Overview System Features 1. The apparatus is equipped with a graphic LCD screen and 8 control buttons: up, down, left, right, enter, return, zoom in& zoom out. You can operate the system on it without connecting keyboard. 2. RS485 and RS232 input connectors: comply with CS-200 series (RS232 or RS-485 video camera signal output, and CS-200 (2400 baud rate).
Safety Instructions 1. Please read and observe these instructions before installing and using the apparatus. Use only accessories specified by the manufacturer. The manufacturer is not liable for damage caused by the use of non-specified accessories. 3. Install the apparatus and its accessories carefully. Strike and fierce shaking may damage the apparatus.
Operation and Features Front Panel Description ○, Power indicator ○, 24×2 bits LCD screen; shows current settings configuration ○, Camera zoom out and speed adjustment ○, Left, for camera direction and menu selection ○, Down, for camera direction and menu selection ○, ...
Rear Panel Description ¡ õ Power switch ○, DC power input: in+ out-, DC 15V~20V (MAX) ○, USB 2.0: USB port for PC connection ○, Video output 1, for input 1 image ○, Video output 2, for input 2 image ○, ...
Video matrix output 1, output selectable; in override mode, operating camera or adjusting GAIN will automatically switch to the image. Turn On After confirming all the wiring is done, switch on the main controller and the LCD will display following information B X B S D C...
System Operations & Settings Mic Positioning Set auto-track preset points, 128 preset points for each camera and up to 4 cameras the most. Press ▲ or ▼, switch ◘ to Mic Positioning, and then press Enter. ◘ P o s i o n i n g S e t P r e s e t...
Set Preset Set preset points, each camera provides 128 points and cs-200ccdc supplies up to 4 cameras. Press ▲ or ▼, switch ◘ to Set Preset, and then press Enter. P o s i i o n i n g ◘...
Press Enter to save preset point position, and then press ▲ or ▼ to set address no. ▲ ▼ P r e s s c h o o s e C a m e r a P r e s e t N o : 0 0 1 ...
Protocol Setting Set conference main controller type (input) and camera brand (output). Press ▲ or ▼, switch ◘ to Protocol Setting, and press Enter. P r e s e t ◘ P r o t o c o l S e t i n g ...
Video Jump Mode Set Output Main1& Main2 video matrix output Press ▲ or ▼, switch ◘ to Video Jump Mode, and press Enter. ◘ V i d e o J u m p M o d e G a i n S e t i n g ...
Gain Setting Brightness of each camera can be set individually. There is 0, 1, 2, and 3; in total 4 sets of brightness are adjustable. Press ▲ or ▼, switch ◘ to Gain Setting, and press Enter. V i d e o J u m p M o d e ◘...
Reset Settings Reset to factory setting. Press ▲ or ▼, switch ◘ to Reset Settings, and press Enter. ◘ R e s e t S e t i n g s Press ◄ or ► to select items you want to reset. ...
Data Transfer through USB Port Connect graphical control software on PC through USB port, you can have the data you set up on main controller/ software work synchronically. Data transfer rate (from PC to the main controller) S P E E D D O M E S E T U P - >...
Connection CAUTION INPUT RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: . TO PREVENT ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK) . NO USER SERVICEABLE PARTS TO QUALIFIED SERVICE PERSONNEL MADE IN TAIWAN ~ AC FUSE 250V T8A http://www.bxb.com.tw DC FUSE IOIOI 15~20V Spearer...
Page 18
200CCDC control software. Features Save camera preset points; it supports up to 128 points * 4 cameras. Check high-speed dome camera preset point setting. Data transfer from PC to the main controller. Data transfer from main controller to PC.
Page 19
1. Microphone and camera preset point edit 1. Microphone number 2. Camera number 3. Microphone and camera preset point corresponding table 4. Current editing microphone number 5. Previous/next page and upper/ lower items 6. USB connection display 7. Camera preset point address 8.
Page 20
2. Start editing Select Camera number to enter preset points setting.
Page 21
3. Set preset points 1. Select camera number. 2. Tick and it will go to preset point automatically. 3. 128 points for each camera. 4. Camera speed selection 5. Camera directions control 6. Camera zoom in& zoom out 7. Save preset point 8.
Page 22
4. Go to preset points After entering, simply click on the preset points to review if positions are correct.