Bluetooth Wireless Technology - Pioneer SP-SB03 Operating Instructions Manual

10
English

BlUEtOOth wIrElESS tEChNOlOgY

TEACHING YOUR SPEAKER BASE TO RESPOND
to use your Bluetooth
TO ANOTHER REMOTE CONTROL
with the sp-sB23W speaker Bar system, you must
first pair your device with your speaker Bar.
pairing creates the ability for your Bluetooth
to connect with your speaker Bar wirelessly and
exchange information.
you only have to pair your speaker Bar with your
Bluetooth device one time for this exchange of
®
information to take place.
PAIr AND CONNECt YOUr BlUEtOOth DEVICE
1. Make sure your Bluetooth
Bar are powered on and the Bluetooth
is selected on the speaker bar (Blue light above
Bluetooth logo is solid blue).
®
2. activate the Bluetooth
Your Speaker Base is currently programmed to
Bluetooth source device and check it is actively
®
respond to the remote control that is included with
looking for a Bluetooth
the product. However, we strongly recommend
3. press and hold the Bluetooth
programming the Speaker Base to also respond
the Bluetooth light begins to flash slowly.
®
to your existing remote control using the steps
4. your speaker bar will now appear on your
illustrated below. This will enable you to operate all
Bluetooth source device. select "sp-sB23W" on
®
of your components using a single remote control.
your Bluetooth device to initiate pairing.
®
While programming the Speaker Base, ignore
anything that may be displayed on the TV screen.
5. after a few seconds your speaker Bar will now be
paired with your Bluetooth
Not all remote controls can be used to control the
enjoy music playback wirelessly. note: only one
Speaker Base.
device can be connected to the speaker Bar at
1. Power on the Speaker Base and wait for the
one time.
blue light to become solid.
6. using the included remote for your speaker Bar,
2. Using the Source button, select either Analog or
you can track forward and back, pause and play
Digital Input.
your current track, and turn the volume up and
down.
3. Press and hold the Speaker Base's Bluetooth
Pairing/Learn button until the Bluetooth indicator
flashes. Release the button. The light will now
turn solid blue.
4. Press the button on the Speaker Base that you
would like to teach. The Bluetooth light should
begin to flash slowly.
5. Point the remote control that you want to use for
your Speaker Base and push the corresponding
command button that you chose in Step 4.
6. The Bluetooth light should begin flashing
quickly and the Mode indicator will flash green
if the code was accepted (if the Mode indicator
AUtOmAtIC CONNECtION
flashes red the code was not accepted. Move
any time you want to connect the last paired device
the remote control closer and push the button
and play it through the speaker bar, do the following:
again). Now push your remote's command
1. turn your device's Bluetooth
button again and if the Mode indicator flashes
2. enter Bluetooth source by pressing the Bluetooth
®
green the command is now set.
source button from the remote.
7. Repeat this process for each button you would
NOTE: By default, the last connected Bluetooth
like to teach your Speaker Base.
device will automatically connect if available.
8. To exit the learning mode, press and hold the
Bluetooth Pairing/Learn button on the Sound
hOw tO DISCONNECt wIth A BlUEtOOth DEVICE
Base until the Bluetooth indicator flashes. Then
turn off or disconnect the Bluetooth
release the button. The Bluetooth indicator
Bluetooth device.
®
should turn off.
Not all features are available on all Bluetooth
source devices.
wireless technology device
®
device
®
device and speaker
®
source
®
function on your
®
device.
®
pairing button until
®
device and you can
®
function on.
®
feature on your
®
tEAChINg YOUr SPEAkEr BAr tO rESPOND tO
HOW TO OPTIMIZE THE SOUND
ANOthEr rEmOtE CONtrOl
Once the Speaker Base is connected and powered
PrOgrAmmINg INSTruCTIONS: your speaker bar
up, and an active source is selected, you should
is currently programmed to respond to the remote
hear sound from the Speaker Base. If you don't, turn
control that is included with the product. However, we
up the volume on the Speaker Base using its volume
strongly recommend programming the speaker bar to
control buttons.
also respond to your existing remote control using the
steps illustrated below. this will enable you to operate
If your Speaker Base is connected to your TV
all of your components using a single remote control.
but you're not getting sound from it, there's a
While programming the speaker bar, ignore anything
very good chance your TV is set to use its own
that may be displayed on the tv screen.
internal speakers rather than the Speaker Base. It's
impossible to give specific instructions on how to
Not all remote controls can be used to control the
turn off the speakers for every TV, but here's a way
Speaker Bar.
to do it that covers many of the TVs out there.
1. On your TV remote control, find a Menu or Setup
button.
2. Press this button. You should see an on-screen
menu.
3. Next, look for an option to control audio
functions and select it. The setting to turn off
your TV's internal speakers should be here.
If you can't turn off your TV internal speakers, don't
worry. To enjoy the best performance from your
Speaker Base, you'll want it to play louder than your
1. power on the speaker Bar and wait for the blue TV. Use the following steps to adjust the volume
balance between your TV and the base: light to become solid.
2. using the souRce button select either analog or
1. If necessary, program your base to respond to
digital input.
the Volume Up and Down control commands of
your TV remote.
3. press and hold the speaker Bar's BLuetootH/
paiRing/LeaRning button until the Bluetooth
2. Turn your TV volume all the way down using the
light flashes. Release the button. the light will now
control buttons on your TV.
turn solid blue.
3. Then, using the Volume keys on the front
4. press the button on the speaker Bar that you
panel of your Speaker Base (not the ones
would like to teach, the Bluetooth
on the remote control), set the volume to a
begin to flash slowly.
normal listening level. After you make these
5. point the remote control that you want to use for
adjustments, your Speaker Base should always
your speaker bar and push the corresponding
be louder than your TV speakers. Then use the
command button that you chose in step 4.
TV remote control to adjust the volume as you
normally do.
CUSTOMER SERVICE/TECHNICAL SUPPORT:
For assistance with basic set up, operation, or
troubleshooting, you may contact our customer
service hotline at:
1 (800) 421-1404
Hours: Monday-Friday10:30 am-7:00 pm EST
6. the Bluetooth
and the mode light will flash green if the code
®
was accepted (if the mode light flashes red the
code was not accepted. Move the remote control
®
closer and push the button again). now push your
remote's command button again and if the mode
light flashes green the command is now set.
7. Repeat this process for each button you would like
to teach your speaker bar.
8. to exit the learning mode press and hold the
BLuetootH/paiRing/LeaRn button until the
Bluetooth
®
Bluetooth
®
light should
®
1'- 2'
light should begin flashing quickly
®
flashes. then release the button. the
light is now off.
®