Subscribe to Our Youtube Channel
Related Manuals for Sabre Vision 3
Summary of Contents for Sabre Vision 3
- Page 1 VISION 3 Positive Pressure Facemask User Instructions Article No. 1074216 Issue C 10. 2004...
-
Page 2: Table Of Contents
RECORD TEST DETAILS..................9 STORAGE ......................9 SCHEDULED MAINTENANCE ..................9 MONTHLY......................9 ANNUALLY ......................9 Sabre Breathing Apparatus is a division of Scott Health and Safety Limited. Registered Office: Scott Health and Safety Limited, Pimbo Road, West Pimbo, Skelmersdale, Lancashire, WN8 9RA, United Kingdom. -
Page 3: Warnings
This manual is for use by personnel trained in the use and care of compressed air breathing apparatus, and MUST NOT be used as a self-teaching guide by untrained users. Failure to understand or adhere to the VISION 3 user instructions may result in injury or death. -
Page 4: Introduction
4 x (300 + 150) = 1800 litres/minute. There is an increased fire risk when the oxygen content is above the value shown A Sabre airline flow tester is available above. from Scott Health and Safety Limited under Article Number 1035978. -
Page 5: Training
SERVICING unauthorised alteration or repair. VISION 3 must be serviced at scheduled Evidence of purchase date will need to be intervals personnel have provided for any claims arising during the completed a formal training course and warranty period. -
Page 6: Notified Bodies
W4 4AL, to EN 137, and compressed air airline United Kingdom. breathing apparatus approved to EN 139. VISION 3 is approved to EN 136 : 1998 CL 3 and is CE marked in accordance with EEC Directive EC/686/1986. face-seal moulded non- dermatitic grey silicone. -
Page 7: Pre-Use And Monthly Checks
Bottom, Middle, Top. DO approved, to the facemask. NOT over-tighten. Note: If VISION 3 is to be used with RAS, fit filter and filter cover after first ensuring that the filter and filter O-ring are clean and in good condition. -
Page 8: Facemasks With A Net Harness
VISION 3 Hold breath for ten seconds and 3.2.2 Facemasks with a Net listen for leaks. If there are leaks, loosen Harness the head-harness and adjust the mask for a comfortable leak-tight fit and repeat test. DO NOT over-tighten the head- harness. -
Page 9: Don Apparatus
ATTACH DEMAND straps over back of head, brushing hair away from faceseal. VALVE Check that the VISION 3 head- harness is fully slackened and that the DV is connected to the facemask. Place the neck-strap round the neck. -
Page 10: All Facemasks
VISION 3 FACEMASK SEAL TEST Close the cylinder valve and keep hold of the handwheel. Hold breath for 10 seconds and listen carefully for leaks. A leak will cause the pressure gauge reading to fall. If the facemask fails the leak test:... -
Page 11: Doffing The Apparatus
Safety Limited in 1 litre and 5 litre air supply apparatus. containers under Article Numbers Clean and test VISION 3 as 2008247 and 2008248 respectively. described in Section 6. Pump dispensers are available for the above under Article Numbers 1017672 (1 litre) and 1017670 (5 litres). -
Page 12: Record Test Details
Please see Section 6.2 for details. environment away from direct heat and ANNUALLY sunlight. Storage temperature should not exceed VISION 3 must be returned for a -10°C to +40°C. workshop service annually and for a major workshop service at six-yearly intervals. - Page 13 Sabre Breathing Apparatus !"" # $% &' ( )&&)&& * + !"" # $% &' ( )&&))(...
Need help?
Do you have a question about the Vision 3 and is the answer not in the manual?
Questions and answers