Related Manuals for Longshine LCS-WRM-3214
Summary of Contents for Longshine LCS-WRM-3214
- Page 1 Model No. LCS-WRM-3214 ADSL2/2+ 4 Port Wireless Router For Annex A/B Version 1.0 May.2006...
-
Page 2: Table Of Contents
Table of Contents Specification ....................... 4 Package Contents ...................... 6 Hardware Connecting....................7 LED Indicators ......................7 General Setting......................8 Advanced Setup ....................... 12 Setup ......................... 12 LAN Setup....................12 LAN Configuration ..................12 Ethernet Switch ..................14 WAN Setup....................15 Two Step PVC .................... - Page 3 IGMP Proxy ....................44 Static Routing ..................... 45 Dynamic Routing ..................46 Policy Routing .................... 48 Ingress ....................... 50 Egress ......................51 Shaper......................52 Web Access Control ................... 53 Web Access Control ................... 53 SSH Access Control ................... 54 WIRELESS......................55 Setup......................
- Page 4 RIP Help ..................... 80 QoS Help....................80 Troubleshooting ....................81 Appendix ......................88...
-
Page 5: Specification
Specification Line Connection RJ-11(2 wires) , RJ-45 (4 port) DMT modulation and demodulation Tone detection for low power mode ITU 992.1 (G.dmt) Annex A, B ADSL Features ITU 992.2 (G.lite) ITU 992.3 ADSL2 (G.dmt.bis) ITU 992.5 ADSL2+ ANSI T1.413 Issue 2 Maximum downstream rate of 24 Mbps (ADSL2+) Full-rate adaptive modem Maximum upstream rate of 1 Mbps... - Page 6 connection,DMZ function can be set up between them Complies with IEEE 802.3u specification Supports Auto-Negotiation Supports Auto-MDIX, Auto-MDI Supports IEEE 802.3x Flow control in Full Duplex mode Certification CE,LVD WIN 98SE ; WIN 2000；WIN ME；WIN XP System Requirement PII-266 + 32M RAM External AC Power Power ON/OFF switch (option) Power...
-
Page 7: Package Contents
Package Contents Longshine ADSL 2/2+ Wireless 4 Port Router CD-ROM containing Manual, Quick start Guide Ethernet Cable (CAT5 UTP Straight-Through) Telephone Cable (RJ11) Power Adapter (12VAC 800mA) Quick Installation Guide Splitter (Optional) -
Page 8: Hardware Connecting
Hardware Connecting Connect to Power Phone cable connect Adapter to Splitter Factory reset button RJ-45 connect to computer Ethernet Port Phone Cable connect to wall phone jack LED Indicators The LED Indicators are located on the front of the unit, they are green in color. The meanings are as follows: Label Meaning... -
Page 9: General Setting
General Setting 1. Move your cursor as flowing sequence Start \ Settings \ Control Panel and click Control Panel. Then double-click on the Network Connections Double Click on this icon 2. In the LAN or High-Speed Internet window, right-click on icon corresponding to your network interface card (NIC) and select Properties.(This icon may be labeled Local Area Connection). - Page 10 3. In the General Tab of the Local Area Connection Properties menu. Highlight Internet Protocol (TCP/IP) under “This connection uses the following items.” by click on it once. Click on the Properties button. 4. Select Obtain an IP Address automatically: by clicking once in the circle. Click OK button to confirm and save your changes, and the close the Control Panel.
- Page 11 5. Release IP & Renew IP, then Check Default Gateway: 192.168.1.1. 6. Launch your PC web browser and enter the URL: http://192.168.1.1 7. Please enter the user name and password as below: User name: Admin Password: Admin, And then, click “Log In”.
- Page 12 8. After Login procedure the Quick Start Page will appear. Select country from the drop-down list. Select ISP from the drop-down list. Select Encapsulation from the drop-down list. The VPI and VCI value will automatically set up ok. Then click Next. If you can’t find your ISP setting, please click Config.
-
Page 13: Advanced Setup
Advanced Setup Setup The Setup section allows you to create new connections, edit existing connections, and configure other basic settings. LAN Setup LAN Configuration The following is displayed LAN Setup. Select Configure... - Page 14 IP Address: Private IP address for connecting to a local private network (Default: 192.168.1.1). Netmask: Netmask for the local private network (Default: 255.255.255.0). Default Gateway: This field is optional. Enter in the IP address of the router on your network. Host Name: Required by some ISPs.
