Related Manuals for Xitrix TravelPro Series
Summary of Contents for Xitrix TravelPro Series
-
Page 1: Troubleshooting Guide
Xitrix TravelPro Series Installation and Troubleshooting Guide www.xitrix.com support.xitrix.com... - Page 2 Notice The information in this user’s manual is subject to change without notice. THE MANUFACTURER OR RESELLER SHALL NOT BE LIABLE FOR ERRORS OR OMISSIONS CONTAINED IN THIS MANUAL AND SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES, WHICH MAY RESULT FROM THE PERFORMANCE OR USE OF THIS MANUAL.
-
Page 3: Table Of Contents
Side Views (1-8,9) Bottom View (1-10,11) AC Adapter (1-12) LED Status Indicators (1-13) Keyboard Features (1-14) Function (Quick) Keys (1-14) Windows Keys (1-15) Embedded Numeric Keypad (1-15) Touch Pad (1-16) Graphic Subsystem (1-17) Adjusting the Display Brightness (1-17) Extending the Life of the TFT Display Panel (1-17) Opening and Closing the Display Panel (1-18) Audio Subsystem (1-19) Adjusting the Volume in Windows (1-19) -
Page 4: Using This Manual
Display Problems (5-8) Keyboard and Mouse Problems (5-9) CMOS Battery Problems (5-10) Memory Problems (5-11) Modem Problems (5-12) Network Adapter / Ethernet Problems (5-13) PC Card / PCMCIA Problems (5-14) Performance Problems (5-15) USB2.0 Problems (5-16) APPENDIX A Product Specification APPENDIX B Agency Regulatory Notices Preface Using This Manual... - Page 5 given instructions or information could result in damage to your computer or could cause bodily harm or loss of life. Protecting Your Computer - Avoid Abusive Handling and Adverse Environment Follow the advice below will help ensure that you get the most out of your Investment.
- Page 6 Notebook uses exclusively the AC adapter: Lishin 0335C2065 (65W), Liteon PA-1650-01 (65W), HIPRO HP-OK065E03 (65W) RTC BATTERY: Vic-Dawn Enterprise Co., Ltd/ CR2032 CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions.
-
Page 7: Chapter Summaries
washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak. - Page 8 In this chapter, you will learn how to change various firmware settings and what the settings mean. Also, you will learn how to take advantage of the built-in security feature provided by the BIOS. Chapter 3: Battery Power & Power Management In this chapter, you will learn the fundamentals of power management and how to use them to achieve longer battery life.
-
Page 9: Getting To Know The Basics
CHAPTER▼ ONE GETTING TO KNOW THE BASICS This chapter introduces the features and components of the computer. Performance Features High Performance Processor with Intel Chipset The notebook PC is equipped with a powerful Intel Merom CPU 。 Together with the latest Intel chipset and technologies, the system offers very advanced PC performances. -
Page 10: System At A Glance
The system offers upgradeable hard disk drive and 2 DDR SDRAM sockets for expansion, allowing the user to easily increase the storage and system capacities as the need arises. Built-in Multiple Card Reader There is built-in 4-in-1 card reader to access many of the portable media formats (SD Card, MS Card, MMC Card, and MS-Pro Card). - Page 11 1. LCD Latch The LCD latches lock / unlock the LCD panel. 2. LCD Display The panel is where the system content is displayed. 3. Built-in Stereo Speakers The built-in speakers output the sound in stereo. 4. Keyboard The keyboard is used to enter data. (See Keyboard Section for details.)
- Page 12 5. Touch Pad The touch pad is a built-in pointing device with functions similar to a mouse. 6. LED Status Indicator The LED Status indicators reveal the status of these functions: Numeric keypad, cap lock, silent mode, WLAN module enabling and disabling and also the ODD, HDD activities.
- Page 13 Warning: Do not place any heavy objects on the top of notebook. This may damage the display 1. Wireless On/Off Switch Use the Switch to disable or enable the Wireless function. When Wireless LAN function is enabled, the LED status indicator shows steady green light.
- Page 14 damage the display 1. USB2.0 Port (x3) The Universal Serial Bus (USB2.0-compliant) port allows you to connect a wide variety of devices to your computer at a rate of up to 480 Mbps. This port conforms to the latest USB2.0 plug-and-play standards.
