Icom IC-4SA Upgrade Functions page 3

O S E L E C T I N G A M E M O R Y C H A N N E L
OPush lTlMl.
@ Rotate the tuning control.
nnode )
P R I V A T E
a nd
i
hold p'@
I SCAN TYPES
PROGRAMMED
MEMORY
I SCAN OPERATION
1 ) S e l e c t m :
- Push and hold tmld
for 2sec.
- Push n-l until ffifl appears.
- push [FUNcl.
2) Push I vzttltl to select the operating
mode, VFO or MEI\4ORY.
- Programmed scan : VFO mode.
- Memory scan
: MEMORY mode.
3) Set ISQL] to the threshold point.
4) Push E to start scan.
5) Push E again to stop scan.
<,--.> fnv
fo oP
O M A N U A L S C A N R E S U M E A N D S C A N D I R E C T I O N
While scan pauses, the tuning control resumes the scan
regardless of the scan resume condition, resume/timer. While
the scan is operating, the tuning control changes the scan
direction.
t :
L . , :
a . : .
1i'' '
' i ' : :
,';
.#i
3) Push [FUrrrE then push E
memory channel.
4) To erase "SKIP,'' repeat step
to write "s KlP" into
3 again.
fifl
I
m€m€m
\
@ pusfr V7Mj. I
/
F o r b l a n k c h a n n e t s e l e c t i o n , p u s h E E
b e f o r e s t e p @
O T R A N S F E R R I N G M E M O R Y C O N T E N T S
C s e f e c t t h e m e m o r y c h a n n e t .
@ P u s h t t r u x c l t h e n p u s h
m€m
*it'iS;,
conYEttEtT-
A memory channel number can be selected in VFO mode
using the dial select function. This function performs quick
memory writings.
O M E M O R Y T R A N S F E R
Memory channels 0 ,', 9 can independently program offset:
frequencies and optional subaudible tone frequencies. I his,
means you can easily select these frequencies in the VFO
using the memory transfer function, even when the trans-
c e i v e r i s r e t u r n e d t o S I M P L E m o d e .
O M E M O R Y C H A N N E L M A S K I N G
ffi*;';ffiffi
lll
W h e n t h e g u i d e a p p e a r s .
Unwanted memory channels can be masked (triOOen). A
masked memory channel cannot be selected for normal use.
However, the contents can be revived. The masked rilemo[]
c a n b e r e v i v e d o n l y i n M U L T I - F U N C T I O N m o d e .
r
I
1
l r
The handheld includes both programmed scan and memory
scan. The following initialized setting can be performed
w h e n i n M U L T I - F U N C T I O N m o d e :
- Programmed scan edges {using SET mode)
- Frequency skip function on/off (using PRIVATE
- Memory skip function (when
ffi
appears.)
- Scan resume condition, pause/timer (using
mode)
A p p e a r s w h e n i n
M E M O R Y m o d e .
I T R E Q U E N C Y S K I P & M E M O R Y S K | P
The frequency skip function can be activated during pro-
grammed scan. The function skips unwanted signals that
inconveniently stop scanning such as no modulation signals.
The memory skip function skips unnecessary memory
channels during memory scan, making shorter intervals for
memory scanning.
SKIP
r S K I P C H A N N E L P R O G R A M M I N G
O F R E Q U E N C Y S K I P
While scan pauses, push ITUN-el then push and hold IVTltltl 1s
program the frequency as the skip channel.
To cancel the program, see the memory skip function below
since the skip frequencies has been autorn atically program-
med into memory channels 47 ,^-, 10 the same as the memory
s k i p c h a n n e l .
E M E M O R Y S K I P
1) Select the memory channel to be programmed.
2) Select ffi:
- Push and hold tFtiMCl for 2 sec.
- Push [-d until ffi
appears.
- Push ITuNCl.
tY5.6 il
."r.
t h e