CallerID Whozz Calling? 4 POS Caller ID Technical Manual

CallerID Whozz Calling? 4 POS Caller ID Technical Manual

Pos series

Advertisement

Whozz Calling?
POS Caller ID
Interface Unit
WHOZZ
CALLING?
WHOZZ
CALLING?
Technical Manual
Whozz Calling? POS Series
4 and 8 Line Units
[Belcore 202 (USA) & DTMF Signaling Version]
4
8
for
POS Caller ID
POS Caller ID
Caller
ID
ID
.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Whozz Calling? 4 POS Caller ID and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for CallerID Whozz Calling? 4 POS Caller ID

  • Page 1 Whozz Calling? WHOZZ POS Caller ID CALLING? POS Caller ID Interface Unit WHOZZ POS Caller ID CALLING? Technical Manual Whozz Calling? POS Series 4 and 8 Line Units [Belcore 202 (USA) & DTMF Signaling Version] Caller .com...
  • Page 2: Quick Start Procedure

    * The power up sequence of the unit will flash the LEDs and a couple of seconds. The unit will send the firmware version number of each channel to the serial port when the DIP switches are positioned to send the CallerID.com format...
  • Page 3 (Off -FSK, On -DTMF) #5 Baud rate (Off -9600, On -1200) #5 Baud rate (Off -9600, On -1200) #7 Output Format (Off -CallerID.com, On-TCI) #7 Output Format (Off -CallerID.com, On-TCI) #8 Unit model (Off -8 line, On -4 line) #8 Unit model (Off -8 line, On -4 line)
  • Page 4: Dip Switch Settings

    9600 1200 OUTPUT FORMAT The unit can deliver either the CallerID.com Whozz Calling? format or the alternative TCI format. DIP switch number 7 control the unit output format. Refer to the table below and to Fig. 2a & 2b. Format CallerID.com...
  • Page 5 Fig. 2a CallerID.com Format Fig. 2a CallerID.com Format (DIP Switch #7 set OFF) (DIP Switch #7 set OFF) Phone number field - 14 characters. Inbound/Outbound Checksum Date Field Some areas in Canada deliver only 7 digits. & Start/End of call...
  • Page 6: Connecting To A Computer

    The CallerID.com format is recommended since it is the industry standard. This format is used with all other CallerID.com products with serial output. Several software vendors have adopted this standard since it gives them the flexibility to handle any type of call accounting application. The CallerID.com format provides additional fields for outbound digits dialed, inbound digits dialed after answer, number of rings before answer, call duration, and type of distinctive ring pattern.
  • Page 7: Connecting To Phone Lines

    The unit should be connected to the serial port, placed in a convenient location next to the computer, and your software installed. Permanent installation and phone line connections can be made once communications between the software and hardware is established. Plug in the power to the unit and run the software. Phone lines need not be connected at this time.
  • Page 8 Fig. 3 Telephone Connections 8 Outside Lines (modular or solid wire) to a telephone system switch or directly to desktop phones Lines Telephone from Switch Out to Tel. Desktop (if present) Phones (RJ21x Solid wire to Block) Modular Adapters (if needed) 8 Modular, single pair, phone cords to unit L1 L2...
  • Page 9: Specifications

    CallerID.com repair facility; or damage attributed to an act of God. Lightning is considered an act of God. CallerID.com makes no other warranty, either expressed or implied, with respect to this product. If a problem develops concerning this product, contact CallerID.com directly for a Return Material Authorization (RMA).
  • Page 10 Appendix - RS232 Pin Outs When the serial port is configured to “No Flow Control,” only Transmit and Ground connections are required. Pin 7 and Pin 8 need to be connected only if other serial flow control types are selected. Computer DB9/M Serial Port Monitoring Unit DB9/F Pin 1 (Carrier Detect)
  • Page 11 Caller .com 3107-D Medlock Bridge Road, Norcross, GA 30071 800.240.4637 770.263.7111...

This manual is also suitable for:

Whozz calling? 8 pos caller id

Table of Contents