Summary of Contents for Gasoline 4500
- Page 1 OWNER’S MANUAL 4500/5200/5800 Before using our chain saws, please read this manual carefully to understand the proper use of Caution your unit. Keep this manual handy...
-
Page 2: Table Of Contents
SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern NOTES ON TYPES OF WARNINGS IN critical points which must be taken into THE MANUAL consideration to prevent possible serious bodily WARNING injury, and for this reason you are requested to read such instructions carefully and follow them without foal. -
Page 3: Parts Location
1.PARTS LOCATION 1. Front guard 2. Starter knob 3. Air cleaner 4. Choke knob 5. Throttle interlock 6. Right handle 7. Throttle lever 8. Engine switch 9. Fuel tank 10.Oil tank 11. Left handle 12.Saw chain 13. Guide bar... -
Page 4: On The Machine
2.WARNING LABELS ON THE MACHINE 3.SYMBOLS ON THE MACHINE （ （ （ （ 1） ） ） ） Carefully read owner’s manual before operating this machine For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful （... -
Page 5: Safety Precautions
4.SAFETY PRECAUTIONS BEFOR USING THE MACHINE a. Read this owner’s manual carefully to understand how to f. Lack of sleep, tiredness, or physical operate this unit properly. exhaustion results in lower attention spans, and this in turn leads to b. You should never use the accidents and injury. - Page 6 WARNINGCONSIDERING The engine of this product is designed to run on a mixed fuel which contains highly flammable gasoline. Never store cans of fuel or refill the fuel tank in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel.
- Page 7 whipped toward you or pull you Check the tree for dead branches off balance. that could fall during the felling When cutting a limb that is under operation. tension, be alert for spring back Always shut of the engine before so that you will not be struck setting it down.
-
Page 8: Installing Guide Bar
TRANSPORTATION Always carry the unit with the engine stopped, the guide bar covered with the protector to the rare, and muffler away from your body. 5. INSTALLING GUIDE BAR AND SAW CHAIN 6.FUEL AND CHAIN OIL （ （ （ （ 1 ） ） ） ） Moving 4. - Page 9 (1) Chain oil Keep open flames away from (2)Fuel the area where fuel is handled (3)Switch or stored. Mix and store fuel (4)Throttle lever only in an approved gasoline (5)Throttle interlock container. (6)Choke knob NOTE When restarting NOTE...
-
Page 10: Operating Engine
changed The carburetor on your unit has been inserting factory adjusted. But may require fine screwdriver turning due to change in operating hole conditions. bottom of the clutch side. Before adjusting the carburetor, make Adjust sure that provided are clean air/fuel according filters and fresh, properly mixed fuel. -
Page 11: Sawing
from front guard toward the front handle till cylinder Continuing “click” sound is heard. cover. use the product Reattach anti-freeze (1)Break (Front guard) the screen mode even right when (2) Released side temperatures left so as have risen and (3) Operated returned anti-icing normal... -
Page 12: Maintenance Of Engine
forbidden tree on the felling side. to cut other types of When the saw chain is 4. Make a felling cut from the opposite material. caught in the cut, do not side of the notch and at a level slightly Vibrations attempt to pull it out by higher than the bottom of the notch. - Page 13 To clean dirt in the down from the top one-third meshed, split the cleaner into halves and finish by sawing up from and brush in gasoline. When using the bottom. compressed air, blow from the inside. (F25)
- Page 14 (1) Fuel filter (b) Disassemble the filter and wash with gasoline, or replace with new one if needed. NOTE After removing the filter, use a pinch to hold the end of the suction pipe.
-
Page 15: An Guide Bar
SAW CHAIN WARNING It is very important for GUIDE BAR smooth and safe operation to Reverse the bar occasionally to keep the cutters always prevent partial wear. sharps. The bar rail should always be a Your cutters need to be square. - Page 16 Case 1. Starting failure: (1) Wrench………………………….…..1 Replace with proper fuel. Check fuel for water or (2) Adjust screwdriver………………….1 substandard mixture (3) Internal six spanner s3…………….1 Remove and dry the spark plug. (4) Internal six spanner s4…………….1 Then pull the starter again with Check for engine no choke.
-
Page 17: Specifications
13. SPECIFICATIONS Model 4500 5200/5800 External dimension: LXWXH 412x260x272 412x265x275 Mass: saw without guide bar and chain, empty tanks Volume: Fuel tank Tank for chain lubrication oil Fuel (Mixture ratio) 25:1;2-cycle engine oil Oil (Chain oil) Special chain oil or motor oil...