Advertisement
Notes
• W hen installing the camera on a ceiling not to disturb adjustment ofTilt Base angle fix
theBNC-PowerCableonthePanBaseclip.
Pan Base Clip
BNC-Power Cable
Connection to Power
• Connect the adapter to the power input connector as shown in the figure below.
Use a DC 12V. (The Adapter is not provided with the Dome Camera.)
DOMECamera
PowerInputConnector
Adapter(notprovided)
MINI DOME CAMERA
8
USER'S MANUAL
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized
technician.
◾ The image on the screen is dim.
• Check if the lens are stained. If dirty, clean the lens with soft, clean cloth.
• T he image is dimmer at night than daytime. If the focus is not right, adjust it at
daytime.
◾ The contrast on the screen is too weak.
• Adjust the contrast feature of the monitor.
• If the camera is exposed under too strong light, change the camera position.
• Adjust the lens BACK FOCUS again.
◾ The camera is not work properly, and the surface of the camera case is hot.
• Check that you have connected the camera to a proper power (DC 12V)
MINI DOME CAMERA
12
USER'S MANUAL
For DC Power Type
Resistance of copper wire [at 20Cº(68ºF)]
• As the voltage drop according to the length of the cable in the above table,
a camera may malfunction if there is an excessively long cable run.
* Voltage for camera operation: 12V DC ±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.
Connection to Monitor
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
• As a connecting method varies according to instruments, refer to the manual supplied
with the instrument.
• Connect the cable after power is turned off.
• Set the 75Ω / Hi-Z selection switch. If it is a intermediate device, switch it to Hi-z
and if it is final device, switch it to 75Ω. (Please refer to the Monitor Manual.)
DOMECamera
Intermediate
Monitor
BNC
MINI DOME CAMERA
9
USER'S MANUAL
MINI DOME CAMERA
13
USER'S MANUAL
Panning & Tilting Control
You can adjust the Panning and Tilting angle freely. (Panning angle: 360º, Tilting
angle: 20º~90º)
Tilt Base
You can adjust up and down
Tilt Base Holding
the camera (20º~90º).
Screws
Pan Base
Pan Base
You can rotate the lens
Holding Screw
from 360
1) Adjustment Panning angle: After attaching the dome camera to a ceiling, adjust the
panning angle for better monitoring area by rotating the Pan Base. The panning angle
can be adjusted 360º freely.
2) Adjustment Tilting angle: After attaching the dome camera to a ceiling, adjust the
tilting angle for better monitoring area by rotating the Tilt Base. The tilting angle
can be adjusted to 20º from 90º freely. (based the ceiling surface)
Notes
• AfterlooseningPanorTiltBaseholdingscrews,adjustitsangle.Andthentightenscrewsagain.
• I ncaseofadjustingthetilting,donottakethelensforpreventinghysicalshocks.PleasetaketheTiltBase.
• T hisdomecameraistobeinstalledontheceilingbyfactorydefault.
MINI DOME CAMERA
10
USER'S MANUAL
MINI DOME CAMERA
14
USER'S MANUAL
MINI DOME CAMERA
11
USER'S MANUAL
Application of Council Directive(s)
89 / 336 / EEC
Manufacturer's Name
SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment
MINI DOME CAMERA
Model Name
SID-53/56
Beginning Serial NO.
S6300001
Year of Manufacture
2009. 01. 01
Conformance to
EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s).
Manufacturer
SAMSUNG TECHWIN CO., LTD
Legal Representative in Europe
Signature
Signature
Full Name
HAN SEUG KIM
Full Name
Position
QUALITY CONTROL MANAGER
Position
Place
CHANGWON, KOREA
Place
Date
2009. 01. 01
Date
MINI DOME CAMERA
15
USER'S MANUAL
Advertisement
