Table of Contents
Advertisement
Quick Links
WARRANTY
The Gentec-EO UNO Single Channel Laser Power Meter comes with a one-year warranty (from date of
shipment) against material and/or workmanship defects, when used under normal operating conditions.
The warranty does not cover damages related to battery leakage or misuse.
Gentec-EO Inc. will repair or replace, optionally, any UNO that proves to be defective during the warranty
period, except in the case of product misuse.
Any attempt by an unauthorized person to alter or repair the product voids the warranty.
The manufacturer is not liable for consequential damages of any kind.
Customers must fill in and mail the warranty card in order to activate the warranty.
In case of malfunction, contact your local Gentec-EO distributor or nearest Gentec-EO Inc. office to obtain
a return authorization number. The material should be returned to:
Gentec Electro-Optics, Inc.
445, St-Jean-Baptiste, Suite 160
Québec, QC
Canada G2E 5N7
Tel: (418) 651-8003
Fax: (418) 651-1174
e-mail: info@gentec-eo.com
Website: www.gentec-eo.com
CLAIMS
To obtain warranty service, contact your nearest Gentec-EO agent or send the product, with a description
of the problem, prepaid shipping and insurance, to the nearest Gentec-EO agent. Gentec-EO Inc.
assumes no risk for damage in transit. Gentec-EO Inc. will, at its option, repair or replace the defective
product free of charge or refund your purchase price. However, if Gentec-EO Inc. deems that the failure
is caused by misuse, alterations, accident or abnormal condition of operation or handling, you will be billed
for the repair and the repaired product will be returned to you (repetitive, see above).
Advertisement
Table of Contents
Related Manuals for Gentec-EO Uno
Summary of Contents for Gentec-EO Uno
- Page 1 The warranty does not cover damages related to battery leakage or misuse. Gentec-EO Inc. will repair or replace, optionally, any UNO that proves to be defective during the warranty period, except in the case of product misuse.
- Page 2 (from date of shipment) against material and/or workmanship defects, when used under normal operating conditions. The warranty does not cover damages related to battery leakage or misuse. Gentec-EO Inc. will repair or replace, optionally, any UNO that proves to be defective during the warranty period, except in the case of product misuse.
- Page 3 Revision – 6 SAFETY INFORMATION Do not use the UNO if the device or the detector looks damaged, or if you suspect that the UNO is not operating properly. Appropriate installation must be done for water-cooled and fan-cooled detectors. Refer to the specific instructions for more information.
-
Page 4: Table Of Contents
..............................12 EPARATION ........................... 12 ISMANTLING PROCEDURE LIST OF ILLUSTRATIONS . 1-1 UNO F .......................... 6 RONT ANEL . 1-2 UNO C .......................... 7 ONNECTORS . 1-3 UNO LCD D ........................... 9 ISPLAY Gentec Electro – Optics, Inc. All rights reserved... -
Page 5: Introduction
THE UNO SINGLE CHANNEL LASER POWER METER 1.1 Introduction To obtain full performance from the UNO, we recommend that you read this manual carefully. The UNO is a large display laser power monitor that features outstanding efficiency, ease of use and battery life. Unpacking Each Gentec-EO UNO is thoroughly tested and calibrated prior to shipment. -
Page 6: Specifications
The following specifications are based on a one-year calibration cycle, an operating temperature of 18 to 28ºC (64 to 82ºF) and a relative humidity not exceeding 80%. Table 1-1 List of Specifications UNO POWER METER SPECIFICATIONS 10 nW to 10 kW Power Range... -
Page 7: Front Panel Description
9). The hidden dBm function is available by pressing more than 2 seconds on the Zero control key.The Uno will convert the displayed number in dBm (dB referenced to 1mW) and will display “dBm” unit. To get back to the previous display in Watt, press again more than 2 seconds on the Zero control key. -
Page 8: Connector Description
This section contains important information concerning the installation and operation of the UNO. The UNO is delivered ready to use. Just install the 4 AA batteries, insert a detector head in the Probe Input Jack (#2 in Figure 1-2) and press the I/O key. - Page 9 Block off laser radiation to the detector. The power read by the UNO when no laser beam is incident on the detector may not be exactly zero. This is because the detector is not thermally stabilized OR there was a heat source in the detector’s field of view when you turned on the UNO, OR from the internal electronic offset...
-
Page 10: Display Description
The LCD provides measurement information, wavelength information, attenuator selection and other useful messages. When the batteries are discharged enough to compromise the measurement, the UNO displays “LO” instead of the measurement. Refer to the battery maintenance section to replace the batteries. -
Page 11: Battery Selection
- Open and remove the battery door. - Hold down the UNO and slowly pull on the nylon strap to remove the batteries. Do not use a pointed tool to remove the batteries, since that could puncture them. The batteries need a firm pull to be removed in order to have a reliable contact. -
Page 12: Declaration Of Conformity
UNO User’s Manual Revision – 6 DECLARATION OF CONFORMITY Application of Council Directive(s): 2004/108/EC EMC Directive Manufacturer’s Name: Gentec Electro Optics, Inc. Manufacturer’s Address: 445 St-Jean Baptiste, suite 160 Québec (Québec), Canada G2E 5N7 European Representative’s Name: Laser Components S.A.S. -
Page 13: Recycling And Separation Procedure
4.1 Recycling and separation procedure This section is used by the recycling center when the monitor reaches its end of life. Breaking the calibration seal or opening the monitor will void the UNO warranty. The complete Monitor contains 1 Monitor...
Need help?
Do you have a question about the Uno and is the answer not in the manual?
Questions and answers