-
Page 15: Ethernet Switch
Ethernet Switch This Ethernet Switch Configuration page allows you to set value for data transfer; Physical Port: There are five kinds of mode for data transfer (Auto)(10/Half Duplex)(10/Full Duplex)(100/Half Duplex)(100/Full Duplex). Click Apply to complete the setup. Click Save All to save the changes. -
Page 16: Wan Setup
WAN Setup Two Step PVC The Two-step PVC page is added to support the Remote Management /Clear Embedded Operations Channel (EOC) feature, which is a China MII requirement. This page allows WAN connections to be created in two steps: 1. Create multiple PVCs with VPI; VCI values, and encapsulation types. The following encapsulation methods are supported: PPPoA PPPoE... -
Page 17: New Connection
New Connection When working with wide area connections, the first thing you must do is to have the handle of the connection. Once you have the handle for a Connection you must define the PVC and protocol settings for it. Name: Enter the name of your ISP. - Page 18 Enforce MTU: This feature is enabled by default. It forces all TCP traffic to conform with PPP MTU by changing TCP maximum segment size to PPP MTU. If it is disabled, you may have issues accessing some Internet sites. Debug: Enables PPPoE connection debugging facilities. This option is used by ISP technical support and ODM/OEM testers to simulate packets going through the network from the WAN side.
- Page 19 and is configurable. The Auto-Sensing PVC feature itself is also configurable in that the auto-search mechanism can be disabled. Upon DSL synchronization, end-to-end OAM pings will be conducted for every defined PVCs. The result of the pings will be recorded in an array for later use to determine the usability of the particular PVC for connectivity.
-
Page 20: Pppoe Settings
PPPoE Settings At the Setup main page, click New Connection. At the Type field select PPPoE. In the Name field, enter a unique name for the PPPoE connection. The name must not have spaces and cannot begin with numbers. The Network Address Translation (NAT) and the Firewall options are enabled by default. - Page 21 the DSLAMS and Routers on the ISP to handle VLAN Tags. Extended support is also available, which allows multiple connections to be placed over the single PVC without VLAN support (VLAN Tag of 0 is this special case). In this mode of operation, a received packet is flooded on all the connections that reside over it.
-
Page 22: Pppoa Settings
PPPoA Settings At the Setup main page, click New Connection. At the Type field select PPPoA. Enter a unique name for the PPPoA connection in the Name field. The name must not have spaces and cannot begin with numbers. The Network Address Translation (NAT) and the Firewall options are enabled by default. - Page 23 support is also available, which allows multiple connections to be placed over the single PVC without VLAN support (VLAN Tag of 0 is this special case). In this mode of operation, a received packet is flooded on all the connections that reside over it. Priority Priority is given to a VLAN connection from 0-7.
-
Page 24: Static Settings
Static Settings At the Setup main page, click New Connection. At the Type field select Static. In the Name field, enter a unique name for the Static connection. The name must not have spaces and cannot begin with numbers. The Network Address Translation (NAT) and the Firewall options are enabled by default. -
Page 25: Dhcp Settings
DHCP Settings At the Setup main page, click New Connection. At the Type field select DHCP. Enter a unique name for the DHCP connection in the Name field. The name must not have spaces and cannot begin with numbers. The Network Address Translation (NAT) and the Firewall options are enabled by default. -
Page 26: Bridge Settings
Bridge Settings At the Setup main page, click New Connection. At the Type field select Bridge. Enter a unique name for the Bridged connection in the Name field. The name must not have spaces and cannot begin with numbers. In the Bridge Settings section, select the Encapsulation Type (LLC or VC). Note—... -
Page 27: Clip Settings
CLIP Settings At the Setup main page, click New Connection. At the Type field select CLIP. Enter a unique name for the static connection in the Name field. The name must not have spaces and cannot begin with numbers. The Network Address Translation (NAT) and the Firewall options are enabled by default. -
Page 28: Modem
Modem This page allows you Select ADSL Transmission Type. MULTI_MODE: Support Multi-Mode standard (ANSI T1.413 Issue 2; G.dmt(G.992.1); G.lite(G.992.2)). ADSL_ANSI_T1.413: Full-Rate (ANSI T1.413 Issue 2) with line rate support of up to 8 Mbps downstream and 832 Kbps upstream. ADSL_G.dmt: Full-Rate (G.dmt, G992.1) with line rate support of up to 8 Mbps downstream and 832 Kbps upstream. -
Page 29: Advanced