-
Page 15: Bottom View
The slot is where ExpressCard (TypeII, 54mm) is inserted. ExpressCard Type 54 allows insertion of either 54mm or 34mm cards. ExpressCard integrates both the PCI-Express bus technology and USB2.0 interface. 10. 4-in-1 Card Reader The 4-in-1 Card Reader supports SD Card, MS Card, MMC Card, and MS-Pro Card. -
Page 16: Ac Adapter
2. Ventilation Grill The fan grill is where air is exchanged to dissipate the internal heat. Do not block this airway completely. Warning: Do not block the Fan Grill outlet. Place the machine on hard surface only. The bottom case may get very hot. 3. -
Page 17: Led Status Indicators
Note : , You may feel a slight tingling sensation on any of the computer’s metal parts such as the I/O ports. This is caused by leakage current when the AC adapter is not properly grounded (via the ground pin). However, the amount of leakage current is within the safety regulation and is not harmful to human body. -
Page 18: Keyboard Features
Keyboard Features Function Keys (Quick Keys) Graphic Action System Control Symbol Fn + F1 Enters Suspend Mode. Fn + F3 Turns of the battery warning beep off or on. Fn + F4 Changes Display Mode: LCD-only, CRT-only and LCD&CRT. Fn + F5 Turns Speaker Volume up. -
Page 19: Embedded Numeric Keypad
2. Application Menu Key This key brings up the popup menu for the application, similar to a click of the right mouse button. Embedded Numeric Keypad Press Fn+Num Lk to enable the embedded numeric keypad. The numbers are printed in upper right corner of a key, in a color different from the alphabets. -
Page 20: Graphic Subsystem
Access Click Context once Menu Move One Page Up or Down Tips on Using the Touch Pad: 1. The double-click speed is timed. If you double-click too slowly, your notebook responds as if you single-clicked twice. 2. Keep your fingers dry and clean when using the touch pad. Also keep the surface of touch pad clean and dry to prolong its life. -
Page 21: Opening And Closing The Display Panel
Opening and Closing the Display Panel To open the display, push the LCD latch to the right and lift up the lid. Then tilt it to a comfortable viewing position. To close the display cover, fold it down gently. Warning: To avoid damaging the display, do not slam it when closing. - Page 22 Connecting the Modem 1. Plug one end of the phone line into the modem port located on the rear side of the computer. (For EMI compliance, you need to clip the included EMI CORE to the phone line.) Plug the other end of the line into the analog phone wall outlet.
- Page 23 Your computer is equipped with a 10/100Base-TX Fast Ethernet network adapter. Connect the active LAN cable to the RJ-45 LAN port located on the right side of the computer. This allows you to access and transmit data in the local area network. Connecting to the Network Use Unshielded Twisted Pair (UTP) Ethernet cable only.
-
Page 24: Bios Setup And Security
CHAPTER▼ TWO BIOS SETUP AND SECURITY FEATURE In this chapter, you will learn how to enter the BIOS Setup Menu and manipulate various hardware control settings. You will also learn how to use the built-in security features. Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output System). -
Page 25: Entering The Bios Setup Screen
Entering the BIOS Setup Screen First turn on the power. When the BIOS performs the POST (Power-On Self Test), press F2 key quickly to activate the AMI BIOS Setup Utility. Note: You may need to press F2 key fairly quickly. Once the system begins to load Windows, you may have to retry by cycle-power on again Leaving the BIOS Setup Screen When you have finished modifying the BIOS settings, exit the BIOS. -
Page 26: Main Setup
Each menu item is described in this section. Main Setup Under this menu, you may change time/date and view basic processor and system memory information. Item Selections / Description Sub-menu Date Type in the current date, in MM/DD/YY format. Time N/A Type in the current date, in HH:MM:SS format. -
Page 27: Boot Setup
LCD Auto Enable [Enable]: The system DIMM Disable automatically reduces the LCD Function brightness when AC power is removed to save power. [Disable]: The LCD brightness remains the same whether or not AC power is present. [Enable]: The system Enable Backlight Disable automatically reduces the... -
Page 28: Security Setup
Removable Set the type of device for the 1st Dev. drive BIOS attempts to boot from. If Boot CD/DVD Realtek Boot Agent is selected, Device Hard Drive system will attempt to load boot Realtek Boot sector from the Ethernet port. Agent Disabled Set the... -
Page 29: Power Setup
Item Selections / Description Sub-menu Change Install or Change the Password Supervisor Password Change Install or Change the User Password Password Boot Sector Disabled To enable or disable the Virus Enabled boot sector protection. Protection When Enabled, BIOS gives a warning when any program attempts to rewrite or delete the boot sector. -
Page 30: Exit Setup
Item Selections Description /Sub-menu Intel Automatic [Automatic]: CPU adjusts its SpeedStep Minimum frequency automatically (on tech. Speed AC power or battery power) to save battery life. Maximum [Minimum Speed]: CPU Speed performance is minimized to Disabled save battery life. [Maximum speed]: CPU performance is maximized. - Page 31 Item Selections Description /Sub-menu Saves After you have completed the BIOS Changes settings, select this item to save all and Exit settings, exit BIOS Setup utility, and reboot. New system settings will take effect on next power-up.F10 key can be used for this operation Discard Discards changes done so far Changes...
