EPC PM Nautic Installation Manual English MAEN971, 2009-01...
Page 2
Please read the entire installation manual prior to installing and using this equipment. Only qualified personnel may install, operate or repair this equipment. Elektronik-Systeme Lauer GmbH & Co. KG is not responsible for modified, altered or renovated equipment. Because the equipment has a wide range of applications, users must acquire the appropriate knowledge to use the equipment properly in their specific applications.
2100 Nautic * In progress ** For bridge applications Approval/Certificate Abbreviation Conformité Européene Lloyd’s Register Bureau Veritas Germanischer Lloyd Det Norske Veritas American Bureau of Shipping Russian Maritime Register of Shipping China Classification Society Korean Register of Shipping Elektronik-Systeme Lauer, MAEN971...
– The supplier neither guarantees that the EPC is suitable for your particular application, nor assumes responsibility for your product design, installation or operation. Elektronik-Systeme Lauer, MAEN971...
1.4 During Use – Keep the EPC clean. – Emergency stop and other safety functions may not be controlled from the EPC. – Do not use too much force or sharp objects when touching the keys, touch screen etc. Elektronik-Systeme Lauer, MAEN971...
1.6 Dismantling and Scrapping – The EPC or parts thereof shall be recycled according to local regulations. – The following components contain substances that might be hazardous to health and the environment: lithium battery, electrolytic capacitor and dis- play. Elektronik-Systeme Lauer, MAEN971...
Length: approximately 3.0 m. 24 V DC units are delivered without cable. Installation manual This manual describes specific information about Elektronik-Systeme Lauer products only – not about third party components. Note: Separate documentation of third party components is included on the enclosed driver software CD + as printed documentation.
Description of Parts Description of Parts 3.1 EPC PM Nautic The EPC PM Nautic consists of a Front Unit and a PC Unit. These are installed in the same way independent of the display size. Front unit PC unit Elektronik-Systeme Lauer, MAEN971...
- (brightness down) the monitor on the dimmer button Press the power button and keep it Changes video input pressed, and at the same time press + (DVI/VGA) (brightness up) on the dimmer button Elektronik-Systeme Lauer, MAEN971...
PS/2 3 x 3.5 mm USB 4 USB 2.0 mini jack Mouse ATX button USB 3 USB 2.0 Keyboard DB15HDF COM2 LAN 1 RJ-45 Power remote DB9M USB 2 USB 2.0 screw terminal USB 1 USB 2.0 Elektronik-Systeme Lauer, MAEN971...
9-11 (12 V), 10-12 (5 V) On Auxiliary power When configured as RS485, the pins are assigned at half-duplex according to be- low: Pin number Description Pin 1 RX/TX+ Pin 2 RX/TX- Pin 5 Ground Pin 9 (optional) +5 V (auxiliary power supply) Elektronik-Systeme Lauer, MAEN971...
The quality of the memory module may influence the system stability. When updating the memory module, or adding a second one, please only use memory modules cleared by Elektronik-Systeme Lauer. Memory modules are electrostatic sensitive components. Relevant protective measures (earth) have to be considered during as- sembly/disassembly.
The EPC PM Nautic is certified for the connection to protective grounded power supply according to EN60950. The controlling transformer has to com- ply with EN60742. Note: Check the power supply system with the relevant data on the type plate. Elektronik-Systeme Lauer, MAEN971...
A manual actuation of the ATX power switch, i.e. to start the BIOS menu au- tomatically to check and confirm correct settings, can be necessary if the system registers an error during shut-down or booting. This is not a malfunction but a safety feature. Elektronik-Systeme Lauer, MAEN971...
“D:” is a complete free partition which for example can be used for your data (beneficial for example for data back-up). Drive “E:” contains all data required for a new installation (drivers and operation system). This partition always uses a FAT 16 data system. Elektronik-Systeme Lauer, MAEN971...
