Table of Contents
Advertisement
Quick Links
V3060 Series
Embedded Network Digital Video Recorder
Installation/Operation Instructions
This manual is applicable for the installation and operation of Infinova V3060 series Embedded
Network Digital Video Recorders.
V3060 series DVR employs high performance power PC hardware structure, embedded Linux system
and 1000M network port design to provide an excellent digital product for surveillance industry. This
series DVR supports up to 16-ch video recording and partial channel supports up to 4CIF (D1)
resolution, which can meet the demand of any surveillance system.
Advertisement
Table of Contents
Related Manuals for Infinova V3060 Series
Summary of Contents for Infinova V3060 Series
- Page 1 V3060 Series Embedded Network Digital Video Recorder Installation/Operation Instructions This manual is applicable for the installation and operation of Infinova V3060 series Embedded Network Digital Video Recorders. V3060 series DVR employs high performance power PC hardware structure, embedded Linux system and 1000M network port design to provide an excellent digital product for surveillance industry.
-
Page 2: Copyright Statement
This device must accept any interference received, including interference that may cause undesired operation. V3060 series Network Digital Video Recorders have been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. -
Page 3: Important Safety Instructions And Warnings
Warning: To avoid risk of fire and electric shock, keep indoor products away from rain and moisture! Related Documentations <V3082 Series Client Software for Embedded DVR Manual> <V3060 Series Embedded DVR Quick Operation Guide> <V3060 Series Embedded DVR Quick Installation Manual>... - Page 4 Change the damaged harddisk to insure the integrality of the record data(The information of the harddisk error is in the log) It's better to use the recommended HDDs only. Please visit below link for the list of the HDDs recommended by Infinova:...
-
Page 5: Table Of Contents
Table of Contents 4.4.1 PTZ Parameters Setting..........16 Chapter 1 System Overview ............1 1.1 Product Description .............. 1 4.4.2 PTZ Direction Control ..........16 1.2 Front Panel Introduction ............2 4.4.3 Set and Call Preset............16 1.3 Remote Controller Introduction ..........4 4.4.4 Set and Call Pattern ............. -
Page 7: Chapter 1 System Overview
32-ch video parallel connection. y Provide various abnormity hand modes, support hard disk full, V3060 series DVR can not only work independently in a local site, hard disk error, unauthorized access and network conflict but also build a powerful security surveillance network. This series... -
Page 8: Front Panel Introduction
1.2 Front Panel Introduction Figure 1-1 Front panel Name Type Description Status Channel 1-16 status indication, "Green" indicates recording is ongoing, "red" indicates net 1-16 indicator transfer is ongoing, "orange" indicates both recording and net transfer are ongoing (1) Input message, including numerals, capital & small English letters and symbols etc. Number key (2) Switch channel in preview and PTZ control status. - Page 9 (1) Close iris in PTZ control status IRIS- Control key (2) Quick enter to "PTZ control" mode, the function is same as PTZ key (1) Switch input methods (numeral, letter and symbol) Control key (2) Reduce focus in PTZ control status (3) Set the full screen as setting area in "Mask/Video mask alarm/Motion detection"...
-
Page 10: Remote Controller Introduction
1.3 Remote Controller Introduction Name Full Name Type Description Power Switch Control key Power switch of DVR (Press at least 3 seconds when turn off DVR) Select DVR to be controlled. Use method: DEV key>Device No.> Device Control key ENTER key Number Key Input key The function is the same with the number keys in front panel... - Page 11 FOCUS Focus Control key Increase/Decrease focus in PTZ control Function key The function is the same with F1 key in front panel (1) Switch between preview interface and recording management Video Record Function key interface (2) Call up presets in PTZ control, same as PRST in front panel PLAY Play Video Function key...