-
Page 32: Battery Power & Power Management
CHAPTER▼ THREE BATTERY POWER & POWER MANAGEMENT In this chapter, you will learn the fundamentals of power management and how to use it to achieve longer battery life. this chapter, you will learn how to operate your notebook on battery power, how to handle and maintain the battery pack, and learn about the system’s power saving features. -
Page 33: Battery Low-Power Warning
Note: It is necessary that you charge the battery pack for at least 6 hours before using it for the first time. Note: In the Standby Suspend mode, a fully charged battery loses its power in roughly 1/2 day or less. When not being used, the battery’s power will deplete in 1-2 month. -
Page 34: Charging The Battery And Charging Time
To Install the Battery Pack: 1. Place the notebook bottom-side up on a flat and secured surface. Carefully insert the battery pack into the battery compartment of the notebook. Charging the Battery and Charging Time To charge the battery, while the battery pack is in the notebook, plug the AC adapter into the notebook and an electrical outlet. -
Page 35: Checking The Battery Level
the battery may not be fully charged. You need to continue to charge it with the AC adapter plugged in until the charging LED turns green. Checking the Battery Level You can check the remaining battery power in the Windows battery status indicator, which is located at the lower right-hand corner of the task bar. -
Page 36: Windows' Power Schemes
may enter time-out values for display and hard disk drive. Windows power manager saves power by turning off hard drive after 1 minute of inactivity, for example. Windows’ Power Schemes The power management control panel in Windows XP, known as Power Schemes, is designed to provide the user with an easy-to-use interface. -
Page 37: Suspend Mode
Running on batteries column. Lower time-out values will save more battery power. Note: Also consult Windows user guide for more information on how to use Windows power management functions. Note: Actual dialogue box shown above may appear slightly different. Suspend Mode Standby Suspend The system automatically enters this mode after a period of inactivity, which is set in the Power Schemes dialog box. -
Page 38: Power Button Action
Note: Do not install or remove the memory module when the system is in the suspend mode. Note: Actual dialogue box shown above may appear slightly different. Power Button Action The notebook PC’s power button can be set to turn off the system or activate the suspend mode. -
Page 39: Low Battery Warning
Note: Actual dialogue box shown above may appear slightly different. Warning: In the When I close the lid of my portable computer pull-down menu, DO NOT select Do nothing - otherwise the system will still run at high speed while the processor’s fan grill is fully blocked by the closed LCD panel. -
Page 40: Power Manual Quick Access
Note: Consult Windows user guide for more information on how to use Windows power management functions. Note: Actual dialogue box shown above may appear slightly different. Power Menu Quick Access Instead of making specific selections in the Power Options Properties box, you can quickly and easily specify which pre-set power saving function you desire by clicking on the Battery icon at the lower right-hand corner of the task bar. -
Page 41: Upgrading Your Computer
CHAPTER▼ FOUR UPGRADING YOUR COMPUTER In this chapter, you will learn how to upgrade the DRAM, hard disk drive, and to install the optional wireless LAN mini-Card. Warning: We strongly recommend that you return the notebook to the dealer or the shop for the hardware upgrade. Before you perform the hardware upgrade, please turn off the system, unplug the AC adapter, remove the battery pack and also disconnect the LAN and Modem cables first for your safety. - Page 42 Warning: Hard drive upgrade is a delicate process. Please observe the following instructions carefully or have a qualified technician install it for you. Damages due to mishandling of this procedure are NOT covered by the manufacture’s warranty. Warning: Apply care when handling the hard disk. Do not drop or apply any shock.
- Page 43 5. Locate and remove 2 Screw B’s. Push the HDD module to the right and separate it from the connector. Lift the module away from the bay.
