Table of Contents
Advertisement
SECTION
5
SERVICE
mECH.
INFORMATION
A. TROUBLESHOOTING
NEUTRAUZER
FILTER
FILTERED
WATER IS ACID
(LOW pH)
TASTE & ODOR RLTER
FILTERED WATER bIAS TASTE
AND/OR ODOR
NEEDS REFILL OF
i
I
NEEDS REPLACEMENT
NEUTRALITE
M INERAL
OF ACTIVATED
CARBON
MINERAL
ALL FILTERS
I
FILTEREDWATER CONTAINS SEDIMENTS,
(SAND, StLT,,DIRT, ETC.) OR IRON
!
I
IRON IN WATERREQU IRES
I
OTHER WATERCONDITIONING
(HAVE WATERANALYZED)
1
V,SUA OHEO S
1. Is raw water pipe plumbed to valve inlet?
i Is plumbing bypass valve(s) in service?
Is valve drainhose unobstructed?
TIMER SHOWSWRONGTIME
I
AND DAY AND/0B S FLASH NG I
=
Electrical power was off.
I
i
Reset all timer programming
I
Investigatereason for
powerloss. Be sure out-
let for filter cannot be
switched off.
J Do ManualAdvance
I
Diagnosticto verify pro-
per function.
f
f
f
PROGRAMMINGOK
I TOO FEW BACK-
i
FOR FAMILY NEEDS
I WASHES PRO-
GRAMMED.
1. Leaking faucet or
REPROGRAM _
Do ManualAdvanceDiagnostic to
l
stool
I
_
ver fy proper function.
I
2. Filteredwater usebl
at o utaide
faucets
LI DO MANUAL
ADVANCE
TO I
/
3. Otherunusual fil- r,P-i FILL CYCLE- CHECK FILL
tered waterusage/I
FLOWTO SOLUTON B0rFLE
/
/
TIMER DISPLAY SHOWS CORRECT
TIME AND DAY, AND IS STEADY
i
OBSERVEVALVE CAM POSITION
l
I'N ERV, E
PDS,,,ON
I
[ OT IN SERV,OE
POSITIO
I
TEST WATERAT FILTERED WATER /
1. Wiring harness has loose
FAUCETCLOSEST TO FILTER
J
connections,
or defective
t
2. Switch defective
_
3. Valve motor inoperative
t NOSED'MENTS 1
WATER CONTAIN 4
IN WATER
I
SEDIMENTS 1
I CHECK
PROGRAMMING
I
Filterregeneratedsince
customer railed. Checkfor
correct regenerationpro-
gramming.
f
[ Do Manual Advance Diagnostic I
to verify proper function.
/
/
/
[TIMER
DISPLAY
DLANK
I
÷
Check electrical
power
to timer (outlet, trans-
former, all connections)
t
I POWER
OKAY
I
FACE PLATE
DEFECTVE
/
/
/
FACEPLATE
REPLACEMENT:
BE SURE
THE
VALVE
IS IN SERVICE
POSITION
(OBSERVE
VALVE
CYCLE
INDICATOR)
WHEN
REPLACING
THE FACEPLATE.
If after installing
and programming
the replacement
faceplate,
the valve is not in
M
service
position,
do the following
to assure
correct
cycle orientation,
or timing,
between
the faceplate
and valve.
S •
(SERVICE)
Use the MANUAL
ADVANCE
procedures,
page 5- 3. With the the RECHARGE
button,
advance
through
the recharge
cycles until the valve stops
in service
posi-
tion, and RECHARGE
no longer
flashes
in the timer.
Valve
Cam
NOTE:
The valve motor
may automatically
drive
through
several
valve positions
while
searching
for service.
5-4
Valve
Position
Indicator
Problems,
Questions?
Call 1-800-426-9345
Kenmore
Water Line
Advertisement
Table of Contents
