Summary of Contents for Geeya GeeyaSuperCam Series
- Page 1 Dear users, the configuration for this camera is professional, so please read the user manual carefully before using the camera. Geeya IP Camera GeeyaSuperCam Series 2014-05 V1.0...
- Page 2 Statement If the user manual can not help you to solve the problem, please call our technology center for solutions. We will update the content for the new functions without notice. Notice 1、 Installation Environment Keep away from the places for high-temperature, heat source and direct sunlight. ...
-
Page 3: Table Of Contents
Index 1. PRODUCT INTRODUCTION ...................... 3 1.1. P ......................... 3 RODUCT SUMMARY 2. INSTALLATION GUIDE ....................... 3 2.1. W LAN ....................3 IRED CONNECTION TO 2.2. W LAN ...................... 5 I CONNECTION TO 2.3. C WAN ......................6 ONNECTION TO 3. -
Page 4: Product Introduction
1. Product introduction 1.1. Product summary Thank you for choosing GeeYaSupraCam IP camera. It is very suitable for family, shops, office building and so on. Main features for GeeYaSupraCam IP camera： Support 3 kinds of H.264 video stream and 1 way MJPEG video stream simultaneously, suitable for Local, Internet and Cross-platform view;... - Page 5 Figure 1 Open http://www.szgeeya.cn/IPC by IE browser and enter GeeYaSupraCam series. Double click “SearchTool.exe” as figure 2, please operate as the following steps: Figure 2 Click “Search”（Please make sure your firewall will not block up the item to be searched） Choose a camera;...
-
Page 6: Wifi Connection To Lan
Set the ip address of the ip camera. according to the information in the red frame on the left. The numbers in the red circle should not be the same. The Http port should be a number between 80~65535; Enter user name and password for the device, the default is “admin”... -
Page 7: Connection To Wan
Figure 5 Select ‘On’ and click ‘Search’, and then select wireless router in pop up menu, click ‘OK’ and enter its password, click ‘apply’ to save the wireless settings. And you can click ‘check’ to check if the wireless setting is successful. After setting successfully, please pull out network cable and reboot the camera to use the wireless function. - Page 8 You should connect it to LAN network and do the port forwarding at first, and then connect the LAN network to WAN, connect as figure 6. Figure 6 For example: operation step of port forwarding as figure 7. Figure 7 Please go to the setting interface of Router, and choose “Port Forwarding”;...
-
Page 9: Operation Of Using Ie Browser
you set in figure 2） After finishing the port forwarding, you can use WAN IP address of router and http port of camera to visit the camera by remote computer as figure 6. Notice: because the routers are different, so the interface and setting method of router are also different, how to do the port forwarding for various routers, please refer to the user manual of your router or consult with router manufacturer. - Page 10 Recommend to view by primary stream in LAN, by second stream in WAN and by third stream in mobile phone. You can view the video by four, nine pictures in same screen, but need to set the camera in 3.6.6 multiple setting. PTZ control If the camera supports PTZ function, you can click up, down, left, right arrow to control the camera moving, click...
-
Page 11: Video Setting
3.2. Video setting 3.2.1. Video parameters Figure 10 JPEG stream is for some views by non windows platform, for example, click ‘mobile view’ in first page, it will transmit JPEG stream actually. -
Page 12: Audio Parameters
3.2.2. Audio parameters Figure 11 The camera supports G.711 and G.726 audio encoding format. The sound of the G.711 is better, but it occupies more bandwidth. If you click “On” of the audio capture, so it will transmit audio in corresponding video stream. Please open the audio here, should you hear the sound when clicking audio play button in figure 9. -
Page 13: Web Setting
3.3. Web setting 3.3.1. Basic web setting Figure 13 The cameras support RTSP protocol, if select “on” of “RTSP authority verification”, you need to enter user name and password when invoke video by RTSP protocol. 3.3.2. WIFI setting Please refer to chapter 2.2. 3.3.3. -
Page 14: Onvif Setting
Figure 15 Notice: Using the third party DDNS, if the http port is not 80, the port number should be adding to the domain name with colon. Example: http://mydomain.dyndns.org:81. 3.3.4. ONVIF setting Figure 16 The camera supports ONVIF protocol, so it can be interconnected with other factory camera with ONVIF. -
Page 15: Motion Detection Setting
3.4.2. Motion Detection Setting Figure 18 Please click “apply” after the settings are done, and motion detection takes effect. The higher value, the higher sensitivity. The camera will trigger corresponding alarm when any change occurs in the detection area. 3.4.3 Sound alarm setting 3.4.4. -
Page 16: Alarm Time Setting
3.4.5. Alarm time setting Figure 20 The device will trigger the alarm only during the scheduled time period, you can select the scheduled time according to your request. Example of figure 20, set armed time from Mon 8:30 to 9:30, you only need to click the corresponding time block to set them, the time block will become green when you selected. -
Page 17: Auto Capture Setting
3.5.2. Auto Capture Setting Figure 22 Tick “Save Images to the TF/SD card”, the snap pictures will be stored into SD card during the setting time. 3.5.3. Timer recording Figure 23 Example of figure 23, set recording time from Mon 8:30 to 9:30. Tips:Please insert TF/SD card when the device power off, to avoid damage the TF/SD card or not to read it from the device. -
Page 18: E-Mail Setting
3.5.4. E-mail Setting Figure 24 The SMTP server name: It is mailbox server, for example of SOHU mailbox, it is “smtp.sohu.com”. Please fill all blanks which we filled above in figure 24 as example. Otherwise, the settings will fail. Please click “Test” to test if the E-mail setting is successful. 3.5.5. -
Page 19: Multiple Settings
3) Create sub-category to store the video or pictures. Notice: The password should not be special character; otherwise the camera can’t identify it. 3.5.6. Multiple settings Figure 26 Please set multiple devices here first to view 4 or 9 split screen at chapter 3.1 browse interface. -
Page 20: System Setting
3.6. System setting 3.6.1. Device information Figure 27 SD status shows the free capacity if SD card is installed. Notice: the device supports max 32G SD card. Please format the SD card to FAT32 before use the card on camera. Please check if the SD Card matches the camera or not before purchasing the SD Card. -
Page 21: Initialize Setting
3.6.3. Initialize setting Figure 29 If you click “Confirm” of Backup setting data, the camera will create a file, you can store it to your computer, and you can directly call this file to restore the settings. The function helps to manage the cameras and no need to do all the settings again. The firmware upgrade is for updating system firmware and web UI.