ADVANCED UPnP Universal plug and play (UPnP), NAT, and firewall traversal allow traffic to pass through the RG for applications using the UPnP protocol. This feature requires one active WAN connection. In addition, the PC should support this feature. In the presence of multiple WAN connections, select a connection on which the incoming traffic is present, for example, the default WAN connection. -
Page 30: Sntp
SNTP The Router keeps time by connecting to a Simple Network Time Protocol (SNTP) server. This allows the Router to synchronize the system clock to the global Internet. The synchronized clock in the Router is used to record the security log and control client filtering. -
Page 31: Snmp
SNMP The Simple Network Management Protocol (SNMP) let a network administrator monitor on a network by retrieving settings on remote network devices. Network administrator typically runs an SNMP management station program such as MIB browser on a local host to obtain information from an SNMP agent such as the router you use now. - Page 32 TR-069 TR-069 is CPE Management Protocol from WAN side, intended for communication between a CPE and Auto-Configuration Server (ACS). The CPE WAN Management Protocol defines a mechanism that encompasses secure auto-configuration of a CPE, and also incorporates other CPE management functions into a common framework. The CPE WAN Management Protocol is intended to support a variety of functionalities to manage a collection of CPE, including the following primary capabilities: •Auto-configuration and dynamic service provisioning...
-
Page 33: Port Forwarding
Port Forwarding The port forwarding feature allows you to direct incoming traffic to specific LAN hosts based on a protocol port number and protocol. Using the Port Forwarding page, you can provide local services (for example, web hosting) for people on the Internet or play Internet games. -
Page 34: Dmz
This DMZ Settings page allows you Enable or Disable this function. This function is disabled by default. By enabling DMZ, you add an extra layer of security protection for hosts behind the firewall. Enable DMZ Function. Enable DMZ: Enables/disables the Demilitarized Zone feature. This field is unchecked (disabled) by default. -
Page 35: Custom Port Forwarding
Custom Port Forwarding The Custom Port Forwarding page allows you to create up to 15 custom port forwarding entries to support specific services or applications, such as concurrent NAT/NAPT operation. Connection: Select the WAN connection on which the Custom Port Forwarding rule is to be applied. -
Page 36: Ip Filter
IP Filter The IP filtering feature allows you to block specific applications/services based on the IP address of a LAN device. You can use the IP Filters page to block specific traffic (for example, block web access) or any traffic from a host on your local network. A database of predefined IP filters allows you to apply one or more filtering rules to one or more members of a defined LAN group. - Page 37 • TCP • UDP • TCP and UDP • ICMP • Any Filter Name: Name of the IP filter rule you are creating. Enable: The Enable button is checked by default, meaning this rule is automatically applied when you click Apply. Source IP: The LAN-side source IP address assigned to outgoing traffic on which filtering is applied.
-
Page 38: Lan Clients
LAN Clients The LAN clients feature allows you to see all the hosts on the LAN segment. Each host is qualified to be either dynamic (host obtained a lease from this RG) or static (host has a manually-configured IP address). Select LAN Connection: Select the LAN connection to which the client is to be added. -
Page 39: Lan Isolation
LAN Isolation The LAN Isolation page allows you to block traffic from one LAN group to another LAN group. Click Apply to complete the setup. Click Save All to save the changes. -
Page 40: Tr-068 Wan Access
TR-068 WAN Access The TR-068 WAN Access page enables you to give temporary permission to someone (such as technical support staff) to be able to access your RG from the WAN side. From the moment the account is enabled, the user is expected to log in within 20 active minutes, otherwise the account expires. -
Page 41: Bridge Filters
Bridge Filters The bridge filtering mechanism provides a way for you to define rules to allow or deny frames through the bridge based on source MAC address, destination MAC address, frame type, and physical ports. When bridge filtering is enabled, each frame is examined against every defined filter rule in sequence. - Page 42 Dest MAC: The destination MAC address. Dest Port: Destination port. You can choose from Any, Ethernet, USB, and WLAN. Protocol: You can choose from the following options: PPPoE Session, PPPoE Discovery, IPX - Ethernet II, RARP, IPv6, IPv4, and Any. Mode: There are two filtering modes: Deny and Allow.