4: 1280x1024 48(bit) 21" 10: 1600x1200 48(bit) Integrated Peripherals/ PWRON After PWR-Fail Super IO Device Integrated Peripherals/ Serial Port 3 Use IRQ IRQ4 Super IO Device Integrated Peripherals/ Serial Port 4 Use IRQ IRQ3 Super IO Device Elektronik-Systeme Lauer, MAEN971...
After operating the system for the first time we recommend that you make start discs (emergency discs). These might be required to restore an operational system. Additionally, we recommend making backup copies of your own data and applica- tions. Elektronik-Systeme Lauer, MAEN971...
Technical data: (check the BIOS settings when re-installing) – Serial Tsharc 12 Touch-Controller – Com 3 (check the BIOS settings) – 3E8 hex – IRQ 4 – 9600 bps Perform the SETUP.EXE under: – E:\Driver\Driver-EPC-PM\Touch\Touch – CD-ROM: (D:) E:\EPC-PM\Touch Elektronik-Systeme Lauer, MAEN971...
Page 21
Operation 1. Follow the instructions on the screen and press Continue. 2. Accept the license provisions. Elektronik-Systeme Lauer, MAEN971...
Page 22
Operation 3. Select Autodetect or manually select the technical connection data. Elektronik-Systeme Lauer, MAEN971...
Page 23
4. Press Finish and follow the instructions for a re-start. 5. After a re-start of the operating system you will find Hampshire Control Panel among the programs. 6. Calibrate the touch screen with your finger or with a rounded pointed touch pen. Elektronik-Systeme Lauer, MAEN971...
The grafic driver will be installed twice. 2. After finishing the installation and re-starting the EPC PM Nautic the fol- lowing entries are available under the Display icon in the Control Panel, or in the display properties. Elektronik-Systeme Lauer, MAEN971...
– Via the MS-DOS window, under Start/All Programs/Accessories/ Command prompt, you can set a “connection PING” to test your connec- tions to the server and other PC’s. (for example: C:\ping 192.168.5.100). Elektronik-Systeme Lauer, MAEN971...
Inside the appliance there are electronic components which can be destroyed by electrostatic charges. Therefore cautionary measures have to be taken from the moment the appliance is opened. These can be found in the guidelines for electro- static endangered components (EGB-guidelines). Elektronik-Systeme Lauer, MAEN971...
1. To change the fan you have to remove the left hand part of the rear enclo- sure. To open the enclosure, remove the six (6) marked screws with an Allen key. 2. Lift the enclosure and pull out the fan cable, according to the picture below. Elektronik-Systeme Lauer, MAEN971...
Page 29
Unplug and remove the fan. 4. Remove the protective cover of the fan and remove the fan with a Phillips head screw driver. 5. After changing the fan, assemble the appliance in the reverse order. Elektronik-Systeme Lauer, MAEN971...
To install a PCI-board the right hand side part of the rear enclosure has to be removed. 1. To open the enclosure remove the marked seven screws with an Allen key. After removing the screws the enclosure can be easily removed. Elektronik-Systeme Lauer, MAEN971...
Page 31
The picture of the opened appliance below shows the board holder (1) and the 2 PCI-slots (2). 2. Remove the cover of the desired slot to insert your PCI-board, by removing the screw and pulling out the cover. Elektronik-Systeme Lauer, MAEN971...
Page 32
4. Insert the PCI-board, if necessary bend the slot bracket a little bit. Please ensure a correct fit at the rear edge (3) of the slot and make sure the metal bracket goes into the groove (4). Elektronik-Systeme Lauer, MAEN971...
Page 33
Service 5. Mount your PCI-board and make sure to properly tighten the screw. 6. Re-assemble the board holder and tighten the two screws properly. Elektronik-Systeme Lauer, MAEN971...
Page 34
This way the support can be used in the correct way. Note: If two wide boards are used, the short support (5) can be removed. Elektronik-Systeme Lauer, MAEN971...
