Recording-Related Keys; Auto/Manu. Key; Monitor Key; Rec Mode Key - Kenwood DMF-9020 Instruction Manual

Recording-related keys

AUTO / MANU. key
This key is used to select whether track numbers are to be
marked automatically during recording or they are to be
marked manually during or after recording. The track num-
bers can be used to locate the beginning of a track during
playback or programming tracks.
Select before starting recording.
AUTO/MANU.
(Remote control unit)
L 40 30 18
21
R
PGM SEARCH

MONITOR key

Press to monitor the sound being input from the source while the unit is in stop mode.
When the REC INPUT is DIGITAL, the sampling rate (48 kHz, 44.1 kHz, 32 kHz) of the input digital signal can be displayed by
pressing this key.
Press in stop mode.
Main unit
MONITOR

REC MODE key

The recording-related settings can be adjusted precisely by selecting the proper display modes.
Selecting the setting adjustment mode
1
Switch the REC MODE on.
REC MODE
/CHARAC.
2
Select the setting adjustment mode.
JOG DIAL
4 ¢
DOWN U P
PUSH SET
3
Adjust the setting value.
JOG DIAL
4 ¢
DOWN U P
PUSH SET
To change another setting, press the JOG DIAL (PUSH
SET knob).(This returns to step 2 above.)
15 12 9 7 1 0 OVER ( dB)
5 3 ANALOG DIGITAL
1
MONITOR
MANUAL
Extinguished in "AUTO"
mode, lit in "MANUAL" mode.
Remote control unit
MONITOR
Set the selection. (by
pressing the JOGDIAL).
JOG DIAL
4 ¢
DOWN U P
PUSH SET
Set the selection. (by
pressing the JOGDIAL).
JOG DIAL
4 ¢
DOWN U P
PUSH SET
AUTO
If a no-sound input has lasted for the time set for the AUTO TIME function
during recording, the track number will be incremented automatically by
"1". Usually, use this position for recording. Use this mode when
recording all of the tracks in a CD. When recording music containing a
continuous section with a very low level, for example when recording
classic music, the track number may be incremented by "1" after such
a section. In this case, cancel the track number later. It is recommended
to use the MANUAL mode when recording such a kind of music.
During digital recording of CD, the track number is incremented auto-
matically by "1" according to the data contained in the digital informa-
tion. The no-sound blank is not detected.
When the CD track number is increased during manual search of a CD,
the track number recorded on the MD may sometimes fail to be
incremented.
A no sound track may sometimes created at the moment the played CD
2 3
stops.
32kHz
44.1kHz
48kHz
MANUAL
With this setting, the MD track number is not incremented automatically
during recording. Track numbers can be marked either during editing (by
pressing the EDIT key) or after recording (by executing the TRACK DIVIDE
fl
operation ). Even when "MANUAL" is set, the AUTO CUT and AUTO
PAUSE functions work if the "AUTO CUT" and "REC AUTO PAUSE"
settings are turned on.
This setting is convenient when recording a CD which has been recorded in
live or which contains very low-level sound such as a classical music CD.
PGM SEARCH
Each press switches the mode.
1 REC MODE : off
2 REC MODE : on
The modes are switched by rotating the JOG DIAL.
D. REC LEVEL?
AUTO CUT?
AUTO TIME?
AUTO LEVEL?
FADE TIME?
REC= WRITING? : Setting of the UTOC writing after recording.
÷ Step 3 consists of adjusting the setting of the "Setting adjustment
mode" selected in step 2.
÷ The "D.REC LEVEL" and "FADE TIME" settings are not used during
analog source recording.
÷ To end the setting adjustment, press the REC MODE/CHARAC. key
again.
DMF-9020/MD-2070 (En)
L 40 30 18 15 12 9 7 1 0
21 5 3
R
"MONITOR" and "Sampling rate" litghts up
: Digital recording level setting.
: AUTO CUT on/off selection.
: Setting of the time for detecting a no-sound
blank section during automatic track number
marking.
: Automatic track number marking no-sound
blank detection level and SOUND SYNCHRO
REC, AUTO CUT and REC AUTO PAUSE sound
detection level setting
: Setting of the fading time in fade-in and fade-
out.
23
OVER ( dB)
ANALOG DIGITAL
1 2 3
32kHz
MONITOR
44.1kHz
48kHz