-
Page 43: Web Filters
Web Filters The Web Filters page allows you to manage the type of web content that passes through your RG. Click Apply to complete the setup. Click Save All to save the changes. -
Page 44: Dynamic Dns Client
Dynamic DNS Client The Dynamic DNS Client page allows you to enable/disable the Dynamic DNS feature. Connection: This field defaults to your RG’s WAN connection over which your RG will be accessed. DDNS Server: This is where you select the server from different DDNS service providers. -
Page 45: Igmp Proxy
IGMP Proxy The IGMP Proxy page allows you to enable multicast on available WAN and LAN connections. You can configure the WAN or LAN interface as one of the following: Upstream: The interface that IGMP requests from hosts is sent to the multicast router. Downstream: The interface data from the multicast router are sent to hosts in the multicast group database. -
Page 46: Static Routing
Static Routing The Static Routing page enables you to define routes for specific subnets on the WAN/LAN side. The RG allows you to manually program the RG's routing table. Up to 16 static routes can be added. Choose a Connection: Select the LAN group or WAN connection to which a static routing subnet is to be applied. -
Page 47: Dynamic Routing
Dynamic Routing The dynamic routing feature enables the RG to dynamically define routes for WAN and LAN subnets. Dynamic routing uses routing information protocol (RIP) for exchanging routing information with other routers in the network. It is supported across both WAN and LAN interfaces. Any RIP-enabled router sends out automatic update packets containing its own routing table on a periodic basis (every 30 secs). - Page 48 This feature allows you to control how and which routes get distributed through the network. For example, by selecting In only mode, routes to private LAN networks are prevented from being sent over to the WAN-side router. The following four direction options are available: •...
-
Page 49: Policy Routing
Policy Routing The Policy Routing Configuration page is accessed by selecting Policy Routing on the Advance home page. This page enables you to configure policy routing and QoS. Ingress Interface: The incoming traffic interface for a Policy Routing rule. Selections include LAN interfaces, WAN interfaces, locally generated (traffic), and not applicable. - Page 50 entering the protocol first. Destination Port: The destination protocol port or port range. You cannot configure this field without entering the protocol first. Source MAC: The MAC address of the traffic source. Local Routing Mark: This field is enabled only when Locally Generated is selected in the Ingress Interface field.
-
Page 51: Ingress
Ingress The Ingress page enables you to configure QoS for packets as soon as they come into the RG. This page is accessed by selecting Ingress on the Advance main page. Interface: For both WAN and LAN interfaces, you can configure QoS for layer 3 (IP) data traffic. -
Page 52: Egress
Egress The default Egress page setting for all interfaces is No Egress. In this mode, the domain mappings of the packets are untouched. -
Page 53: Shaper
Shaper The Shaper Configuration page is accessed by selecting Shaper on the Advance main page. Interface: The selections are WAN/LAN interfaces except WLAN, which does not support Shaper feature. This field needs to be selected before shaper configuration. Max Rate: This field is applicable for the HTB Queue Discipline and Low Latency Queue Discipline;... -
Page 54: Web Access Control
Web Access Control The Web Access Control page allows you to access the RG remotely via the web from the WAN side. Enable: Enables/disables the remote web access feature. Choose a Connection: Select the WAN connect over which the remote web access feature is enabled. -
Page 55: Ssh Access Control
SSH Access Control The SSH Access Control page allows you to access the RG remotely via SSH from the WAN side. Enable: Enables/disables the remote web access feature. Choose a Connection: Select the WAN connect over which the remote web access feature is enabled. -
Page 56: Wireless
WIRELESS Setup This page allow you to enable and disable the wireless LAN function, create a SSID, and select the channel for wireless communications.. Primary SSID: Type an SSID in the text box. The SSID of any wireless device must match the SSID typed here in order for the wireless device to access the LAN and WAN via the router Hidden SSID: Enables/disables the hidden SSID feature. -
Page 57: Configuration
Configuration This Wireless Configuration page shows the Wireless Function Status. Beacon Period: Type the Beacon Period in the text box. You can specify a value from 0 to 65535. The default Beacon Period is 200. DTIM Period: Type a DTIM (Delivery Traffic Indication Message) Period in the text box. -
Page 58: Multiple Ssid
