200hz lcd tv signature series in full hd, premium series in full hd, true cinematic series, modern classic series, sleek & stylish series, home theatre systems, portable dvd players (2 pages)
HISTORY INFORMATION FOR THE FOLLOWING MANUAL: FIXP SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KDL-70XBR3 RM-YD013 ORIGINAL MANUAL ISSUE DATE: 2/2007 :UPDATED ITEM REVISION DATE SUBJECT 2/2007 No revisions or updates are applicable at this time. 4/2007 Reissue entire manual to include Disassembly insturctions.
Page 2
Self Diagnosis Supported model FIXP SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KDL-70XBR3 RM-YD013 KDL-70XBR3 LCD DIGITAL COLOR TELEVISION 9-883-735-02...
KDL-70XBR3 TABLE OF CONTENTS SECTION TITLE PAGE SECTION TITLE PAGE Specifi cations ................. 4 BEP Board Schematic Diagram (1 of 13) ......34 BEP Board Schematic Diagram (2 of 13) ......35 Warnings and Cautions ..............6 BEP Board Schematic Diagram (3 of 13) ......36 Safety-Related Component Warning ..........
Macintosh is a trademark licensed to Apple Computer, Inc., registered in the U.S.A and other countries. Blu-ray Disc is a trademark. “BRAVIA” and are trademarks of Sony Corporation. “x.v.Color” is a trademark of Sony Corporation. ® As an ENERGY STAR Partner, Sony Corporation has ®...
Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont l’importance est critique pour la securite du fonctionnement sont identifi...
KDL-70XBR3 SAFETY-RELATED COMPONENT WARNING There are critical components used in LCD color TVs that are important for safety. These components are identifi ed with shading and mark on the schematic diagrams and the electrical parts list. It is essential that these critical parts be replaced only with the part number specifi...
Page 8
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com KDL-70XBR3...
KDL-70XBR3 SAFETY CHECK-OUT The AC leakage from any exposed metal part to earth ground and After correcting the original service problem, perform the following from all exposed metal parts to any exposed metal part having a safety checks before releasing the set to the customer: return to chassis, must not exceed 0.5 mA (500 microamperes).
KDL-70XBR3 Self Diagnosis SELF-DIAGNOSTIC FUNCTION Supported model The unit in this manual contains a self-diagnostic function. If an error occurs, the STANDBY LED will automatically begin to fl ash. The number of times the LED fl ashes translates to a probable source of the problem. A defi nition of the STANDBY LED fl ash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 11
KDL-70XBR3 Diagnostic Test Indicators When an error occurs, the STANDBY LED will fl ash a set number of times to indicate the possible cause of the problem. If there is more than one error, the LED will identify the fi rst of the problem areas. If the errors occur simultaneously, the one that corresponds to the fewest fl ashes is identifi ed fi...
KDL-70XBR3 SECTION 1: DISASSEMBLY 1-1. OVERVIEW The KDL70XBR3 has considerable weight due to its size. The set weighs approximately 205 lbs (93Kg) with the base stand and approximately 176 lbs (80Kg) without. Please review the following guidelines before repairing the set.
KDL-70XBR3 1-7. SPEAKER REMOVAL Remove 2 screws, +PWH 4X16 1-8. G1P BOARD REMOVAL Note: If necessary, one Arm bracket can be removed. DEP Board Remove 4 screws, +PSW M3X8 NOTE: The DEP Board contains critical Disconnect 8 connectors adjustment data, therefore, replacement is not available.
KDL-70XBR3 1-13. FRONT CABINET, BASE STAND, AND ARM BRACKET REMOVAL Remove 6 screws from upper stays, +BVTP2 4X16 Remove 12 screws from vertical stays on both sides, +BVTP 3X12 TYPE2 IT3 Remove 8 screws from lower stay, +BVTP2 4X16 Remove 11 screws per arm, +PSW M4X8...
KDL-70XBR3 3-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS INFORMATION The components identifi ed by shading and symbol are critical for safety. Replace only with part number specifi ed. All capacitors are in μF unless otherwise noted. pF : μμF 50WV or...
KDL-70XBR3 3-3. BLOCK DIAGRAMS Analog Video Signal SYSTEM BLOCK DIAGRAM Analog Audio Signal Digital Video Signal Digital Audio Signal HDMI 1 HDMI 3 UART UART UART A-AU HDMI Format Axilleus FLASH Conv. Sil9011 LVDS MFV2.5 IFP2S LVDS SPDIF SDRAM CCPXA...
KDL-70XBR3 3-4. SCHEMATICS AND SUPPORTING INFORMATION AUP BOARD SCHEMATIC DIAGRAM (1 OF 7) V 1_IN R 8011 1/10W V 1_Y R 8014 R 8017 V D8013 1/10W 1/10W RN-CP RN-CP V 1_C — R 8013 R 8016 R 8020 V D8014...
See Appendix A: Encryption Key Components in the back of this manual. (Check the Sony Electronics Service Information website for any additional service related issues for this model.) 4-1. REAR COVER ASSEMBLY 7-685-648-79...
See Appendix A: Encryption Key Components in the back of this manual. (Check the Sony Electronics Service Information website for any additional service related issues for this model.) 4-2. H BOARDS AND SPEAKERS 7-685-648-79...