-
Page 44: Upgrading The System Memory
7. Locate and remove 4 Screw C’s from the HDD module. Remove the metal case. 8. Re-attach the metal cover to the new hard drive and tighten 4 Screw C’s. Re-attach the HDD module to the HDD connector. And re- attach 2 Screw B’s. - Page 45 keyboard. You can increase the amount of memory by replacing the existing one with a dual inline memory module (commonly known as SO-DIMM) of a higher capacity. The SO-DIMM can be 512MB, or 1024MB in capacity. The SO-DIMM is of type DDR2 SDRAM, has 200 pins and runs on 1.8V.
- Page 46 Remove the System Device Cover. The DIMM socket is now seen as shown below. 5. If you need to remove an old DIMM from the socket, press out on the latches located on both edges of the socket at the same time. The DIMM should pop up to an angle of 30 degree (see diagram below).
- Page 47 8. Put the System Device Cover back and tighten 9 Screw A’s. To install the DIMM under the keyboard, do the following: 1. Remove Screw D. 2. Find the keyboard latches near the edges of the keyboard. The latch is spring-loaded. It will retract when pressed and revert back to its original position when released.
- Page 48 Carefully lift up the top edge and position the keyboard out of the way and the following is revealed. Locate and remove 2 Screw E’s on the Metal Cover. 4. If you need to remove an old DIMM from the socket, press out on the latches located on both edges of the socket at the same time.
- Page 49 5. Install the new DIMM module into the memory socket. The DIMM will only fit in one orientation. Insert the DIMM at an angle of approximately 30 degrees into the empty memory socket. Then press it firmly so that the contact edge is driven into the receiving socket.
-
Page 50: Optional Device
Congratulations! You have just completed the memory upgrade. When you boot up the computer, you should expect to see an increase in DRAM capacity. Note: Your computer has been tested with a wide range of DIMM on the market. However, not all memory modules are compatible. Check with your system vendor for a list of compatible DIMM for your computer. - Page 51 2. The mini-card will only fit in one direction. Align the small notch in the module with the socket on the connector and insert the card at an angle of approximately 30 degrees into the empty socket. Then press it firmly so that the contact edge is driven into the receiving socket.
- Page 52 Congratulations! You have now completed the wireless mini-card installation. During the next time the system boots to Windows, the system will prompt for driver location. Insert the Factory CD-ROM and point to the directory where the Wireless LAN driver can be found. In addition to installing the driver, you may also need to run a Setup.exe program to install the card’s utility applications before it is fully operational.
-
Page 53: Trouble Shooting
I CHAPTER▼ FIVE TROUBLE SHOOTING In this chapter, you will learn how to solve common hardware and software problems. Your computer has been fully tested and complies with the system specifications before shipping. However, incorrect operations and/or mishandling may cause problems. This chapter provides a reference for identifying and correcting common hardware and software problems that you may encounter. -
Page 54: Audio Problems
Check to see if the problem persists when all the external devices are removed. Check to see that the green light indicator on the AC adapter is lit. Check to see the power cord is properly plugged to the wall outlet and to the computer. -
Page 55: Hard Disk Problems
Sound cannot be recorded - You will need to plug-in an external microphone to the microphone connector to record sound. Double-click the speaker icon on the lower right corner of the taskbar to see if the microphone has been muted. 1. -
Page 56: Optical Drive Problems
optical record-able disk, etc.) or uninstall programs that no longer use. Many browsers store files in the hard drive as a cache to speed up the performance. Check the program’s Online Help for instructions on decreasing the cache size or on removing temporary Internet files. -
Page 57: Display Problems
The disk cannot be ejected - Normally, it takes a few seconds to eject the disk. If the disk cannot be ejected, it may be mechanically jammed. Straighten out a paper clip and insert it to a tiny hole next to the eject button. This should reject the disk tray. If not, return the unit for repair. -
Page 58: Cmos Battery Problem
touch pad while typing or using the touch pad. The built-in keyboard accepts no input - If you are connecting an external keyboard to the system, the built-in keyboard may not work. Try restarting the system. The characters on the screen repeat while I type. You may be holding the keys down too long while you’re typing. -
