Kenwood TK-7180 Service Manual Addendum page 13

■ Frequency and Signaling
The transceiver has been adjusted for the frequencies
shown in the following table. When required, readjust them
following the adjustment procedure to obtain the frequencies
you want in actual operation.
• Test frequency
136~174MHz (TK-7180 K,E/7189 E)
CH RX (MHz)
1 155.05000
2 136.05000
3 173.95000
4 155.00000
5 155.20000
6 155.40000
7 177.95000
8~16 -
450~520MHz (TK-8180 K)
CH RX (MHz)
1 485.05000
2 450.05000
3 519.95000
4 485.00000
5 485.20000
6 485.40000
7~16 -
400~470MHz (TK-8180 K2,E/TK-8189 E)
CH RX (MHz)
1 435.05000
2 400.05000
3 469.95000
4 435.00000
5 435.20000
6 435.40000
7~16 -
ADJUSTMENT
TX (MHz)
155.10000
136.10000
173.90000
155.00000
155.20000
155.40000
177.90000
-
TX (MHz)
485.10000
450.10000
519.90000
485.00000
485.20000
485.40000
-
TX (MHz)
435.10000
400.10000
469.90000
435.00000
435.20000
435.40000
-
TK-7180/7189/8180/8189
• Test signaling
No. RX
1 None
2 None
3 Skip
4 QT : 67.0Hz
5 QT : 151.4Hz
6 QT : 210.7Hz
7 QT : 254.1Hz
8 DQT : D023N
9 DQT : D754I
10 Skip
11 None
12 Skip
13 Skip
14 None
15 Skip
16 None
17 MSK :
Preamble : 0xAAAA
Sync : 0x23EB
Data : 0x230960C6AAAA
CRC : 0xC4D7
Panel Tuning Mode
■ Preparations for tuning the transceiver
Before attempting to tune the transceiver, connect the
unit to a suitable power supply.
Whenever the transmitter is turned, the unit must be con-
nected to a suitable dummy load (i.e. power meter).
The speaker output connector must be terminated with a
4Ω dummy load and connected to an AC voltmeter and an
audio distortion meter or a SINAD measurement meter at all
times during tuning.
■ Transceiver tuning
(To place transceiver in tuning mode)
Press [S] key, now in tuning mode. Use [B] key to write
tuning data through tuning modes, and [ ]/[ ] to adjust tun-
ing requirements (1 to 256 appears on LCD).
Use [C] key to select the adjustment item through tuning
modes. Use [A] key to adjust 3 or 5 reference level adjust-
ments, and use [■ ] key to switch between Wide/Narrow.
Channel appears on LCD. Set channel according to tuning
requirements.
• LCD display in panel tuning mode
n B A L
n : Narrow
Adjustment item
w : Wide
TX
None
100Hz Square Wave
QT : 67.0Hz
QT : 151.4Hz
QT : 210.7Hz
QT : 254.1Hz
DQT : D023N
DQT : D754I
DTMF Code 9
Single Tone : 1000Hz
MSK
MSK :
Preamble : 0xAAAA
Sync : 0x23EB
Data : 0x230960C6AAAA
CRC : 0xC4D7
2 5 6
Adjustment value (1~256)
13