Advertisement
Operation Guide 2615 3015
7. In the number area, use D and B to cycle through numbers and symbols
(hyphen, space) at the cursor position. The characters cycle in the sequence shown
below.
Press D.
x
Press B.
8. When the character you want is at the cursor position, press C to move the cursor
to the right.
9. Repeat steps 7 and 8 until you complete number input.
• You can input up to 12 digits for the number.
10. After inputting your data, press A to store it.
• After data storage is complete, the cursor appears in the name area of the
display, ready for input of a new Telememo record.
11. Input more data (starting from step 3) or press A again to return to the Telememo
record screen (without the cursor).
• The name can show only three characters at a time, so longer text scrolls
continuously from right to left. The last character is indicated by the symbol
To recall Telememo records
In the Telememo Mode, use D (+) and B (–) to scroll through Telememo records on
the display.
• Pressing D while the last Telememo record is on the display or B while the first
record is on the display displays the new data screen.
To edit a Telememo record
1. In the Telememo Mode, use D (+) and B (–) to scroll through the records and
display the one you want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C to move the flashing to the character you want to change.
4. Use D (+) and B (–) to change the character.
5. After making the changes that you want, press A to store them and return to the
Telememo record screen.
To delete a Telememo record
1. In the Telememo Mode, use D (+) and B (–) to scroll through the records and
display the one you want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Hold down D and B at the same time until the watch beeps and
flashing on the display.
• The message
CLR
appears, which indicates that the record is being deleted.
After the record is deleted, the cursor appears on the display, ready for input.
4. Input data or press A to return to the Telememo record screen.
World Time
The World Time Mode shows you the current time in 27
Current time in the
cities (29 time zones) around the world.
zone of the
• The time settings of the Timekeeping Mode and the
selected city code
World Time Mode are independent from each other, so
Timekeeping
you must make separate settings for each.
Mode time
• Whenever you change the time setting for any city in the
World Time Mode, the settings of all other cities are
changed accordingly.
• For full information on city codes, see the "City Code
Table".
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
City Code
GMT differential
To view the time in another city code
In the World Time Mode, press D to scroll through city codes (time zones) to the east
or B to scroll to the west.
To set the World Time
1. In the World Time Mode, use D and B to scroll
through the city code (time zone) and find the one you
want.
2. Hold down A until the DST on/off setting of the world
time starts to flash, which indicates the setting screen.
3. Use C to move the flashing in the sequence shown
below to select other settings.
DST on/off
4.When the setting you want to change is flashing, use B and D to change it as
described below.
Setting
Screen
Press D to toggle between Daylight Saving
DST
Time (ON) and Standard Time (OF).
Use D (+) and B (–) to change the setting.
Hour, Minutes
5.Press A to exit the setting screen.
• When setting the world time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D and B to display the
DST indicator
city code whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down A until the DST on/off setting of the world
time starts to flash, which indicates the setting screen.
3. Press D to toggle Daylight Saving Time (DST
displayed) and Standard Time (DST not displayed).
0 to 9
(space)
after it.
CLR
stops
Hour
Minutes
Button Operation
4. Press A to exit the setting screen.
• Note that you cannot switch between Standard Time and Daylight Saving Time while
GMT
is selected as the city code.
• Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
• The Daylight Saving Time indicator
appears while the GMT differential is on the
display only. It does not appear while the city code is on the display.
• The DST indicator is on the display whenever you display a city code for which
Daylight Saving Time is turned on.
Countdown Timer
You can set the countdown timer within a range of one
minute to 100 hours. An alarm sounds when the
Timekeeping
Mode time
countdown reaches zero.
• You can also select auto-repeat, which automatically
Minutes
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
To set the countdown start time
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the hour
Hours
Seconds
setting of the countdown start time starts to flash, which
indicates the setting screen.
• If the countdown start time is not displayed, use the procedure under "To use the
countdown timer" to display it.
2. Press C to move the flashing in the sequence shown below to select other
settings.
Hours
Minutes
3. While a setting is flashing, use D (+) and B (–) to change it.
• To set the starting value of the countdown time to 100 hours, set 0:00.
• See "To turn auto repeat on and off" below for details on the Auto-repeat setting.
4. Press A to exit the setting screen.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing D), and then
press B. This returns the countdown time to its starting value.
To turn auto-repeat on and off
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
indicates the setting screen.
2. Press C twice to move the flashing to the Auto-repeat
setting.
3. Press D to turn auto-repeat on (
(
not displayed).
4. Press A to exit the setting screen.
• When auto-repeat is turned on, the alarm sounds and countdown starts again
whenever the countdown reaches zero. You can stop the countdown by pressing D,
and manually reset to the countdown start time by pressing B.
• Auto-repeat timing repeats up to seven times.
Alarms
You can set five independent Daily Alarms. When an
Timekeeping
alarm is turned on, the alarm tone sounds when the alarm
Mode time
time is reached. One of the alarms can be configured as a
Alarm time
snooze alarm or a one-time alarm, while the other four are
(Hour : Minutes)
one-time alarms.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are five alarm screens numbered 1 through 5.
The hourly time signal screen is indicated by :00.
• When you enter the Alarm Mode, the screen you were
viewing when you last exited the mode appears first.
• All of the operations in this section are performed in the
Alarm number
Alarm Mode, which you enter by pressing C.
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
x1
:00
• You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2
through 5 can be used as one-time alarms only.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash. This indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Auto-
repeat
displayed) and off
x2
x3
x5
x4
2
Advertisement
