Table of Contents
Advertisement
Quick Links
PRUNER ATTACHMENT
to LK PBT3446 AUTO MULTITOOLS
(Model PBT3446TP)
Translation of the original instructions for use
WARNING: Read the instructions before using the product
Before initial start-up, please read through these operating instructions
carefully prior to using the machine. Keep the instructions safe and pass them
on to any subsequent user so that the information is always available.
Serial Number:
BRUSHCUTTER
Advertisement
Table of Contents
Related Manuals for Lawn-King PBT3446TP
Summary of Contents for Lawn-King PBT3446TP
- Page 1 PRUNER ATTACHMENT BRUSHCUTTER to LK PBT3446 AUTO MULTITOOLS (Model PBT3446TP) Translation of the original instructions for use WARNING: Read the instructions before using the product Before initial start-up, please read through these operating instructions carefully prior to using the machine. Keep the instructions safe and pass them on to any subsequent user so that the information is always available.
- Page 2 Fig. 1...
- Page 3 Fig. 2 Fig. 3 Fig. 4...
- Page 4 Fig. 6 Fig. 5 Fig. 7 Fig. 8 Fig. 9...
- Page 5 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14...
- Page 6 Fig. 15 Fig. 16 Fig. 18 Fig. 17 Fig. 20 Fig. 19...
- Page 7 Fig. 21 Fig. 23...
- Page 8 PRUNER INSTRUCTIONS MANUAL Thank you for choosing one of our garden products This product has been manufactured taking into The pruner attachment can only account the applicable safety regulations issued to be fitted on LK PBT3446 AUTO protect consumers. MULTITOOLS brush cutter and used with it.
- Page 9 PRUNER INSTRUCTIONS MANUAL OPERATION: - Operator has poor circulation to his – Only use the pruner hands. attachment for pruning (cutting - The pruner is used in cold weather (wearing warm gloves is strongly branches) and only for cutting wood. Do not use the equipment for other recommended).
- Page 10 PRUNER INSTRUCTIONS MANUAL B10.1 – The THROTTLE TRIGGER 1) Fit the pruner attachment (fig. 3 part 1) to the LOCKOUT (see Brush Cutter lower drive rod (fig. 3 part 2) being careful to manual) stops accidental operation correctly fit the drive shaft (fig. 3 part 3) in the of the throttle control lever.
-
Page 11: Starting And Stopping
PRUNER INSTRUCTIONS MANUAL 3) An oil different to that recommended could cause damage to the bar, to the chain and to Fig.24 the lubrication system. 6. REFUELLING (refer to Brushcutter manual. The same conditions apply). BELT HOOK AND FIXING RING (Fig. 11) (refer to Brush Cutter manual. -
Page 12: During Operation
PRUNER INSTRUCTIONS MANUAL WARNING! The cutting device will Always hold the hedge trimmer with both continue to rotate for some time even hands. after moving the switch to the “OFF” Cut by pressing the accelerator lever as far position. Firmly hold the two handles as it will go and enter into contact with the until the cutting device comes to a wood when the motor is running at top... -
Page 13: Maintenance And Transport
PRUNER INSTRUCTIONS MANUAL 9. MAINTENANCE AND TRANSPORT - Position the file so it protrudes by about 1 mm (fig.22 part.4) above the level of the cutting edges. For maintenance operations relating to the engine, see the enclosed Brush Cutter manual. 9.2 CHAIN CHANGING AND TENSIONING CHECKING THE SCREWS AND MOVING... - Page 14 PRUNER INSTRUCTIONS MANUAL TRANSPORT During transport (including for chain can be raised with two fingers to the point where an entire guide tooth is visible (Fig.26). short distances) position the chain protection (pict. 23). ALWAYS USE GLOVES EVERY TIME YOU NEED TO FIT OR REMOVE THE Fig.26 CHAIN PROTECTION.
-
Page 15: Technical Data
PRUNER INSTRUCTIONS MANUAL TECHNICAL DATA 1.5 Kg Pruner attachment weight Pruning equip. + LK PBT3446 7.2 Kg AUTO MULTITOOLS unit 25 cm Cutting device (bar) EC DECLARATION OF CONFORMITY The undersigned, certifies that the following product: PRUNER ATTACHMENT fitted onto the motorized units LK PBT3446 AUTO MULTITOOLS is in compliance with directive 98/37/EEC and has been developed in compliance with EN ISO 12100, EN ISO 11680-1 standards together with the aforementioned motorized units.