Multiple SSID You can access the Multiple SSID page by clicking the Multiple SSID link. The Enable SSID field allows you to create multiple SSIDs for the Wireless Router. Enable Multiple SSID: Enables/disables multiple SSID. Secondary SSID: The secondary SSID of the Wireless Router is up to 32 characters and is unique from the primary SSID. -
Page 59: Security
Security Select a Wireless Security level None: Disable Wireless encryption. WEP: WEP encryption scrambles the data transmitted between the wireless stations and the access points to keep network communications private. It encrypts uni-cast and multicast communications in a network. Both the wireless stations and the access points must use the same WEP key for data encryption and decryption. -
Page 60: Management
Management The Wireless Management page allows your prestige can check the MAC addresses of Wireless stations against a list of allowed or denied MAC addresses. MAC Address: Enter the MAC Address. (Format: 00-0e-2e-41-23-4e). Access List can accept 64 groups. Enable Access List: Enable the Wireless Management by Access List. Click Apply to complete the setup. -
Page 61: Wds
Wireless distribution system (WDS) is a system that interconnects BSS to build a premise wide network. WDS network allows users of mobile equipment to roam and stay connected to the available network resources. You can configure your Wireless Router as WDS mode using the WDS page. WDS Mode: Bridge: In Bridge mode, the Wireless Router basic service set (BSS) service is enabled. - Page 62 hierarchy. This uplink cannot be configured if Root is enabled. Downlink Connection Check Boxes: The BSS ID of the lower device in the WDS hierarchy connected to this Wireless Router. Up to four downlinks can be configured. Click Apply to complete the setup. Click Save All to save the changes. How to setting up the WDS with NSP? Reference doc: AP-DK_6_3_AN_WDS_v1_0.pdf and Environment:...
- Page 63 2. Please check your AR7WRD’s MAC address at web Example: 3. Please check your AP at the same channel, make sure AP-A and AP-B at the same channel, Example: 4. Click the wireless at top bar and click the WDS at left bar and you will see the screen as following.
- Page 64 5. Select the WDS mode to Crude mode. Example: 6. Fill in the up-link blanks with AP-B’s MAC address at AP-A’s WDS web screen as following. Example: 7. Fill in the down-link blanks with AP-A’s MAC address at AP-B’s WDS web screen...
- Page 65 as following. Example: 8. Click on the TOOLS at top bar and select the System Commands at left bar and then click on the SAVE ALL and Restart. 9. You can ping the PC each other.
-
Page 66: Tools
TOOLS The Tools section allows you to save the configuration, restart the gateway, update the gateway firmware, setup user and remote log information and run Ping and Modem tests. System Commands System Commands allow you to carry out basic system actions, Press the button to execute a command. -
Page 67: Remote Log
Remote Log The Router Table page displays routing table and allows the user to manually enter the routing entry. The routing table will display the routing status of Destination, Netmask, Gateway and Interface. The interface br0 means the USB interface; Io0 means the loopback interface and ppp1 means the PPP interface. -
Page 68: User Management
User Management User Management is used to change your User Name or Password. User Name: Default is ‘Admin’. You can enter your new user name here. Password: Default is ‘Admin’. You can enter your new password here. Confirmed Password: Enter your new password here again to confirmed. Idle Timeout: The default is 30minutes. -
Page 69: Update Gateway
Update Gateway To update your gateway firmware, choose an update image (Kernel/ File system) or configuration file In Select a File, and then click the Update Gateway button. Additionally, you may download your configuration file from the system by clicking Get Configuration. -
Page 70: Ping Test
Ping Test Packet INternet Groper is protocol that sends out ICMP echo requests to test whether or not a remote host is reachable. -
Page 71: Modem Test
Modem Test The Modem Test page is used to check the connectivity to the WAN. This test may take a few seconds to complete. Before running this test, make sure you have at least one WAN connection configured and have a valid DSL link. If the DSL link is not connected, the test will fail. -
Page 72: Status
STATUS The Status section allows you to view the Status/Statistics of different connections and interfaces. Network Statistics The Ethernet Network Statistics page shows the statistics for the Ethernet connection. The DSL Network Statistics page shows the statistics for the DSL connection. The Wireless Network Statistics page shows the statistics for the Wireless connection. -
Page 74: Connection Status
