics that fill a room.The iBias amplifier is easy to operate and
integrate into your system. The remote control accesses all amplifier functions, and
remote control connection options allow the iBias amplifier to be easily connected
with other components. The Theater Throughput feature provides easy integration of
the amplifier into a home theater system.
WARNINGS Do not place the amplifier where it could be exposed to dripping or splashing.
Do not remove or bypass the ground pin on the end of the AC cord. This may cause radio
frequency interference (RFI) to be introduced into your playback system.
This product complies with the
The ventilation slots on the top and bottom of the amplifier as well as the fan openings on the
EMC directive (89/336/EEC)
back must be unobstructed at all times during operation. Do not place flammable material on top
and the low-voltage directive
of or beneath the component.
(73/23/EEC).
Turn off all systems' power before connecting the amplifier to any component.
This CLASS 1 apparatus must
Make sure all cable terminations are of the highest quality, free from frayed ends, short circuits, or
be connected to a MAINS
cold solder joints.
socket outlet with a protective
earthing connection. THERE ARE NO USER-SERVICEABLE PARTS INSIDE ANY KRELL PRODUCT.
Unpacking
1. Open the shipping box and remove the top layer of foam. You will see these items:
1 iBias amplifier chassis
Note
1 IEC connector (AC power) cord
Save all packing materials.
1 12V Trigger cable
If you need to ship the iBias
amplifier in the future, repack
2. Carefully remove all items from the shipping box.
th unit in its original packaging
to prevent shipping damage.
3. Place the amplifier in a safe location and remove the protective plastic wrapping.
Placement Place the iBias amplifier on a firm, level surface, away from excessive heat, humidity,
or moisture. The amplifier requires at least one inch (2.54 cm) of clearance on each
side and at least two inches (5 cm) of clearance above to provide adequate ventilation.
Installations inside cabinetry may need extra ventilation.
iBias Power Amplifier
Duo 175 and Duo 300 Stereo Amplifiers
Solo 375 and Solo 575 Mono Amplifiers
Trio 300 Three Channel Amplifier
Chorus 5200 and Chorus 7200 Multi Channel Amplifiers
SETUP GUIDE
Krell iBias Amplifier 1