Table of Contents
Advertisement
C
ONGRATULATIONS
Your new TV Monitor/Receiver features a solid state
chassis that is designed to give you many years of
enjoyment. It was thoroughly tested and tuned at the
factory for best performance.
Customer Record
The model and serial number of this product may be
found on the back of the unit. You should note the
model and serial number in the space provided and
retain as a permanent record of your purchase. This
will aid in identification in the event of theft or loss.
Product registration is available for U.S. customers at:
www.prodreg.com/panasonic
Model
Number
Serial
Number
Care and Cleaning
Screen (Turn TV Off)
•
Use a mild soap solution or window
cleaner with a soft clean cloth. DO NOT
USE ABRASIVE CLEANERS.
•
Avoid excessive moisture and wipe dry.
Cabinet and Remote Control
•
Use a soft cloth dampened with water or a
mild detergent solution.
benzene, thinner, or other petroleum
based cleaners.
•
Wipe dry with a soft clean cloth. Avoid
excessive moisture.
Specifications
Power Source
CT-1388YD, CT-1389VYD (0.9A)
CT-2088YD, CT-2089VYD (1.3A)
CT-2788YD, CT-2789VYD (1.8A)
Channel Capability - 181
(CT-1389VYD, CT-2089VYD and
CT-2789VYD only)
1 Video Input Jack
(CT-2788YD and CT-2789VYD)
3 Video Input Jacks
(CT-1388YD,CT-1389VYD.
CT-2088YD and CT-2089VYD)
1 (set) Audio Input Jack
(CT-2788YD and CT-2789VYD)
3 Audio Input Jacks
(CT-1388YD, CT-1389VYD,
CT-2088YD and CT-2089VYD)
1 Video Output Jack
(CT-2788YD and CT-2789VYD)
3 Video Output Jacks
(CT-1388YD, CT-1389VYD,
CT-2088YD and CT-2089VYD)
1 (set) Audio Output Jack
(CT-2788YD and CT-2789VYD)
3 Audio Output Jacks
(CT-1388YD, CT-1389VYD,
CT-2088YD and CT-2089VYD)
Video Monitor Output Jack
Audio Monitor Output Jack
S-Video In/Out Jacks
Earphone Jack
(CT-1388YD and CT-1389VYD)
Specifications are subject to change without notice
or obligation.
Television Location
This unit is intended to be used with an
entertainment center. Consult your dealer for
available options.
Avoid excessive sunlight or bright lights,
including reflections.
Keep away from excessive heat or moisture.
Inadequate ventilation may cause internal
component failure.
Fluorescent lighting may reduce Remote
Control transmitting range.
Avoid magnetic equipment, including motors,
fans, or external speakers.
Optional Cable Connections
Shielded audio and video cables should be used
between components. For best results:
•
Use 75-ohm coaxial shielded cables.
•
Use appropriate input and output
connectors that match your component
connectors.
•
Avoid
interference.
AC Power Supply Cord
CAUTION: MAKE SURE PLUG
IS INSERTED FULLY INTO
RECEPTACLE.
Do not use
This product is equipped with
a three-wire ground type plug -
a plug with two blades and a
third pin which is round. This
plug
will
only
grounding type outlet. This is a safety feature. If you
are unable to insert the plug into the outlet, contact
your electrician to replace your obsolete outlet. DO
120V AC,
60Hz
NOT DEFEAT THE SAFETY PURPOSE OF THE
GROUNDING TYPE PLUG.
VHF-12;
Batteries
UHF-56;
Cable-113
•
Replace batteries in pairs.
•
Do not mix battery types (zinc carbon with
1V
,
p-p
alkaline).
75 Ohm,
•
Do not recharge, short-circuit, disassemble,
BNC Jack
Type
heat, or burn used batteries.
Cable / Antenna
500mV RMS
47K Ohm
For proper reception, either a cable or antenna
Phono Jack
connection are required.
Type
Cable Connection
Connect the cable supplied by your local
BNC Jack
Type
cable company.
Incoming Cable from Cable Company
Phono Jack
Type
BNC Jack
Type
Note:
A cable converter box may be required for
Phono Jack
proper reception. Check with your local
Type
Cable
Y-C
requirements.
Connector
1/8" mini
plug Type
- 3 -
I
NSTALLATION
long
cables
to
minimize
3 Wire Ground plug
fit
into
a
75 Ohms VHF/UHF
on back of TV
company
for
compatibility
Hide quick links:
Advertisement
Table of Contents
