In addition a remote controller which transmits infrared signals (IR) should be used to control the device to get full access to all functions. PicoCombi can be connected to 1 or 2 doorphone outdoor units which are not delivered with the apparatus.
• How to save numbers (up to 50 pcs) in the telephone book are described in chapter 4.2. • To get the most out of all functions in the PicoCombi, the installer should go through all settings and make any changes in the advanced programming mode. This mode are described in chapter 4.3.
3.1 Incoming call PicoCombi gives a ringing signal to indicate an incoming call. You may hook off by the use of the remote controller, key on device, external switch or by the help of the automatic answering function if this is enabled.
3.3 Telephone conversation The telephone line will be active until: • The user disconnects (”hook on”) with the remote controller, key on PicoCombi, or an external switch. • The person you are talking to, hooks on. • If the conversation is started by the automatic answering function, it will be ended when the predefined conversation time (programmable in advanced programming mode) expires.
Open/unlock door (5 seconds active output) and thereafter Door key on device terminate conversation with doorphone. If beeper in doorlock are mounted, the user will normally hear this sound through the doorphone system. PicoCombi loudspeaking analog telephone and doorphone Page 8.
3.5.5 Volume adjustment Volume adjustments for the telephone function on PicoCombi may be adjusted with the remote controller in 5 steps. If the volume has been changed, the new value is stored and used for later telephone conversations. When pressing ”F” on remote controller the volume will increase and it will be indicated by one short ”beep”...
The automatic answering function can be turned on and off with an IR-remote controller or with the ”automatic answering function key” on PicoCombi. The function will be active both for telephone and for the doorphone. A light indicator will illuminate when the function is enabled.
A pause (”F”) can be a part of a number in the telephone book. PicoCombi will wait a predefined time before the numbertransmitting continues if ”F” is a part of the telephone number.
The following accessories are available: • External switches to control telephone line, doorphone and phone book numbers 1-3. • Outdoor units for doorphone. • External IR-sensors. • External loudspeaker. • External microphone. PicoCombi loudspeaking analog telephone and doorphone Page 12.
• Programming – default/recycling: Restore default settings. Observe that: • When installing a PicoCombi you should as a first job enter advanced programming mode and record speech to the auditive feedback (point 31 in the list). This should be done because this feedback will be a very good help in programming mode.
Especially with the built in speech functions which are available. When installing a PicoCombi you should as a first job enter advanced programming mode and record speech to the auditive feedback (point 31 in the list). This should be done because this feedback will be a very good help in programming mode.
Finish the sequence. Start with "0", go on with ”1” and so on. ”Pause” is the last word. Important! • When installing a PicoCombi you should as a first job enter advanced PicoCombi loudspeaking analog telephone and doorphone Page 18.
4.4 Programming – IR-training When entering this mode, then the PicoCombi automatically will activate the trained IR- format, while the other IR-formats will remain unaltered. This means that it is possible to use more than one remote controller to control the device. To enter IR-training mode, only keys on the device shall be used: 1.
4.5 Programming – back to default settings There is a 2-stage process to execute to get the PicoCombi back to default settings. This sequence is controlled by the keys on the device. • Step 1 restores all changeable parametres back to default settings.
• Frontfoil. Productname, light indicators and keys are visually viewed on it. 7.1 Fixed mounting PicoCombi are designed to be placed on a flat surface, or it can be hanged vertically with the help of the built-in screwholes. • Ensure that cables not are crushed between the device and surface.
Controls LED on external IR-sensor(s). IR-signal from external IR-sensor(s). 1 or 2 external IR-sensors (Picomed ES2) can be connected to the terminal strip. They will be supplied with 0 and +12 VDC together with LED signal from the device. The IR-signal wires are also connected at the same terminal strip.
7.2.2 Doorphone A doorphone (outdoor unit) named Picomed EFP can be connected as the table shows on the terminal strips DP1 and DP2 on PicoCombi. DP1 and DP2 are, with exception of connection D.SW at DP1, equal. They have the following connections with recommended colours: PicoCombi loudspeaking analog telephone and doorphone Page 23.
It is possible to have up to 4 PicoCombi' s connected to the same telephone line/doorphone line. If more than one PicoCombi shall be used, use 1 power supply for each, and then connect all wires from one to another in parallell both for telephone and doorphone.
7.4 Default (recycling) The following shall be done on Picomeds PicoCombi when it shall be used by a new user. If neccessary, make a copy of this page, fill inn serial number, version and tick off the points which are done with signature and date at each point, and file it as your routines requires.
Signals, voice messages, telephone numbers and other data will be deleted. Store. 7.5 Technical data Type • Picomed PicoCombi loudspeaking IR-controlled analog telephone and doorphone. Operate • Picomed IR-remote controller with 16 channels. • An other IR-remote controller with 16 channels.