Connection Status The Connection Status page shows the status of PPP for each PPP interface. DDNS Update Status You can view the DDNS update status of your WAN connection from the DDNS Status page. -
Page 75: Dhcp Clients
DHCP Clients The DHCP Clients page shows the MAC Address, IP Address, Host Name and Lease Time. Modem Status The Modem Status page shows the modem status and DSL statistics. -
Page 76: Product Information
Product Information The Product Information page shows the product information and software versions. System Log The System Log page shows the events triggered by the system. -
Page 77: Wds Report
WDS Report You can view the WDS report for your RG (AP) by clicking the WDS Report link from the Status main page. The WDS Report page allows you to view the following WDS-related wireless activities: •WDS configuration and states •WDS management statistics •WDS database... -
Page 78: Help
HELP This section takes you to different Help Sections for Firewall, Bridge Filters, LAN Clients and PPP Connection. Firewall Help Help for Port Forwarding, Access Control, and Advanced Security. Bridge Filter Help Help section for Bridge Filters. -
Page 79: Lan Clients
LAN Clients Help section for LAN Clients. LAN Group Configuration Help section for Configuring LAN Groups with static IP Address. -
Page 80: Ppp Connection
PPP Connection Help for establishing a PPP Connection. UPnP Help Help pages for UPnP. -
Page 81: Rip Help
RIP Help Help section for RIP (Routing Information Protocol). QoS Help Help section for IP QoS. -
Page 82: Troubleshooting
Troubleshooting This chapter gives information about troubleshooting your ADSL Router. After each problem description, instructions are provided to help you diagnose and solve the problem. For the common problems listed, go to the section indicated. Is the router on? Have I connected the router correctly? Basic Functioning Go to I can't access the router's configuration with my browser. -
Page 83: Troubleshooting The Web Configuration Interface
If all LEDs are still on one minute after power up: Cycle the power to see if the router recovers. Clear the router's configuration to factory defaults. This will set the router's IP address to 192.168.1.1. If the error persists, you might have a hardware problem and should contact technical support. -
Page 84: Using The Reset Button
Using the Reset button. Make sure your browser has Java, JavaScript, or ActiveX enabled. If you are using Internet Explorer, click Refresh to be sure the Java applet is loaded. Try quitting the browser and launching it again. Make sure you are using the correct login information. The factory default login name is Admin and the password is... -
Page 85: Obtaining A Wan Ip Address
If the telephone company has tested the ADSL signal at your Network Interface Device (NID), then you may have poor quality wiring in your house. If disconnecting telephones does not result in a green WAN LED the problem may be one of the following: Check that the telephone company has made the connection to your line and tested it. -
Page 86: Troubleshooting Pppoe Or Pppoa
Assign the computer Host Name of your ISP account to the router in the browser-based Setup Wizard. Your ISP only allows one Ethernet MAC address to connect to Internet, and may check for your computer's MAC address. In this case: Inform your ISP that you have bought a new network device, and ask them to use the router's MAC address. - Page 87 and verify the router address. Troubleshooting a TCP/IP Network Using the Ping Utility Most TCP/IP terminal devices and routers contain a ping utility that sends an echo request packet to the designated device. The device then responds with an echo reply.
-
Page 88: Restoring The Default Configuration And Password
From the Windows run menu, type: ping -n 10 <IP address> where <IP address> is the IP address of a remote device such as your ISP's DNS server. If the path is functioning correctly, replies as in the previous section are displayed. If you do not receive replies: —... -
Page 89: Appendix
Appendix Country VPI:8 Australia All Internet providers VCI:35 VPI:0 Belgium VCI:33 VPI:0 Canada Telus VCI:35 VPI:8 Cybercity VCI:35 Danmark VPI:8 Tiscali VCI:35 VPI:1 1 & 1 Internet DSL VCI:32 VPI:1 AOL DSL VCI:32 VPI:8 Arcor DSL VCI:35 VPI:1 Freenet DSL VCI:32 VPI:1 Fireline networks... - Page 90 Country VPI:8 ISRAEL KPN PPPoE LLC VCI:48 VPI:8 Telecom Italia VCI:35 Italian VPI:8 Rest oil presente VCI:35 VPI:8 KPN PPPoA VC-MuX VCI:48 VPI:0 Netherlands BBeyond Bridge LLC VCI:33 VPI:0 BBeyond PPPoA VC-MuX VCI:35 VPI:0 New Zealand New Zealand Telecom VCI:100 VPI:0 Portugal Todos os apresentador...
- Page 91 Country VPI:1 Switserland Alle anbieter VCI:32 VPI:8 Sverige Skanova VCI:35 VPI:0 Hinet VCI:33 Taiwan VPI:0 Seednet VCI:33 VPI:8 Etisalat Classical IP Single User VCI:35 United Arab Emirates Etisalat Classical IP for VPI:8 Business VCI:35 VPI:0 United Kingdom British Telecom VCI:38...