1. To change or expand the memory card you have to remove the left hand part of the rear enclosure. To open the enclosure, remove the six (6) marked screws with an Allen key. 2. Lift the enclosure and pull out the fan cable, according to the picture below. Elektronik-Systeme Lauer, MAEN971...
Page 36
4. The picture above shows one free (3) and one occupied slot. If a memory expansion is carried out the memory module is positioned vertically and pushed into the slot, the fixing brackets (4) shall snap shut. Elektronik-Systeme Lauer, MAEN971...
Page 37
6. To mount a new memory board, center it into the slot, and push it firmly but gently down until the holding brackets snap shut. 7. Bend back and plug in the ribbon cable. 8. Subsequently plug in the fan cable and reposition the enclosure. 9. Re-fix the enclosure. Elektronik-Systeme Lauer, MAEN971...
Page 38
Service Elektronik-Systeme Lauer, MAEN971...
5 x USB (4 x USB on rear side, 1 x USB on front side) 2.0 480 Mbps Extension slots 2 x PCI up to 220 mm length Compact Flash 1 x internal (optional) and 1 x external (Compact flash, type II) ports Keyboard/mouse 2 x PS/2 For external monitor Elektronik-Systeme Lauer, MAEN971...
Page 40
4096 x 4096 points* resolution Ambient 0 ° to +55 °C temperature Relative ambient 30% to 90% non-condensed humidity Storage -20 ° to +70 °C temperature Relative storage 10% to 90% non-condensed humidity * Only applies to EPC PM 1500t/1700t/1900t/2100t Elektronik-Systeme Lauer, MAEN971...
Drawings Drawings 7.1 EPC PM 1500t/1500 Nautic Front View R5.0 Brightness Up 1x USB waterproof Power On-Off Brightness Down Elektronik-Systeme Lauer, MAEN971...
Drawing Cut out dimensions: 369.0 x 324.0 mm. max. thickness 5.0 mm 6 x boreholes Ø 6.5 Mounting method: 6 x M6x25 V2A-screws DIN 6912. Screws and o-ring seals are included. Max. 5 mm thick mounting frame. Elektronik-Systeme Lauer, MAEN971...
Drawings 7.4 EPC PM 1700t/1700 Nautic Front View 430±0.1 414±0.1 200±0.1 R10.0 1 x USB waterproof Power On-Off Brightness Up Brightness Down Elektronik-Systeme Lauer, MAEN971...
Cut out dimensions: 396.0 x 364.0 mm. max. thickness 5.0 mm 8 x boreholes Ø 6.5 200±0.2 414±0.2 Mounting method: 8 x M6x25 V2A-screws DIN 6912. Screws and o-ring seals are included. Max. 5 mm thick mounting frame. Elektronik-Systeme Lauer, MAEN971...
Drawings 7.7 EPC PM 1900t/1900 Nautic Front View 483.2±0.1 465.2±0.1 230±0.1 8 x boreholes Ø 6.5 R10.0 1 x USB waterproof Power On-Off Brightness Up Brightness Down Elektronik-Systeme Lauer, MAEN971...
Cut out dimensions: 438 x 416 mm. max.thickness 5.0 mm 8 x boreholes Ø 6.5 230±0.2 465.2±0.2 Mounting method: 8 x M6x25 V2A-screws DIN 6912. Screws and o-ring seals are included. Max. 5 mm thick mounting frame. Elektronik-Systeme Lauer, MAEN971...
Drawings 7.10 EPC PM 2100t/2100 Nautic Front View ±0.1 ±0.1 ±0.1 8 x boreholes Ø 6.5 R10.0 1 x USB waterproof Power On-Off Brightness Up Brightness Down Elektronik-Systeme Lauer, MAEN971...
Cut out dimensions: 500 x 443 mm. max. thickness 5.0 mm 8 x boreholes Ø 6.5 ±0.2 ±0.2 Mounting method: 8 x M6x25 V2A-screws DIN 6912. Screws and o-ring seals are included. Max. 5 mm thick mounting frame. Elektronik-Systeme Lauer, MAEN971...