Advertisement
Quick Links
Opal RFX Wireless
GJD018 35m External PIR
Installation Manual
OPAL RFX WIRELESS PIR (GJD018)
SUPPLY:
2 x AAA Alkaline 1.5 volt (not supplied)
Low power typical battery life two years
TRANSMISSION - 150m line of sight:
433.92 MHz frequency - SAW stabilised
COVERAGE RANGE 10 to 35m:
35 x 30m max. with 90º multifunction lens
Internal adjustment 180º pan + 90º tilt
MOUNTING HEIGHTS: (variable)
3m high for multi-beam coverage
6m high for curtain coverage and 1.5 for pet
immunity (mask supplied)
PROCESSING - Non-volatile memory:
Intelligent signal processing:
Digital & integral white light filter
16 million possible identification codes
ADJUSTMENTS:
Detection signal (CCTV) timer 0.4 to 60 secs.
Light level signal 2 Lux to daylight
Pulse count 1 (2 & 3≤6 seconds)
TEMPERATURE: -20º C +55º C
DETECTOR HOUSING:
ABS high impact IP55 rated
Weight - 152g
Dimensions 110h x 100w x 100 deep
The wireless Opal RFX external passive infrared intruder detector
design to detect and transmit reliable event based triggers to the
weatherproof RFX-3 Receiver. These combined units enable the
simultaneous or individual control of cameras, VCR's, DVR's and
virtually all low-voltage switching requirements.
The weatherproof receiver with front and rear tamper output can
be positioned in line of sight up to 150m away. The active state of
up to 3 Opal RFX PIR's is constantly monitored. These signals are
directed to their respective volt free outputs and in addition there are
a further eight individual monitoring and information outputs.
RFX-3 RECEIVER (GJD017)
SUPPLY:
12 VDC @ 35mA nominal (9 to 20VDC maximum)
OUTPUTS (CCTV):
3 x independent channel outputs (24hr)
Selectable N/O (form A) or N/C (form B)
Individual timers 0.4 to 60 seconds after last
detection. Non volatile memory.
OUTPUTS (A):
3 x independent switching -ve outputs (24hr)
rated @ 250mA - 0.4 second on detection
RF loss of signal outputs:
3 x RF/signal -ve switching rated @ 250mA
Lux OUTPUT (S):
1 x photocell controlled -ve switching
Active 60 seconds after last detection
TAMPER:
Back & Front tamper volt free output (form B)
INDICATION WITH OUTPUTS:
Independent channel active & low battery
TEMPERATURE: -20º C +55º C
WEATHERPROOF ENCLOSURE:
IP65 high impact ABS
Weight - 340 grams
183 high x 123 wide x 60mm deep
-1-
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for GJD Opal RFX
Summary of Contents for GJD Opal RFX
- Page 1 The weatherproof receiver with front and rear tamper output can be positioned in line of sight up to 150m away. The active state of up to 3 Opal RFX PIR’s is constantly monitored. These signals are directed to their respective volt free outputs and in addition there are a further eight individual monitoring and information outputs.
- Page 2 FEATURES: The RFX - 3 Receiver monitors the active state of up to three Opal RFX passive infra red detectors. 1. Secure wire code transfer connector The RFX-3 Receiver can be mounted externally or internally. The transmission distance of 150m can be 2.
-
Page 3: Battery Installation
5. The ‘Channel” indicator blinks twice. The code for that detector is stored and registered to that channel. 6. Remove the link wire from the receiver and plug into 1. Remove the Opal RFX cover the aerial transmitter in the back of the detector (see fig 5). -
Page 4: Pulse Count
To enter the RF continuity test mode - press the (b) Wait until LED goes of (4 seconds) program button on the Opal RFX ‘Eight’ times. (c) Press three times for 20m One the eighth press - ‘hold’ the button down... -
Page 5: Testing The Outputs
‘1’ is automatically selected. The unit can the Opal RFX and the RFX-3 Receiver can be then be alighned. The red indicator will light easily established. - Page 6 Floodlights also emit haze ripple. When installing floodlights to provided movement activated lighting, position the floodlights at the side or above the detector. A minimum of 60cm (2 feet) is recommended, provided the detector is not in direct radiated hear from floodlight. Once alignment is completed, check that the vent hole to the front cover is positioned at the bottom.
- Page 7 MULTI BEAM LENS DATA The GJD multifunction lens fitted to the OPAL RFX detector produces 9 long range beams and 9 medium to short range curtain beams. Movement across the beams produces the best response and range, whilst movement towards the detector will be less responsive.
- Page 8 ENGINEER NOTES Technical: 01706 363990 Sales: 01706 363998 Fax: 01706 363991 Email: info@gjd.co.uk Unit 2, Birch Business Park, Whittle,Lane,Heywood,OL10 2SX...
Need help?
Do you have a question about the Opal RFX and is the answer not in the manual?
Questions and answers