DEP BOARD, MOUNTED (The DEP Board contains critical adjustment data, therefore, replacement is not available. (Check the Sony Electronics Service Information website for any additional service related issues for this model.) Please contact your service representative for additional information. ) 4-3.
See Appendix A: Encryption Key Components in the back of this manual. 1-834-167-11 LEAD WIRE WITH CONNECTOR (LVDS) (Please refer to the Disassembly section for disconnection and installation instructions.) (Check the Sony Electronics Service Information website for any additional service related issues for this model.) 1-910-034-23 HARNESS ASSEMBLY (T-CON) 4-4 CONNECTORS...
See Appendix A: Encryption Key Components in the back of this manual. (Check the Sony Electronics Service Information website for any additional service related issues for this model.) 4-5. CABINET AND STAND ASSEMBLIES, AND H4 BOARD 7-685-648-79...
KDL-70XBR3 SECTION 5: ELECTRICAL PARTS LIST Items marked with an asterisk are not stocked since they NOTE: The components identifi ed by shading RESISTORS are seldom required for routine service. Expect some delay mark are critical for safety. Replace only •...
Page 92
KDL-70XBR3 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R8533 1-216-833-11 METAL CHIP 1/10W R8634 1-218-950-11 RES-CHIP 1/16W R8534 1-216-833-11 METAL CHIP 1/10W R8635 1-218-950-11 RES-CHIP 1/16W R8638 1-218-961-11 RES-CHIP 4.7K 1/16W R8535 1-216-817-11 METAL CHIP...
Page 93
KDL-70XBR3 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R8803 1-218-969-11 RES-CHIP 1/16W R8853 1-218-867-11 METAL CHIP 6.8K 0.50% 1/10W R8804 1-218-973-11 RES-CHIP 1/16W R8854 1-216-833-11 METAL CHIP 1/10W R8855 1-218-887-11 METAL CHIP 0.50% 1/10W R8805...
Page 94
KDL-70XBR3 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R9003 1-218-990-81 SHORT CHIP R9048 1-218-961-11 RES-CHIP 4.7K 1/16W R9004 1-218-990-81 SHORT CHIP R9049 1-218-989-11 RES-CHIP 1/16W R9050 1-218-977-11 RES-CHIP 100K 1/16W R9005 1-218-990-81 SHORT CHIP R9006...
Page 95
KDL-70XBR3 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R9102 1-218-990-81 SHORT CHIP R9332 1-216-864-11 SHORT CHIP R9103 1-218-990-81 SHORT CHIP R9333 1-216-864-11 SHORT CHIP R9334 1-216-864-11 SHORT CHIP R9104 1-218-990-81 SHORT CHIP R9105 1-218-990-81 SHORT CHIP...
Page 97
KDL-70XBR3 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R9626 1-218-990-81 SHORT CHIP R9679 1-218-965-11 RES-CHIP 1/16W R9627 1-218-990-81 SHORT CHIP R9680 1-218-957-11 RES-CHIP 2.2K 1/16W R9681 1-218-990-81 SHORT CHIP R9628 1-218-965-11 RES-CHIP 1/16W R9629 1-218-965-11...
Page 98
KDL-70XBR3 NOTE: The components identifi ed by a red outline and a mark contain confi dential information. Specifi c instructions must be adhered to whenever these components AUP BEP are repaired and/or replaced. See Appendix A: Encryption Key Components in the back of this manual.
Page 121
KDL-70XBR3 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only F G1P que par une piece portant le numero specifi e.
Page 122
KDL-70XBR3 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 124
KDL-70XBR3 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 125
KDL-70XBR3 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES Q6800 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF R6156 1-218-879-11 METAL CHIP 0.50% 1/10W Q6801 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF R6157 1-216-837-11 METAL CHIP 1/10W R6159 1-218-895-11 METAL CHIP 100K 0.50% 1/10W R6162...
Page 126
KDL-70XBR3 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R6432 1-218-863-11 METAL CHIP 4.7K 0.50% 1/10W R6555 1-218-853-11 METAL CHIP 1.8K 0.50% 1/10W R6433 1-216-833-11 METAL CHIP 1/10W R6600 1-202-933-61 FUSIBLE 1/2W R6601 1-216-857-11 METAL CHIP...
Page 127
KDL-70XBR3 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only G1P G2P que par une piece portant le numero specifi e.
Page 132
KDL-70XBR3 LD3 LP3 LT3 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R3102 1-216-864-11 SHORT CHIP R3103 1-216-813-11 METAL CHIP 1/10W R3105 1-216-813-11 METAL CHIP 1/10W A-1223-740-A LP3 BOARD, COMPLETE R3106 1-216-851-11 METAL CHIP 330K 1/10W Due to the complexity of this board, performing component level fi...
MUST BE RETURNED to Sony. b) and if the core charge is NOT covered under the product warranty, the defective un-repaired or modifi...
Page 135
In an effort to reduce the size of this pdf file the tiled schematics are not attached to this Service Manual. To receive a complete set of the tiled schematics for this manual please submit a request to the Service Promotion Department at Service_Promotion@am.sony.com.