-
Page 12: Chapter 2 Installation And Connection
Chapter 2 Installation and Connection Reference: Formula to calculate total capacity needed for DVR Note: Make sure the power supply cable is disconnected before Calculate total capacity needed by each DVR according to video connecting DVR with other device. recording (video recording type and video file storage time). Calculate formula: 2.1 Counter-check Device and Accessories Step: Calculate the capacity... -
Page 13: Rear Panel Introduction
2.3 Rear Panel Introduction VIDEO IN Tested To Comply With AC 100~240V FCC Class B Standard 50/60Hz 70W For Home Or Office Use LOOPING LINE IN RS-422 RELAYS OUT AUDIO IN 1-8 AUDIO IN 9-16 OUT1 OUT2 T- R+R- VIDEO AUDIO LINE OUT ALARMS... -
Page 14: Alarm Input/Output Connection Method Introduction
2.4 Alarm Input/output Connection Method DVR Alarm Output Port AC or DC Load Introduction 1. Alarm input interface introduction Relay 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ALARMS J1400 Figure 2-2 Alarm input interface DC/AC G (GND): 2 "Alarm Input"... -
Page 15: Ethernet Connection Cable Making Method
2.5 Ethernet Connection Cable Making Method 2.6 RS-232 Connection Cable Making Method 1. Material and tool 1. Material and tool A twist cable (8 cores, length depends on the actual demand, but One twisted cable (8 cores), one standard RJ45 connector, one or less than 100m), 2 standard RJ45 connectors, 1 special tool for more DB25 or DB9 plug, a special tool for RJ45, one soldering iron, RJ45. -
Page 16: Install Writer
the following situations and parallelism of pins. (4) When the RJ45 serial port of the DVR is connected with the device with DB9 male type connector, the pin parallelism as follows: DB9 Male Type Serial Port Connection Cable Device RJ45 DB9(Female) DB9(Male) TXD 4... -
Page 17: Chapter 3 System Menu Introduction
This manual mainly focus on the introducing the operation via front panel. 3.1 Menu Operation V3060 series DVR has three levels of menu. The first level of menu is shown in Figure 3-1. Figure 3-3 Every menu has many operations, below section will have detailed introduction on operation of common use control and input method. -
Page 18: List Box
3.1.3 List Box "Select All": Select all available options in current menu. "Unselect All": Cancel the selection of the options in current menu. When there're 2 or more than 2 options, but only 1 option can be "Search": Search the content match with the setting. selected, first press ENT to call out the list box, then select the "Refresh list": Refresh the data in the list. -
Page 19: Menu Structure
Sensitivity Area Schedule Week, Time Recording, PTZ Video control, Figure 3-10 Motion Audible Detection Warning, Linkage Control Center, Alarm Preview and 4 Alarm Outputs Figure 3-11 Copy to Monitor, Open/Close video preview, Note: Preview Switching Time, Open/Close Preview (1) Some editing boxes allow number input only. Alarm Preview, Alarm Preview Switching Time, Preview Mode (2) For the letters combined in one key, press the key one time to... -
Page 20: Chapter 4 Main Functions Introduction
NIC, NIC Type and MAC Chapter 4 Main Functions Introduction Address, IP Type, IP General Address, Subnet Mask, Settings Gateway, Port, Auto DNS 4.1 Turn on DVR Network and DNS Server Note: The DVR supports 100V-240VAC self-adaptive power supply. HTTP Port, SNMP Port, Advanced Alarm Center IP, Remote Before powering on, please confirm the AC voltage matches with... -
Page 21: User Authority
The default administrator user name is "admin" with the password 4.3 Preview as "12345678", and the default langue is English. The DVR's menu divides to parts follows: (1) Preview The operating steps as follows: (2) Manual recording: press REC key to turn on the recording Step: Press ENT key to drop down user name list, move the status list... -
Page 22: Ptz Parameters Setting
For example, the address of the dome camera is 3, baud rate is 2400 and Infinova protocol, the setting of DVR must be same. 4.4.4 Set and Call Pattern Press "Save" after finishing setting, the setting will take effect 1. -
Page 23: Alarm
For example, for the domes key to confirm. After press key , the next box will pop up or pan/tilt cameras with Infinova protocol, the pattern 1 to 4 could automatically, press ESC key to exit and save the setting. - Page 24 (5) Copy and save Refer to "(5) Save" of "Video mask alarm" in section 4.5.1. 3. Motion detection alarm Select channel Refer to "(1) Select channel" of "Video loss alarm" in section 4.5.1. (2) Select the video motion detection check box Move the cursor to the check box of "Video motion detection", and press ENT key.