Page 59: Modem Problems
The memory module may not be installed properly. Go back to Chapter 4 to review the details of this operation. The memory module may be defective. The O/S issues an insufficient memory error message during operation - This is often a software or Windows-related problem. A program is draining the memory resources. -
Page 60: Network Adapter / Ethernet Problems
Try a different receiver number and see if the problem persists. Network Adapter / Ethernet Problems The Ethernet adapter does not work - Go to [Start > Settings > Control Panel > System > Hardware > Device Manager]. Double-click on Network Adapters and check if Realtek RTL8100CL Family Fast Ethernet NIC appears as one of the adapters. -
Page 61: Usb2.0 Problems
Certain programs that are processor-intensive may increase the computer temperature to a degree where the computer automatically slows down its CPU clock to protect itself from thermal damage. The program appears stopped or runs very slowly - Press CTRL+ALT+DEL to see if an application is still responding. -
Page 62: Appendix A Product Specification
APPENDIX▼ A PRODUCT SPECIFICATION ▼ Processor and Core Logic GM965 Merom Dual Core Processor, T7700 2.4G/ T7500 2.2G/T7300 2.0G, FSB 800 MHz, 4MB L2 Cache Merom Dual Core Processor, T7100 1.8G, FSB 800 MHz, 2MB L2 Cache TDP 35W GL960 Intel Celeron M Processor 530 1.73GHz/540 1.86GHz/550 2.0GHz, FSB 533 MHz, 1MB L2 cache. - Page 63 DirectSound 3D, EAX 1.0 & 2.0 compatible A3D, I3DL2 compatible, AC97 V2.3 compatible 7.1 Multi-channel compatible (through S/PDIF) Supports Azalia standard 2 Stereo Speakers ▼ Modem Intel GM965/GL960 integrated Modem Controller with MDC card, Azalia V2.2 Modem support V.92 / V.90 / K56flex for download data speed up to 56Kbps.
- Page 64 ▼ Keyboard & Touch pad 87/86-key QWERTY keyboard with embedded numeric keypad and Windows keys, 19.05mm Pitch Traditional Touch Pad ▼ Express Card (New Card) & Multiple Card Reader O2Micro OZ128(Card Reader) Single Slot, 34mm and 54mm type supported Multimedia Card (MMC), Secure Digital Card (SD), Memory Stick (MS), and MS Pro Card ▼...
- Page 65 ▼ BIOS Phoenix Power On Self Test DRAM auto-detection, auto-sizing L2 Cache auto-detection Hard disk type auto-detection APM 1.2 (Advanced Power Management) & ACPI 2.0 (Advanced Configuration Power Interface) Two Level Password Protections 32bit access, Ultra DMA, PIO5 Mode support Multi-boot capability Compatible with Microsoft Windows 2000 / XP / DOS /Windows Vista premium...
-
Page 66: Appendix B Agency Regulatory Notices
APPENDIX▼ B AGENCY REGULATORY NOTICES Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. - Page 67 Connections to Peripheral Devices Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. Declaration of Conformity This device complies with Part 15( CLASS B)/68 the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 68 ''NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.'' IC ID: 3409A-M30EI0...
- Page 69 Type SJ, and (3) 3-conductor. The cord set must have a rated current capacity of at least 10 A. The attachment plug must be an earth-grounding type with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15 A, 250V) configuration. Japan All components of the cord set (cord, connector, and plug) must bear a `PSE` mark and registration number in accordance with the Japanese...
- Page 70 CAUTION: MODEL L41IIx IS DESIGNED TO USE WITH THE FLLOWING AC ADAPTER MODEL ONLY Manufacture: LI SHIN INTERNATIONAL ENTERPRISE CORP. Model: 0335C2065 (65W) Manufacture: EPSF Model: 10652-A (65W) Telephone lines requirement The appropriate utilization of 26AWG telephone line cord on unit. CAUTION: Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
- Page 71 Herstellers. Laser Safety The optical drive used with this computer is certified as a Class 1 laser device according to the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard and International Standards IEC 825 / IEC 825-1 (EN60825 / EN60825-1). The device is not considered harmful, but the following precautions are recommended: Do not open the unit.
- Page 72 Zum Netzanschlua dieses Gerates ist eine geprufte Leitung zu verwenden. Fur einen Nennstrom bis 6A und einem Gerategewicht groBer 3kg ist eine 2X0.75 mm Leitung nicht leichter als (1)H05VV-F, 3G, 0.75mm conductors einzusetzen. Die Steckdose muB nahe dem Gerat angebracht und leicht zuganglich sein.
Need help?
Do you have a question about the TravelPro Series and is the answer not in the manual?
Questions and answers