Subscribe to Our Youtube Channel
Related Manuals for VideoComm Technologies EWC-003 (MXR-5838c )
Summary of Contents for VideoComm Technologies EWC-003 (MXR-5838c )
- Page 1 MXR-5838 Series Manual Rev. B 2007 # EWC-003 (MXR-5838c ) # MX-5838c 5.8GHz Wireless Camera It’s About Real-Time OWNER’S MANUAL...
-
Page 2: Table Of Contents
II. In order to comply with the FCC/IC adopted RF exposure requirements, this transmission system will be installed by an authorized professional installer of VideoComm Technologies. Installation of all antennas must be performed in a manner that will provide at least 23cm clearance from the front radiating aperture, to any user or member of the public. -
Page 3: Introduction
MXR-5838 Series Manual Rev. B 2007 INTRODUCTION Introduction VideoComm introduces a real-time wireless camera solution that is not susceptible to interference from 2.4GHz 802.11 b/g data devices. Featuring 4 user selectable channels, this wireless camera system is an ideal choice when multiple wireless video links are required for any portable, temporary or covert surveillance and monitoring application. -
Page 4: Parts List
Please inspect the packaging carefully to ensure you have received all the necessary parts and accessories listed. Refer to the following chart to determine which parts are included with your product. If any parts are missing or damaged, contact VideoComm Technologies, Customer Service or your re-seller immediately. -
Page 5: System Setup
MXR-5838 Series Manual Rev. B 2007 SYSTEM SETUP Channel Selection Camera For the wireless link to work, both devices must have the same channel selected. 1. Power-UP the Camera using the included power supply & switch to “ON” 2. Set the desired channel by moving the slide switch 3. -
Page 6: Connections
MXR-5838 Series Manual Rev. B 2007 Connections Power Supply Connect RCA Cable Connect directly to camera for secondary hardwired video output Channel Select Power ON-OFF Switch Switch... -
Page 7: Camera Mounting Options
MXR-5838 Series Manual Rev. B 2007 Camera Mounting Options Wall OR Ceiling Mount Surface Mount... -
Page 8: Channel Selection Receiver
5. The receiver must be set to the same channel as the camera. 6. We strongly recommend that you do not adjust the video gain adjustment without first consulting a member of the VideoComm Technologies Tech Support Team. Receiver Channels Channel # 1 5.733 GHz... -
Page 9: Conducting A Bench Test
• Compare the unit to the product photo on the attached specification sheet. • Check for physical damage to the devices, contact your distributor or VideoComm Technologies Technical Support immediately should you suspect damage to the unit. • Ensure all parts are included. -
Page 10: Tips & Trouble Shooting
MXR-5838 Series Manual Rev. B 2007 TIPS & TROUBLE SHOOTING Things that block transmission Things that block transmission are not always obvious. Consider any obstruction that may get in the way or reduce the wireless signal strength along the way. Here are some of the most common pitfalls: •... -
Page 11: Specifications
MXR-5838 Series Manual Rev. B 2007 SPECIFICATIONS Camera Operating Frequency 5.725GHz – 5.875GHz, 4 User Selectable Channels Receiver Operating Frequency 5.725GHz – 5.875GHz, 8 User Selectable Channels Radiated Power 50mV/m @ 3m Range (Line-of-Sight) Up to 1,000 feet Line-of-Sight / 300 feet indoors Transmitter Antenna Type 3dB Fixed Directional Receiver Antenna Type... -
Page 12: Warranty Information/ Terms & Conditions
MXR-5838 Series Manual Rev. B 2007 WARRANTY INFORMATION/ TERMS & CONDITIONS VideoComm Technologies, herein referred to as “VCT.” LIMITED WARRANTY VCT hereby warrants, subject to the conditions here in below, that should this product become defective by reason of improper workmanship or material defect during the specified warranty period, VCT will repair the same, effecting all necessary parts without charge for either parts or labor, or replace the unit at VCT option.
Need help?
Do you have a question about the EWC-003 (MXR-5838c ) and is the answer not in the manual?
Questions and answers