-
Page 25: Alarm Input
Trigger: Select the corresponding output, press ENT key, the key to drop down the list, and select corresponding alarm type. status becomes "9". The selected output port generates alarm 2. Output setting trigger message when there's motion detection alarm. Move the cursor to the output check box, and press ENT key, the Press "Save"... -
Page 26: Recording
alarm, then the indicator will turn off, and press ENT key to clear 2. Start/Stop manual recording in all channels the alarm in that channel. Move the cursor to "Select All" button, and press ENT key to (2) Clear all alarms select all channels and start the manual recording. -
Page 27: Alarm Recording
button to return to recording setting interface. Press "Save" button to save the settings. 6. Copy After finishing setting, move the cursor to "Copy", and press ENT key to copy the current settings temporarily, then move the cursor to "Save" button, and press key to copy the parameters to other channels. - Page 28 There are 2 modes for the searched file playback: one is to play Button Instruction Button Instruction Button Instruction back multi-channel records synchronously, and the other is to play Pause/Play Stop Rewind 30s back single channel record at a time. Please see details below. Slow Forward Fast motion...
-
Page 29: Power Off
the normal status of the playback, Turn off DVR through front panel or remote controller. 2. Abnormal power off (1) Turn off the switch in rear panel directly. (2) Exit Try to avoid (especially while recording). Press ESC key to exit the "Playback" and return to "Preview" interface after finishing all operations. -
Page 30: Chapter 5 Other Settings
It has 8 options, never, 5s, 10s, 20s, 30s, 1m, 2m and 5m. The Chapter 5 Other Settings operation is the same with monitor. (4) Alarm preview 5.1 Preview Settings It has two options, On and Off, the operation is the same with In the preview interface, press MENU key to enter the interface monitor. -
Page 31: Serial Port Settings
(3) Alarm center General settings The general settings include 10 settings, as follows: This setting is to set the IP address of alarm center. When the cursor moves to this filed, and press ENT key, and the editing box NIC type becomes input status, and input related value, and press ENT key. -
Page 32: User Management
Data bits interface. Move the cursor to select the privilege needs to be added Stop bits or cancelled, and press ENT key to check or cancel the checkbox Parity to add or cancel the privilege. Flow control (3) Add user Add user operation includes 3 parts, user name, password and The introduction of each option as follows: confirm password. -
Page 33: System Settings
1. Time zone: Set the time zone as actual demand. The device name supports 1 to 20 characters string. The default 2. Local time: Set the local date and time. name is "Infinova DVR". 3. NTP: Move the cursor to the checkbox of "NTP Enable", and press... -
Page 34: Log Management
of "Server IP", and input IP address. "Enable NTP server enter the setting interface, and press WIDE key to switch to successfully" prompt appears if the setting succeeds, the system "HD" option, as shown in Figure 5-14. time will keep synchronized with the NTP server. If the setting fails, "Enable NTP server fail"... -
Page 35: Advanced Settings
"Start time" to "End time" to backup. (2). Backup recording file to writer. 3. Record type: backup the specific type of data, 3 types are Note: Make sure the writer has been installed and the disk is placed optional, scheduled, manual and alarm recording. The default is in writer before backup. -
Page 36: General Channel Settings
While the screen shows the main interface, press MENU key to enter interface as shown in Figure 5-1. Select "Channel" and press ENT key or just press 1 key when at Figure 5-1 to enter the channel setting interface, as shown in Figure 5-19. Users can make basic settings of selected channels, including privacy mask, contrast ratio, brightness, hue, saturation, channel name and OSD information. - Page 37 3. Click "¥"on "Playback" in the "Adjust Volume for"; click "OK" 5. Click "OK" to return the recording dialog box, shown in the to return the volume control dialog box in the following figure: following figure: Figure 5-22 Figure 5-24 4.
- Page 38 Infinova 51 Stouts Lane, Monmouth Junction, NJ 08852, U.S.A. Tel: 1-888-685-2002 (USA only) 1-732-355-9100 Fax: 1-732-355-9101 sales@infinova.com V1.1 1312...
Need help?
Do you have a question about the V3060 Series and is the answer not in the manual?
Questions and answers