Advertisement
POWER ADAPTER CONNECTION
POWER ADAPTER CONNECTION
1 A Universal AC power adapter; (AC110V / AC220 input, DC9V
.
2 Plug the DC end
.
firmly
into adapter jack of receiver base.
3 Notice: Remove batteries if use AC adapter for extended period.
.
Using 2 Dyna-Mic.01 Wireless Systems at Once
Using 2 Dyna-Mic.01 Wireless Systems at Once
The V2GO Dyna-Mic.01 system can be operated simultaneously
with a second V2GO Dyna-Mic.01 system. To avoid having
the 2 systems interfere with one another, they must be assigned
different frequencies. This is accomplished as follows:
1. Open the battery compartments on both
of the wireless microphones and both of
the receiver bases.
2. Remove the batteries from both of
the receiver bases.
3. Locate the micro switch in the
battery compartment of the
receiver base. It is a silver
rectangular box approximately
5/16 inch wide and 1/4 inch high.
A black tab protrudes from the side of the micro switch.
4.Using a pencil or toothpick,
move the black tab in one
receiver base to A position,
and the other receiver base to
the B position. You have now
designated one receiver base
as System A and the other as
System B.
A
A
B
A
B
A
B
5. Locate the micro switch on each handheld microphone. The
batteries do not need to be removed in the handheld wireless
microphone. The micro switch is located just below the batteries.
6. Using a pencil or toothpick, move the black tab in one handheld
wireless microphone A position, and the other handheld wireless
microphone to B position.
handheld wireless microphone as System A and the other as
System B.
7. Reinsert all batteries paying close attention to each batteries
polarity. Handheld wireless microphone System A will now
communicate with receiver base System A.
8. Handheld wireless microphone System B will now communicate
with receiver base System B.
AC110V
/AC220V
A
B
A
B
A
B
B
A
B
A
B
A
B
You have now designated one
BATTERY CHANGE
1 Push down the case cover's forepart slightly and slide backward
.
to open;
2 Place 2 AA new batteries as instructed on compartment label;
.
3 Close up the cover.
.
1 Tip up to open the cover;
.
2 Place new (2) AAA batteries as instructed on compartment label;
.
3 Close up the cover.
.
TROUBLESHOOTING
Problem
1. Batteries are dead, or are not
Red and/or green LEDs
installed correctly
do not illuminate
2. Power switch(s) are not turned on
1. Wireless microphone is too far from
Green LEDs do not flash
2. In a dual microphone setup, the
in unison
1. Check that the supplied audio cable is
A l l
L E D s
o p e r a t e
correctly but no sound is
2. Make sure that the mute switch is not in
h e a r d f r o m k a r a o k e
player, audio mixer or PA
3. Double check all settings on karaoke
system
Move the Dyna-Mic.01's receiver base
I n t e r f e r e n c e
i s
a w a y f r o m i n t e r f e r e n c e c a u s i n g
i n t r o d u c e d i n t o t h e
sound system whenever
electronic devices such as television
t h e D y n a - M i c . 0 1 i s
monitors or devices containing electric
turned on
motors
While in operation the
Move the handheld microphone closer
Dyna-Mic.01
to the receiver base. See instructions
occasionally "drops out"
for ideal operating range.
1.Move microphone further from
2.Keep 2 handhold microphones at
Hear Static
3 . T a k e o u t t h e m i c r o p h o n e ' s
1.Reset the system by reinstalling
batteries
2.Go to www.v2gotech.com for further
Other unlisted problem
information or call 1-877-566-8246 for
more assistance.
3
Solution
the receiver base
micro switches may not be set
correctly. See instructions for using
2 microphones.
connected correctly
the mute position
player, audio mixer or PA system
receiver base. Keep them at least
2 feet distance apart.
least 2 feet distance apart.
batteries and reinstall them to
reset the system.
Advertisement
