TiVo DVR Start Here

Start Here

Follow these easy steps to connect your
®
TiVo HD Digital Video Recorder

Connecting Your TiVo HD Digital Video Recorder

Order CableCARD decoders from
your cable company
CableCARD decoders allow the TiVo HD DVR to receive digital cable
channels without a cable box. They plug into the CableCARD slots on the
front of the DVR.
If you subscribe to digital cable, you must order at least one
CableCARD decoder from your cable company.
To watch and record two channels at the same time, you need
either one Multi-Stream CableCARD decoder
or two Single-Stream CableCARD decoders.
Connect your TiVo HD DVR as shown and complete on-screen Guided
Setup before CableCARD installation.
µ
Tune your TV to see
the Welcome Screen
Turn on your TV.
If you don't see
the Welcome screen:
Use the Input, Source, or TV/Video
button on your TV remote or TV
to select the audio/video input source you used in steps
you can also change the channel to select different input sources. Then press the
FORMAT button on the DVR's front panel until you see video.
When you see the Welcome screen, you're ready to begin
We recommended that you complete Guided Setup a few days before CableCARD
installation to ensure that the DVR receives any recent software updates.
To optimize the TiVo HD DVR for high-definition viewing, read
Viewer's Guide
Understanding HDTV in the
To learn more about the amazing, smart-recording features of the
TiVo service, take the Tours in Chapter 1 of the

Plug in the Power Cord

The TiVo DVR's front panel
displays a green light at startup.
®
Connect to the TiVo service: Network OR
The TiVo DVR needs to connect to the TiVo service to receive program listings, service updates, and other
information. Network-connected DVRs also have access to additional features and services. See Chapter 4 in
the Viewer's Guide for details. Choose how your DVR will connect:
Network
If you have a home network with a broadband Internet connection, use the connection that
works with your type of home network:
Phone Line
Choose this option if you don't have a home network with a
broadband Internet connection. Connect the provided
phone cord from the DVR to a nearby wall jack.
SDOC-00107-001 Rev A2
Get to know your cables
M-CARD
HD Video
CableCARD
TM
You must use a high-definition
cable to see high-definition video.
Component Video
cable for high-definition
video (no audio)
Other Connectors
(M-CARD),
TiVo
DVR
and . On many TVs,
Guided Setup.
.
Viewer's Guide
.
Phone Line
Network or Phone Line
Wireless or Wired (Ethernet)
– Connect the TiVo Wireless G USB Network
Wireless
Adapter
(sold separately) to one of the DVR's
USB ports . The TiVo ® Wireless G USB Network Adapter
pictured here is available at www.tivo.com/store.
OR
Wired (Ethernet)
– Connect an Ethernet cable (sold
separately) from your home network to the TiVo DVR's
Ethernet jack (the upper jack pictured here).
Welcome!
Setting up your TiVo ® HD Digital Video Recorder (DVR) is easy.
®
Activate the TiVo
The TiVo service is what makes your DVR smart. It includes everything from your program listings to
TM
Season Pass recordings and WishList
Some TiVo DVRs are sold with a TiVo service plan. If yours was not, activate the TiVo service at
or call TiVo Customer Support at 1-877-367-8486. You'll need your 15-digit TiVo Service Number, found on the label on the
back of the DVR. Write it here for reference ___________________________.
Now, let's get started with Connecting Your TiVo HD Digital Video Recorder! First, a few questions:
Do I need a CableCARD
If you subscribe to digital cable, the answer is
The TiVo HD DVR does not support a connection to an external cable box. To receive digital cable channels, you need at least
one CableCARD decoder. To watch and record two channels at the same time, you need either
CableCARD decoder

How do I get CableCARD decoders?

You can only get CableCARD decoders from your cable company, typically delivered by an installer.
company
to order either one Multi-Stream CableCARD decoder, or two Single-Stream CableCARD decoders.
Locate the sheet titled
the installer upon arrival. This sheet also has instructions for you, after the installer leaves.
Stereo Audio
Use this cable for your audio
connection only.
Composite A/V cable for
stereo audio (red & white
ends) & standard video
(yellow end — don't use)
Phone cord Power cord
®
Television

Connect Video

Connect the Component Video cable (green, blue, red) from the
COMPONENT OUT
TiVo DVR's jack to the
jack on the back of your high-definition TV.
Be sure to use the same TV input for video as you used for
audio in step . Most TVs have more than one input. Make
note of the input you use.
HDMI
Alternate: If your TV has an jack, use an HDMI cable
(sold separately) to connect digital video and digital audio.
© 2007 TiVo Inc. All rights reserved. Reproduction in whole or in part without written permission is prohibited. TiVo, the
TiVo logo, Season Pass, and WishList are trademarks or registered trademarks of TiVo Inc. or its subsidiaries, 2160 Gold
Street, P.O. Box 2160, Alviso, CA 95002-2160. All other trademarks are the properties of their respective owners.
Start Here
service (if you haven't already)
®
searches—all the cool features you've heard about.
TM decoder?
YES
.
two Single-Stream CableCARD decoders
, or
Instructions for CableCARD Installers
, included in the DVR carton. Give these instructions to
(Optional) Connect an
Antenna
Local TV stations broadcast
high-definition signals over
the air on dedicated digital
channels.
To receive both digital (ATSC)
and standard (NTSC)
channels over the air,
connect an indoor or outdoor
antenna to the TiVo DVR's
ANTENNA IN jack.

Connect Audio

Connect the red and white ends of the Composite A/V cable from the
TiVo DVR's A/V OUT jacks to the
connect the yellow end (standard video).
Most TVs have more than one input. Make note of the input you use
for audio, and use the same input when you connect video in step
Alternate: Connect an Optical Digital Audio cable (sold separately)
DIGITAL AUDIO
from the TiVo DVR's
theater system for digital sound.
COMPONENT IN
Check out the Troubleshooting chapter in the Viewer's Guide for
more help with connecting your TiVo DVR, completing Guided Setup,
and using the TiVo service. If you have more questions, visit us online.
Remember:
Connect all cables from the OUT jack
of one device to the IN jack of the next.
OUT
www.tivo.com/activate
M-CARD
CableCARD
TM
one Multi-Stream
.
Call your cable
Disconnect Your Digital Cable Box
If you don't have a cable box, skip to step .
CableCARD decoders replace your digital cable
box. Disconnect your cable box from your TV and
set it aside.
NOTE: While you're waiting for CableCARD
installation, you may want to connect your
cable box to another input on your TV so you
don't miss any of your favorite shows.

Connect to Your Cable Service

Connect the Coaxial RF cable coming out of the
CABLE IN
wall directly to the jack on the back of
the DVR. This cable is probably connected to
your TV or cable box; connect it to the TiVo
DVR instead.
NOTE: If you have a cable box, you may want
to leave this cable connected to the cable box
while you're waiting for CableCARD
installation. See the NOTE in step .
A/V IN jacks on your TV. Do not
.
jack to an A/V receiver or home
Need some help?
www.tivo.com/support
Never connect OUT to OUT or IN to IN.
OUT OUT
IN