Page 1
F R E E S T A N D I N G WOOD STOVES Limit 380 INSTALLATION MANUAL Firepoint 360 This manual includes instructions for the Installation, Operation and Maintenance of your stove. Models Limit 380 Firepoint 360 Spirit 550 Please read this entire manual carefully before installing and lighting your stove.
INSTALLATION How do I remove the ash from my stove? What is the most adequate location to install my Bosca stove? How do I clean the glass panel on my stove? What is the correct way to install my Bosca stove?
INSTALLATION MANUAL MAIN COMPONENTS WARNING: THIS APPLIANCE AND FLUE SYSTEM SHALL BE INSTALLED IN ACCORDANCE WITH AS/NZS 2918 AND THE APPROPRIATE REQUIREMENTS OF THE RELEVANT BUILDING CODE OR CODES. Flue Spigot WARNING: APPLIANCES INSTALLED IN ACCORDANCE WITH THIS STANDARD SHALL COMPLY WITH THE REQUIREMENTS Ceramic Glass (Resists temperatures up to 800ºC) OF AS/NZS 4013 WHERE REQUIRED BY THE REGULATORY AUTHORITY, I.E.
For clearances to non-combustIble or insulated walls refer to AS/NZS 2918 Note: For Spirit 550 & Limit 380, side clearance (B) to be no less than 200mm and rear To ensure the safe and proper functioning of your stove, it must be installed according to the clearance (A) no less than 100mm irrespective of wall material, to ensure access to rear of instructions included in this manual.
This can be acheived in the Limit 380 and Firepoint 360 by using the two holes provided in the baseplate of the fireplace and using masonary anchors if installing onto a concrete floor, FLOOR PROTECTOR or any suitable fastener for wooden floors.
INSTRUCTIONS FOR REPLACING THE BAFFLE SPIRIT 500 / 550 LIMIT 380 1. The first stage consists of 4. To remove the baffle, 1. The Spirit model stove removing the anchoring hold it with both hands has a dismountable back 11 mm spanner 11 mm spanner bolts of the baffle.
Page 7
INSTRUCTIONS FOR REPLACING THE BAFFLE SPIRIT 500 / 550 (continued) FIREPOINT 360 / 400 4. To remove the baffle, 1. The first stage consists of 4. To remove the baffle, hold hold it with both hands removing the anchoring it with both hands and slide 11 mm spanner and slide it forward so that bolts of the baffle.
OPERATING INSTRUCTIONS How can I verify that the installation has been correctly executed? OPERATING INSTRUCTIONS We are aware of how important it is to you to feel confident that your stove has been properly installed. Therefore, if you wish to verify the installation, we recommend you use the following How does the double combustion system work? diagram to guide your inspection: Double combustion stoves have a secondary air inlet that preheats the air at a high temperature.
OPERATING INSTRUCTIONS your efforts will have been wasted. This is why it is important that you safeguard the storage 4. Light the fire and close the upper door of the conditions. The wood must be stored in an isolated location so that it is not exposed to rain and stove.
"maximum" and open the door of the firebox (upper door). What maintenance does my Bosca stove require? 2. Place the dry firewood logs on the cinders Cleaning the flues is essential to ensure the proper functioning of your stove. This consists of inside the stove.Logs must be loaded front to...
IMPORTANT Bosca stoves contain a baffle that must be dismounted in order to clean the unit. 3. Remove the anchoring screws to dismount 6. Pull the rope inside the stove so that the the baffle of your stove.
How can I avoid a chimney fire? One of the appeals of your Bosca stove is the visible fire. However, often this is limited because of spots that appear on the glass of the stove. To avoid this follow the instructions below: - The key to avoiding a chimney fire is to keep your stove’s gas exhaust system clean.
Your Bosca stove is identified by a serial number stamped on a plate on the inside of the Air Control completely. Do not burn large ashtray door. No other Bosca stove of similar model has the same serial number, which may be amounts of paper or requested if you require a service.
- Bosca wood fires are painted with high temperature porous paint that will show signs of surface rust if exposed to moisture for an extended periodof time.
Need help?
Do you have a question about the Limit 380 and is the answer not in the manual?
Questions and answers