Tennant SpeedScrub 2401 Operator's Manual
  1. Manuals
  2. Brands
  3. Tennant Manuals
  4. Accessories
  5. SpeedScrub 2401
  6. Operator's manual
Tennant SpeedScrub 2401 Operator's Manual

Tennant SpeedScrub 2401 Operator's Manual

Automatic scrubber
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SpeedScrub
2401 & 2601
Automatic Scrubber
Model No.s: 603201 & 603202
Operator Manual
EN
EN
603409
Rev. 00 (04 97)
Home
Find... Go To..

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SpeedScrub 2401 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Tennant SpeedScrub 2401

Summary of Contents for Tennant SpeedScrub 2401

  • Page 1 SpeedScrub 2401 & 2601 Automatic Scrubber Model No.s: 603201 & 603202 Operator Manual 603409 Rev. 00 (04 97) Home Find... Go To..

  • Page 2: Table Of Contents

    ..... . EC DECLARATION OF CONFORMITY FOR MACHINERY (Directive 89//392/EEC,Annex II, sub A) TENNANT N.V. models: SPEEDSCRUB 2401/2601 nr.: 603201 & 603202 Address: Industrielaan 6 5405 AB – is in conformity with the provisions of the Machinery Directive ( Directive 89/392/EEC), P.O.

  • Page 3: Safety Precautions

    Do not run machine where flammable liquids or gases are present. – Do not run on ramps or inclines unless adequate personnel are present for assistance. – Always use extreme caution when maneuvering. SpeedScrub 2401/2601 (04–97) Home Find... Go To..

  • Page 4: Standard Machine Components

    Left Side Brush Motor Solution Flow Circuit Breaker Reverse Brush Vacuum Battery Charge Motor Circuit Squeegee Up Meter Breaker Less Brush Pressure Main Power More Brush Squeegee Down Brush Pressure Circuit Breaker Pressure Meter SpeedScrub 2401/2601 (04–97) Home Find... Go To..

  • Page 5: Machine Installation

    1. Set parking brake. Brake lever is located behind right side drive wheel. (Figure 1) 6. Turn key and main switch on and check battery meter charge level. Charge if necessary. (See BATTERY CHARGING) FIG. 1 SpeedScrub 2401/2601 (04–97) Home Find... Go To..

  • Page 6: Machine Setup

    (Figure 6) your specific cleaning need. 5. (For Pad Installation) Attach pads to pad drivers before connecting drivers to motor hubs. Secure pads with plastic centerlock ring. (Figure 9) FIG. 6 SpeedScrub 2401/2601 (04–97) Home Find... Go To..

  • Page 7: Filling Solution Tank

    1. Release parking brake lever if set. increment markers to indicate amount of 2. Adjust control grips to a comfortable operating water in tank. (Figure 11) height, squeeze together the two levers below the console. (Figure 12) SpeedScrub 2401/2601 (04–97) Home Find... Go To..
  • Page 8 6. Turn on the vacuum and brush/solution (SCRUB or STRIP). Never operate machine switches. in red zone. Depress brush pressure switch to properly adjust brush pressure. (Figure 17) SpeedScrub 2401/2601 (04–97) Home Find... Go To..

  • Page 9: While Operating Machine

    9. During brief stops, you do not have to turn off any switches, the brushes and solution flow will automatically stop when control grips are released. 10. Periodically check battery meter discharge level. When needle drops to the red zone, recharge batteries. SpeedScrub 2401/2601 (04–97) Home Find... Go To..

  • Page 10: Stopping Machine

    The power kill button immediately stops all power to machine. (Figure 21) To reset power kill button, shut off all switches and turn kill button to the right. Resume to normal operation. FIG. 22 SpeedScrub 2401/2601 (04–97) Home Find... Go To..

  • Page 11: Draining Tanks

    2. Turn off all switches and key. 1. Pull clear hose off hose barb at rear of machine and drain solution into floor drain or 3. Hinge open recovery tank to access batteries. bucket. (Figure 24) (Figure 25) SpeedScrub 2401/2601 (04–97) Home Find... Go To..

  • Page 12: Maintenance

    1. Remove and clean pads or brushes. Never charger MUST be grounded while in use to use soiled pads when cleaning. Replace pads protect user from electric shock and serious when they become worn or loaded with injury. residue. SpeedScrub 2401/2601 (04–97) Home Find... Go To..

  • Page 13: Weekly Maintenance

    4. Check for loose or worn cables. Replace if 3. Check machine for water leaks and loose nuts worn. and bolts. SpeedScrub 2401/2601 (04–97) Home Find... Go To..

  • Page 14: Transporting Machine

    5. Place tie–down straps over top of machine and secure straps to floor. It may be necessary to install tie–down brackets to the floor of your trailer or truck. SpeedScrub 2401/2601 (04–97) Home Find... Go To..

  • Page 15: Trouble Shooting

    Short run time. Batteries not fully charged. Charge batteries. Bad cell in one or more batteries. Replace battery. Batteries need maintenance. See BATTERY MAINTENANCE. Faulty charger. Replace battery charger. SpeedScrub 2401/2601 (04–97) Home Find... Go To..

  • Page 16: Specifications

    WATER LIFT 68”/172cm 68”/172cm BATTERIES 2–12V, 215AH 2–12V, 215AH RUN TIME PER CHARGE Up to 4 3/4 hours Up to 4 3/4 hours DECIBEL RATING AT OPERATOR’S 75dB(A) 75dB(A) EAR, INDOORS ON TILE. SpeedScrub 2401/2601 (04–97) Home Find... Go To..

This manual is also suitable for:

Speedscrub 2601603201603202

Table of Contents